I found no matter LAN IP address I set in Quick Set, the result of DHCP network and gateway will always 0.0.0.0/24 and gateway always 0.0.0.0.
Is it normal when we're using "Quick Set" or anything do I need to do after Quick set?
Thank you.
DHCP Network always 0.0.0.0/24 by Quick Set
You do not have the required permissions to view the files attached to this post.
Re: DHCP Network always 0.0.0.0/24 by Quick Set
Strange question for a trainer ...
No, it's not normal.
What quickset were you using ?
Please post /export hide-sensitive file=whatever
No, it's not normal.
What quickset were you using ?
Please post /export hide-sensitive file=whatever
Re: DHCP Network always 0.0.0.0/24 by Quick Set
I'm use "Quick Set" on cleaned configuration after reset without default configuration.
Following is what I set on Quick set
The result almost everything look like OK
IP pool is OK
Bridge Interface and IP Address of router itself is ok but only Network in DHCP show 0.0.0.0/24
Following is what I set on Quick set
The result almost everything look like OK
IP pool is OK
Bridge Interface and IP Address of router itself is ok but only Network in DHCP show 0.0.0.0/24
You do not have the required permissions to view the files attached to this post.
Re: DHCP Network always 0.0.0.0/24 by Quick Set
What device are you using ?
And why don't you apply firewall on your router ?
Export of config is easier then those screenshots. Not everything is shown.
Anyhow, it's something which can easily be set manually.
Network: 192.168.224.0/24
Gateway: whatever you need (but I think it should be 172.16.1.2 in your case)
DNS: whatever you need
And why don't you apply firewall on your router ?
Export of config is easier then those screenshots. Not everything is shown.
Anyhow, it's something which can easily be set manually.
Network: 192.168.224.0/24
Gateway: whatever you need (but I think it should be 172.16.1.2 in your case)
DNS: whatever you need
Re: DHCP Network always 0.0.0.0/24 by Quick Set
Quickset should only be used with a device in it's original state or to make additional changes as long as only Quickset was used.
It relies on a simple set of scripts to make changes to the original configuration and adding any settings outside of Quickset will have unexpected results. This would include a device in a no-default state.
It relies on a simple set of scripts to make changes to the original configuration and adding any settings outside of Quickset will have unexpected results. This would include a device in a no-default state.
Re: DHCP Network always 0.0.0.0/24 by Quick Set
try Quick set with default config doesn't make any different. still got 0.0.0.0/24 for DHCP NetworkQuickset should only be used with a device in it's original state or to make additional changes as long as only Quickset was used.
It relies on a simple set of scripts to make changes to the original configuration and adding any settings outside of Quickset will have unexpected results. This would include a device in a no-default state.
Re: DHCP Network always 0.0.0.0/24 by Quick Set
I'm try it on RB4011 / hEX got same result from both models.What device are you using ?
And why don't you apply firewall on your router ?
Export of config is easier then those screenshots. Not everything is shown.
Anyhow, it's something which can easily be set manually.
Network: 192.168.224.0/24
Gateway: whatever you need (but I think it should be 172.16.1.2 in your case)
DNS: whatever you need
This is not a production and I skipped firewall checkbox just because want to try at minimum setting to make RouterOS work. / It's just a lab to try the way to tell people how to make RouterOS run by use only single page with minimum setting
This is the exported of configuration
Code: Select all
# jan/02/1970 00:04:43 by RouterOS 6.49
# software id = KTAP-SQC0
#
# model = RB4011iGS+5HacQ2HnD
# serial number = A283092B80F1
/interface bridge
add name=bridge1
/interface wireless
set [ find default-name=wlan1 ] ssid=MikroTik
set [ find default-name=wlan2 ] ssid=MikroTik
/interface pppoe-client
add add-default-route=yes disabled=no interface=ether1 name=pppoe-out1 \
password=u1 use-peer-dns=yes user=u1
/interface ethernet switch port
set 0 default-vlan-id=0
set 1 default-vlan-id=0
set 2 default-vlan-id=0
set 3 default-vlan-id=0
set 4 default-vlan-id=0
set 5 default-vlan-id=0
set 6 default-vlan-id=0
set 7 default-vlan-id=0
set 8 default-vlan-id=0
set 9 default-vlan-id=0
set 10 default-vlan-id=0
set 11 default-vlan-id=0
/interface list
add name=WAN
add name=LAN
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
/ip pool
add name=dhcp ranges=192.168.224.100-192.168.224.199
/ip dhcp-server
add address-pool=dhcp disabled=no interface=bridge1 name=dhcp1
/interface bridge port
add bridge=bridge1 interface=ether2
add bridge=bridge1 interface=ether3
add bridge=bridge1 interface=ether4
add bridge=bridge1 interface=ether5
add bridge=bridge1 interface=ether6
add bridge=bridge1 interface=ether7
add bridge=bridge1 interface=ether8
add bridge=bridge1 interface=ether9
add bridge=bridge1 interface=ether10
add bridge=bridge1 interface=sfp-sfpplus1
add bridge=bridge1 interface=wlan1
add bridge=bridge1 interface=wlan2
/interface list member
add interface=pppoe-out1 list=WAN
add interface=bridge1 list=LAN
/ip address
add address=192.168.224.1/24 interface=bridge1 network=192.168.224.0
/ip dhcp-client
add interface=ether1
/ip dhcp-server network
add address=0.0.0.0/24 gateway=0.0.0.0 netmask=24
/ip firewall nat
add action=masquerade chain=srcnat out-interface-list=WAN
/system leds
add interface=wlan2 leds="wlan2_signal1-led,wlan2_signal2-led,wlan2_signal3-led,\
wlan2_signal4-led,wlan2_signal5-led" type=wireless-signal-strength
add interface=wlan2 leds=wlan2_tx-led type=interface-transmit
add interface=wlan2 leds=wlan2_rx-led type=interface-receive
Re: DHCP Network always 0.0.0.0/24 by Quick Set
I am not sure about that statement.
If I use a default Quickset on my Hex, it simply works.
I'll have a look later.
If I use a default Quickset on my Hex, it simply works.
I'll have a look later.
Re: DHCP Network always 0.0.0.0/24 by Quick Set
NetInstall 6.49 with "Apply default config" checked. For some time now, the default bridge name has been name=bridge and yours is name=bridge1. I believe the default config has been altered and is causing the Quickset scripts to error and stop.
Re: DHCP Network always 0.0.0.0/24 by Quick Set
Wow.. got it. Thank you. ^_^NetInstall 6.49 with "Apply default config" checked. For some time now, the default bridge name has been name=bridge and yours is name=bridge1. I believe the default config has been altered and is causing the Quickset scripts to error and stop.