i have issue like a beginer
How i want it:
SFP+ and ports 23, 24 are trunks uplinks with all vlans
ports 1-22 are access, vlan 6 and vlan 21
vlan 1 is for device managment, it works properly until I enable Vlan filtering on bridge interface:
After that i am disconected and cant access device anymore if i dont use safe mode ... which recover my wrong config.
I configured it following wiki: https://wiki.mikrotik.com/wiki/Manual:I ... s_Ports.29 What I am doing wrong? I am connectung to switch via trunk to vlan 1 mgmt ip.
It is good to use it this way, are there any limitation? Can i mix 100Mbit and 1000Mbit ports for users no any slowdown for them?
My configuration:
Code: Select all
# oct/03/2021 02:46:38 by RouterOS 6.48.4
# software id = 0QYR-DVY8
#
# model = CRS326-24G-2S+
# serial number = CDA80CA77283
/interface ethernet
set [ find default-name=ether23 ] comment=TRUNK to next switch
set [ find default-name=ether24 ] comment=TRUNK to next switch
set [ find default-name=sfp-sfpplus1 ] comment=TRUNK
set [ find default-name=sfp-sfpplus2 ] comment=TRUNK
/interface bridge
add name=bridge1 protocol-mode=none
/interface vlan
add interface=bridge1 name=vlan1 vlan-id=1
/interface bridge port
add bridge=bridge1 interface=sfp-sfpplus1
add bridge=bridge1 interface=sfp-sfpplus2
add bridge=bridge1 interface=ether24
add bridge=bridge1 interface=ether23
add bridge=bridge1 interface=ether1 pvid=6
add bridge=bridge1 interface=ether2 pvid=6
add bridge=bridge1 interface=ether3 pvid=6
add bridge=bridge1 interface=ether4 pvid=6
add bridge=bridge1 interface=ether5 pvid=6
add bridge=bridge1 interface=ether6 pvid=6
add bridge=bridge1 interface=ether7 pvid=6
add bridge=bridge1 interface=ether8 pvid=6
add bridge=bridge1 interface=ether9 pvid=6
add bridge=bridge1 interface=ether10 pvid=6
add bridge=bridge1 interface=ether11 pvid=6
add bridge=bridge1 interface=ether12 pvid=6
add bridge=bridge1 interface=ether13 pvid=6
add bridge=bridge1 interface=ether14 pvid=6
add bridge=bridge1 interface=ether15 pvid=6
add bridge=bridge1 interface=ether16 pvid=6
add bridge=bridge1 interface=ether17 pvid=6
add bridge=bridge1 interface=ether18 pvid=6
add bridge=bridge1 interface=ether19 pvid=6
add bridge=bridge1 interface=ether20 pvid=6
add bridge=bridge1 interface=ether21 pvid=21
add bridge=bridge1 interface=ether22 pvid=21
/interface bridge vlan
add bridge=bridge1 tagged=sfp-sfpplus1,sfp-sfpplus2 untagged="ether1,ether2,et\
her3,ether4,ether5,ether6,ether7,ether8,ether9,ether10,ether11,ether12,eth\
er13,ether14,ether15,ether16,ether17,ether18,ether19,ether20" vlan-ids=6
add bridge=bridge1 tagged=sfp-sfpplus1,sfp-sfpplus2,ether23,ether24 vlan-ids=\
7
add bridge=bridge1 tagged=sfp-sfpplus1,sfp-sfpplus2,ether23,ether24 untagged=\
ether21,ether22 vlan-ids=21
add bridge=bridge1 tagged=ether23,ether24,sfp-sfpplus1,sfp-sfpplus2 vlan-ids=\
1
/ip address
add address=10.10.126.246/28 interface=vlan1 network=10.154.126.240
/ip dns
set servers=10.10.115.1
/ip route
add distance=1 gateway=10.10.126.241
/system clock
set time-zone-name=Europe/Prague
/system identity
set name=mt-crs326-Home
/system routerboard settings
set boot-os=router-os