Hi All,
I'm having a strange SFP port issue with my CCR-1036-12G-4S router.
As soon as I reboot the router, the SFP port goes down. I manually have to disable and enable the SFP port to work again. The Auto-negotiation is disabled and the speed is set to 1G.
My SFP module details are below:
Vendor: UBNT
Model: UF-RJ45-1G
Vendor Serial: X20062802607
The same SFP module works flawlessly with my RB3011 and RB4011 routers. Is there any workaround for this? Please help.
-
-
mahfuzazam
newbie
- Posts: 37
- Joined:
- Location: Usa
- Contact:
Re: MikroTik CCR SFP Port Issue
What RouterOS version and firmware are you using?
Re: MikroTik CCR SFP Port Issue
Have you asked for support on the Ubiquiti Forum or Ubiquiti Support?
-
-
mahfuzazam
newbie
- Posts: 37
- Joined:
- Location: Usa
- Contact:
Re: MikroTik CCR SFP Port Issue
I'm using the latest stable v6.49.6 version.What RouterOS version and firmware are you using?
-
-
mahfuzazam
newbie
- Posts: 37
- Joined:
- Location: Usa
- Contact:
Re: MikroTik CCR SFP Port Issue
This is happening with all SFP modules. Recently tried with ATOP modules as well, but had same result.Have you asked for support on the Ubiquiti Forum or Ubiquiti Support?
-
-
mahfuzazam
newbie
- Posts: 37
- Joined:
- Location: Usa
- Contact:
Re: MikroTik CCR SFP Port Issue
I got it working with a simple startup script, which disables and then enables the SFP interface.
But wanted to know if this can be fixed without any scheduler. Thanks for helping
But wanted to know if this can be fixed without any scheduler. Thanks for helping
Re: MikroTik CCR SFP Port Issue
other end of that link is configured manually at 1g ?
-
-
mahfuzazam
newbie
- Posts: 37
- Joined:
- Location: Usa
- Contact:
Re: MikroTik CCR SFP Port Issue
The line came from a media converter which auto negotiates to 1G when connected to switch via ethernet cable.other end of that link is configured manually at 1g ?
Also, the same link works perfectly with SFP module, when connected to RB3011, 4011.
This is why I'm confused. Is there any settings to be done from the CCR end to have it running without scripts??
-
-
StubArea51
Trainer
- Posts: 1739
- Joined:
- Location: stubarea51.net
- Contact:
Re: MikroTik CCR SFP Port Issue
This isn't normal behavior for a CCR1036, what version of RouterOS are you running and how old is the CCR?
-
-
mahfuzazam
newbie
- Posts: 37
- Joined:
- Location: Usa
- Contact:
Re: MikroTik CCR SFP Port Issue
I'm running latest stable version 6.49.6 and the router model is CCR 1036-12G-4S. The router was purchased 7-8 years ago.This isn't normal behavior for a CCR1036, what version of RouterOS are you running and how old is the CCR?
-
-
StubArea51
Trainer
- Posts: 1739
- Joined:
- Location: stubarea51.net
- Contact:
Re: MikroTik CCR SFP Port Issue
the router model is CCR 1036-12G-4S. The router was purchased 7-8 years ago.
What is the output of
Code: Select all
system health print-
-
mahfuzazam
newbie
- Posts: 37
- Joined:
- Location: Usa
- Contact:
Re: MikroTik CCR SFP Port Issue
[M@MikroTik] > system health printthe router model is CCR 1036-12G-4S. The router was purchased 7-8 years ago.
What is the output of
Code: Select allsystem health print
fan-mode: auto
use-fan: main
active-fan: main
cpu-overtemp-check: yes
cpu-overtemp-threshold: 100C
cpu-overtemp-startup-delay: 1m
voltage: 24V
current: 1547mA
temperature: 30C
cpu-temperature: 56C
power-consumption: 37.1W
fan1-speed: 2704RPM
fan2-speed: 2704RPM