Sorry for the delay but I had to check some configuration options.
I was testing a couple of configuration scenarios in 3rd location, using HEX760 and Cap XL ac.
There should be 600/30 Mb/s of speed. When I'm using wired connection the speed is about 570-590 / 27-30.
After a lot of changes I finally get 400-420 / 25-30 by wireless connection.
Of course this is better than 50% I got before (280-300) but still it is not acceptable for me.
Especially, when I replaced Cap XL with Ubiquiti UAP AC LITE (the old version, not the new one) with almost default configuration I got 500-520.
After few fixes there was 550-570 and this is what I am expect from MT.
There are the best configs I am able to do:
1) hex760iGS as an edge-router and capsman at the same time. there is default config with my changes:
/caps-man channel
add band=5ghz-onlyac control-channel-width=20mhz extension-channel=Ceee \
frequency=5180 name=ch-5
/caps-man datapath
add local-forwarding=yes name=datapath1
/interface bridge
add name=bridge
/caps-man rates
add basic=12Mbps,24Mbps,36Mbps,48Mbps,54Mbps name=rate-5g supported=\
24Mbps,36Mbps,48Mbps,54Mbps
/caps-man security
add authentication-types=wpa2-psk encryption=aes-ccm group-encryption=aes-ccm \
name=xl123
/caps-man configuration
add channel=ch-5 country=poland datapath=datapath1 distance=indoors \
hw-protection-mode=rts-cts hw-retries=5 installation=indoor mode=ap \
multicast-helper=full name=cfg-5 rates=rate-5g security=xl123 ssid=xl123
/interface list
add comment=defconf name=WAN
add comment=defconf name=LAN
add include=WAN name=MGMT
/interface lte apn
set [ find default=yes ] ip-type=ipv4 use-network-apn=no
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
/ip pool
add name=dhcp_pool0 ranges=172.31.4.2-172.31.4.254
/ip dhcp-server
add address-pool=dhcp_pool0 interface=bridge name=dhcp1
/port
set 0 name=serial0
/caps-man manager
set enabled=yes
/caps-man provisioning
add action=create-dynamic-enabled hw-supported-modes=ac master-configuration=\
cfg-5 name-format=identity name-prefix=5G
/interface bridge port
add bridge=bridge ingress-filtering=no interface=ether3
add bridge=bridge ingress-filtering=no interface=ether4
add bridge=bridge ingress-filtering=no interface=ether1
/ip neighbor discovery-settings
set discover-interface-list=MGMT
/ipv6 settings
set disable-ipv6=yes max-neighbor-entries=8192
/interface list member
add interface=ether2 list=WAN
add interface=bridge list=LAN
add interface=ether5 list=MGMT
/interface ovpn-server server
set auth=sha1,md5
/ip address
add address=172.31.4.1/24 interface=bridge network=172.31.4.0
/ip dhcp-client
add interface=ether2
/ip dhcp-server network
add address=172.31.4.0/24 gateway=172.31.4.1
/ip firewall filter
add action=accept chain=input comment=\
"defconf: accept established,related,untracked" connection-state=\
established,related,untracked
add action=drop chain=input comment="defconf: drop invalid" connection-state=\
invalid
add action=accept chain=input comment="defconf: accept ICMP" protocol=icmp
add action=accept chain=input comment=\
"defconf: accept to local loopback (for CAPsMAN)" dst-address=127.0.0.1
add action=drop chain=input comment="defconf: drop all not coming from LAN" \
in-interface-list=!LAN
add action=accept chain=forward comment="defconf: accept in ipsec policy" \
ipsec-policy=in,ipsec
add action=accept chain=forward comment="defconf: accept out ipsec policy" \
ipsec-policy=out,ipsec
add action=fasttrack-connection chain=forward comment="defconf: fasttrack" \
connection-state=established,related hw-offload=yes
add action=accept chain=forward comment=\
"defconf: accept established,related, untracked" connection-state=\
established,related,untracked
add action=drop chain=forward comment="defconf: drop invalid" \
connection-state=invalid
add action=drop chain=forward comment=\
"defconf: drop all from WAN not DSTNATed" connection-nat-state=!dstnat \
connection-state=new in-interface-list=WAN
/ip firewall nat
add action=masquerade chain=srcnat comment="defconf: masquerade" \
ipsec-policy=out,none out-interface-list=WAN
/system clock
set time-zone-name=Europe/Warsaw
/system identity
set name=test-main
/system routerboard settings
set silent-boot=yes
/tool romon
set enabled=yes
2) Cap xl ac as the Cap itself
there is default caps mode configuration with my changes:
/interface bridge
add admin-mac=[here was the mac address] auto-mac=no comment=defconf name=bridgeLocal
/interface wireless
set [ find default-name=wlan1 ] ssid=MikroTik
set [ find default-name=wlan2 ] adaptive-noise-immunity=ap-and-client-mode \
band=5ghz-onlyac disabled=no mode=ap-bridge ssid=MikroTik wmm-support=\
enabled
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
/ip hotspot profile
set [ find default=yes ] html-directory=hotspot
/interface bridge port
add bridge=bridgeLocal comment=defconf interface=ether1
add bridge=bridgeLocal comment=defconf interface=ether2
/interface wireless cap
set bridge=bridgeLocal discovery-interfaces=bridgeLocal enabled=yes \
interfaces=wlan2
/ip dhcp-client
add comment=defconf interface=bridgeLocal
/system clock
set time-zone-name=Europe/Warsaw
/system identity
set name=test-xl123
/tool romon
set enabled=yes
Config was exported by:
Both devices were upgraded to 7.8 version of RouterOS and RouterBoard firmware.
Any suggestions?