try to usb 3.0 pins isolated (PINS:23,25,27,31,33)Hello, I am testing a telit lm960 card with a LHG-LTE-KIT-US but mikrotik does not recognize the lm960, someone knows if it is compatible
I know about 2 things to check:Hello, I am testing a telit lm960 card with a LHG-LTE-KIT-US but mikrotik does not recognize the lm960, someone knows if it is compatible
LM960 works In 6.46. At least it's detected. In RB912.Note the update 6.45.7, it disables support for this card, but Mikrotik promised to improve it in the next version.
How did you go? Mikrotik did some work getting an LE910C1 working for me in ECM mode (pid 0x1206) It does come up with the LTE interface and a local IP address is obtained from the DHCP server on the module and playing with the serial commands I see the carrier appears to have allocated their own CGNAT IP address to the card and so on BUT it still didn't talk to the internet.LM960 works In 6.46. At least it's detected. In RB912.Note the update 6.45.7, it disables support for this card, but Mikrotik promised to improve it in the next version.
- again in serial-terminal AT#USBCFG=3 to " expose CDC-ECM network interface" <- thx to MT support
interface lte at-chat LTE1 input="AT#cainfo\?"Ko, how did you get the AT#CAINFO? command to run in routeros? The question mark being a special character doesn't play nice with the os.
Band locking is similar.Would just like to know about that AT#CAINFO? command, also the band lock commands.
interface lte at-chat LTE1 input="AT#cainfo\?" shows parameters (signal strange, band, channel width etc). Can you post here result?Hello I'm totaly newbe in sending any AT comands. I have RMB33 & TELIT LM940. The problem is that every 24-48 h LTE stops. My max download is about 15. I want to check if my cart works in CA . If anyone can help me step by step what to do?
Its connected onThat's what I have
output: #CAINFO: 126,3025,4,471,-76,-40,-18,81,e2ae,0,2,1,120,54,3,450,-76,
-33,-20,74,2,0,1,0,0,0,0,0,0,0,0,0,0,0 OK
Thanks!> interface lte info lte1
pin-status: ok
registration-status: not searching
functionality: full
manufacturer: Telit
model: LM960A18
revision: 32.00.144
imei: 356299100024122
imsi: 234304183162269
subscriber-number: "Own Number","***********",129
Did you set generic firmware?Hi All
Can someone help?
Thought I'd done all the right steps, the LM960 shows up as an LTE interface (lte1). However it is "not searching".
How do I resolved this?Thanks!> interface lte info lte1
pin-status: ok
registration-status: not searching
functionality: full
manufacturer: Telit
model: LM960A18
revision: 32.00.144
imei: 356299100024122
imsi: 234304183162269
subscriber-number: "Own Number","***********",129
[admin@MikroTik] > system resource usb print
# DEVICE VENDOR NAME
0 1-0 Linux 3.3.5 ehci_hcd RB400 EHCI
1 1-1 Telit Wireless Solutions LM960A18
[admin@MikroTik] > interface print
Flags: D - dynamic, X - disabled, R - running, S - slave
# NAME TYPE ACTUAL-MTU L2MTU MAX-L2MTU MAC-ADDRESS
0 R ether1 ether 1500 1598 2028 C4:AD:34:71:2D:F7
[admin@MikroTik] > /system serial-terminal usb1 channel=6
input does not match any value of port
[admin@MikroTik] >
PIN isolation is only to force it to USB 2.0 (if LM960 is set to use USB 3.0). SInce you see it under USB device, that's not needed.
system serial-terminal usb1 channel=6 no longer works and let interface doesn't show.
Yes. You will have problem. First of all NEVER run any radio module without antenna attached. It's way to burn it.Thanks!
I have ordered a USB to miniPCIe adapter.
Perhaps you can confirm if I will have issues not having 4x4 MIMO antenna connected as I'm trying to use this in an LHG-LTE? I need to be able to get CA on bands 1,3,7,20 (4CA). MHF4 to u.FL pigtails on their way...
I can not add a DHCP client to the lte1 interface?[admin@MikroTik] > interface lte info lte1
pin-status: ok
registration-status: registered
functionality: full
manufacturer: Telit
model: LM960A18
revision: 32.00.114
current-operator: vodafone UK
lac: 8279
current-cellid: 133750804
enb-id: 522464
sector-id: 20
access-technology: Evolved 3G (LTE)
imei: 356299100024122
imsi: 234159521654983
earfcn: 6300 (band 20)
rssi: -61dBm
rsrp: -88dBm
rsrq: -10dB
[admin@MikroTik] > ip address print
Flags: X - disabled, I - invalid, D - dynamic
# ADDRESS NETWORK INTERFACE
0 ;;; defconf
192.168.88.1/24 192.168.88.0 ether1
No need to set DHCP it should wok without it, regardless how strange it is.Ah that's a pain. So I might not be able to use this in the LHG...
Perhaps I can use in a wAP LTE and get MHF4 to SMA pigtails for an external 4x4 MIMO antenna.
Anyway I now have the modem showing up in the Mikrotik (after using a USB mini-PCIe adapter) and PuTTY to issue AT command to get back to the right mode.
Next problem is that although it shows registered it is not getting an IP address and therefore no internet connectivity.
I can not add a DHCP client to the lte1 interface?[admin@MikroTik] > interface lte info lte1
pin-status: ok
registration-status: registered
functionality: full
manufacturer: Telit
model: LM960A18
revision: 32.00.114
current-operator: vodafone UK
lac: 8279
current-cellid: 133750804
enb-id: 522464
sector-id: 20
access-technology: Evolved 3G (LTE)
imei: 356299100024122
imsi: 234159521654983
earfcn: 6300 (band 20)
rssi: -61dBm
rsrp: -88dBm
rsrq: -10dB
[admin@MikroTik] > ip address print
Flags: X - disabled, I - invalid, D - dynamic
# ADDRESS NETWORK INTERFACE
0 ;;; defconf
192.168.88.1/24 192.168.88.0 ether1
How do I resolve this issue?
[admin@MikroTik] > interface lte at-chat lte1 input="AT#ACTIVEFW=1,1"
output: OK
[admin@MikroTik] > interface lte at-chat lte1 input="AT#GETFW"
output: HOST FIRMWARE : 32.00.005_1 SLOT STATUS CARRIER VERSION TMCFG CNV 1 Activated Generic 32.00.114 1023 e
Verizon 32.00.124 2020 empty 3 ATT 32.00.144 4021 empty 4 TMUS 32.00.153 5004 empty OK
I know. I spent a month learning, searching, testing. And gave up finally. Will run it on linux. Installing up ubuntu, and connecting that modem took me 15min. Including external public IP, which turned out is not possible on mikrotik with LM960. I'm not linux guru at all!Hmm so frustrating, it has signal, it's registered but just not connecting.
Was it straight forward after you updated the firmware or you had to do something? I want to buy the Telit LM960 and I have a mikrotik routherboard RBM11G https://mikrotik.com/product/m11g, not sure if it will work out of the box, does anybody know?YAY it is working after updating the firmware on the LM960.
Upgraded from 32.00.114 to 32.00.115
This is few other thread's at this topic.I am looking for a solution to use in the USA.. im a tad frustrated with LTE modems right npw... I have a desk drawer full of them..
...
id really like to get CA operational ..
This is cat.4, one band and dependence of SINR & CQI...ive got an EC25-AF that works in MBIM mode with ROS7. but it is slow..
It cannot, it's cat.4 means no CA. From Cat.6 you have do a CA, the SISO or MIMO antennas is differ topic then CA.I didnt think the EC25-AF can do CA since it only takes 2x2 antenna? mayube I just need better antenna for my EC25..
support@quctel.com ? They answer good for me but better is account at https://e-service.quectel.com/en/support/login then forum who answer you to write to e-mail.
Internal of SXTR or LHGR or LDFR.which antenna do you like best for your EC25-AF?
Hi, I am very interested in guide. Recent I bought RBM33G and I am deciding to buy lm960a18. I already have antenna QuPanel LTE HP MIMO 4x4.Hi everyone, we are a group of Italian guys who are trying to make an lm960a18 work on rbm33g and we actually succeeded, with two lpda's inside the B3 house (-85 / -90db) vodafone italia, we reached almost 170dl 70ul. Slowly let's see if we can make a guide, even video of the whole. We have also created a telegram channel and a discord channel and by staying hours and hours on anydesk we have achieved various objectives.
Check TELIT LM940 HowToHi, I am very interested in guide. Recent I bought RBM33G and I am deciding to buy lm960a18.