Community discussions

MikroTik App
 
RyperX
Frequent Visitor
Frequent Visitor
Topic Author
Posts: 72
Joined: Thu May 21, 2015 11:14 am

Problem upgrading rb2011 from 7.1beta6 to v7.1(.1)

Fri Jan 07, 2022 11:06 am

Hey guys,
i have a problem with upgrading my rb2011 to the latest version.
At the moment is 7.1beta6 installed and when i try to install to 7.1 or 7.1.1 the router reboots and at the next boot it is still on the beta6

I only see in the log files a kernel failure:
kernel failure in previous boot

At the moment i only tried it through the Package Upgrade Option in Winbox
Config was freshly created on the 7.1beta6 firmware
 
hecatae
Member Candidate
Member Candidate
Posts: 244
Joined: Thu May 21, 2020 2:34 pm

Re: Problem upgrading rb2011 from 7.1beta6 to v7.1(.1)

Fri Jan 07, 2022 9:36 pm

On my rb2011uias I had to copy the update to the Files storage location and then reboot.

Otherwise I had the same issue you mention.
 
RyperX
Frequent Visitor
Frequent Visitor
Topic Author
Posts: 72
Joined: Thu May 21, 2015 11:14 am

Re: Problem upgrading rb2011 from 7.1beta6 to v7.1(.1)

Sat Jan 08, 2022 12:02 am

Thanks, will try this out the next days.
I only need to download the update file from the homepage, but it into "files" root folder and reboot the router, as i am remember correctly
 
mducharme
Trainer
Trainer
Posts: 1777
Joined: Tue Jul 19, 2016 6:45 pm
Location: Vancouver, BC, Canada

Re: Problem upgrading rb2011 from 7.1beta6 to v7.1(.1)

Sun Jan 09, 2022 5:20 am

7.1beta6 had serious issues that often prevented upgrading from 7.1beta6 to anything later. You should reset your router to no-default-configuration so it is completely blank and then upgrade.

In my experience the problem is normally caused if the router has any bridges whatsoever. It will crash every reboot causing any upgrade attempt to fail. Resetting configuration to regular factory defaults therefore doesn't allow the upgrade to work because it creates a bridge.
 
RyperX
Frequent Visitor
Frequent Visitor
Topic Author
Posts: 72
Joined: Thu May 21, 2015 11:14 am

Re: Problem upgrading rb2011 from 7.1beta6 to v7.1(.1)

Thu Jan 13, 2022 3:36 pm

Sadly i still had the problem with completly default config.
Should i reset and restore no config and try it that way?

The funny thing at the moment i am on beta6 and i upgraded it already to a newer version on another partition, because a crash i needed to go back to beta6.
Is it possible to get an older version to download to test it? For example beta7?

Config for the moment is nealy default (setup after i tried with default config)
Only mayor change to stock is i have an pppoe and wireguard interface
 
fragtion
Member Candidate
Member Candidate
Posts: 257
Joined: Fri Nov 13, 2009 10:08 pm
Location: Johannesburg, South Africa

Re: Problem upgrading rb2011 from 7.1beta6 to v7.1(.1)

Thu Jan 13, 2022 3:40 pm

"Default configuration" includes a bridge with ethernet devices so resetting to blank config will help with that
 
mducharme
Trainer
Trainer
Posts: 1777
Joined: Tue Jul 19, 2016 6:45 pm
Location: Vancouver, BC, Canada

Re: Problem upgrading rb2011 from 7.1beta6 to v7.1(.1)

Thu Jan 13, 2022 5:11 pm

Yes, as I clearly stated, you have to reset to no-default-config, so that the device config is completely empty, without even an IP address. Resetting to default config will NOT help at all as the bridge will still exist.

You will need to use MAC winbox to upload the npk file to a device that doesn't have any configuration whatsoever as it won't have an IP for you to connect to.
Last edited by mducharme on Fri Jan 14, 2022 1:28 am, edited 1 time in total.
 
sirmax
just joined
Posts: 13
Joined: Wed Mar 13, 2013 12:39 pm

Re: Problem upgrading rb2011 from 7.1beta6 to v7.1(.1)

Fri Jan 14, 2022 12:18 am

Had the same issue but my topic was removed for some reason.

Try to remove bridges before upgrading pls.
 
RyperX
Frequent Visitor
Frequent Visitor
Topic Author
Posts: 72
Joined: Thu May 21, 2015 11:14 am

Re: Problem upgrading rb2011 from 7.1beta6 to v7.1(.1)

Fri Jan 14, 2022 9:28 am

Thanks!
Will test this next week when i am next to the router again
 
RyperX
Frequent Visitor
Frequent Visitor
Topic Author
Posts: 72
Joined: Thu May 21, 2015 11:14 am

Re: Problem upgrading rb2011 from 7.1beta6 to v7.1(.1)

Sat Jan 22, 2022 7:32 pm

For information, it was enough to disable the bridge and all other Interfaces.
The Update ran fine and after that i enabled everything again.
 
sirmax
just joined
Posts: 13
Joined: Wed Mar 13, 2013 12:39 pm

Re: Problem upgrading rb2011 from 7.1beta6 to v7.1(.1)

Mon Jun 27, 2022 4:01 pm

Tested today

Removed all bridges and update works as expected
 /routing/bgp/connection> /system/routerboard/print
       routerboard: yes
             model: 2011UAS-2HnD
     serial-number: 40260270651E
     firmware-type: ar9344
  factory-firmware: 3.0
  current-firmware: 3.33
  upgrade-firmware: 7.4beta4
 
kiano
just joined
Posts: 6
Joined: Sun Mar 11, 2018 9:08 pm

Re: Problem upgrading rb2011 from 7.1beta6 to v7.1(.1)

Mon Jan 09, 2023 3:16 am

7.1beta6 had serious issues that often prevented upgrading from 7.1beta6 to anything later. You should reset your router to no-default-configuration so it is completely blank and then upgrade.

In my experience the problem is normally caused if the router has any bridges whatsoever. It will crash every reboot causing any upgrade attempt to fail. Resetting configuration to regular factory defaults therefore doesn't allow the upgrade to work because it creates a bridge.
thank you so much! disabling bridge helped me ))

Who is online

Users browsing this forum: No registered users and 22 guests