Community discussions

MikroTik App
 
geosoft1
just joined
Topic Author
Posts: 16
Joined: Tue Aug 04, 2015 1:49 pm

RB951G-2HnD reset issue

Sun Oct 18, 2020 4:27 pm

Hi,
Recently I bought a RB951G-2HnD unit having the following relevant characteristics:
Architecture Name		mipsbe
Board Name		        RB951G-2HnD
Version		                6.44.5 (long-term)
Build Time		        Jul/04/2019 10:32:21
Factory Software		6.44
Model		                RB951G-2HnD
Serial Number		        96500BF5BD1E
Firmware Type                ar9344
Factory Firmware		6.44
Current Firmware		6.44.5
Upgrade Firmware		6.44.5
The router works fine but today I found out that I'm not able to reset at factory defaults from the hardware button. Trying the reset by holding reset button during the power up I observed that ACT led do not start blinking anymore (as ussual) and the router boot normaly (I'm familiar with Mikrotik routers and I tried this several times). On the other hand the router can be reset from System->Reset configuration. Also the Protected Routerboot parameter is not setted.

Any advice around this issue? Could be a software issue or a hardware one? (I mention that the router is new).

Thank you,
George
Last edited by geosoft1 on Sun Oct 18, 2020 7:43 pm, edited 1 time in total.
 
sindy
Forum Guru
Forum Guru
Posts: 10205
Joined: Mon Dec 04, 2017 9:19 pm

Re: RB951G-2HnD reset issue

Sun Oct 18, 2020 4:34 pm

What happens if you press the reset button while the router is running? Does it cause a restart?
 
geosoft1
just joined
Topic Author
Posts: 16
Joined: Tue Aug 04, 2015 1:49 pm

Re: RB951G-2HnD reset issue

Sun Oct 18, 2020 7:41 pm

Nothing happens even if I press it short or long (eg. over 10 sec). The router continues to run normally.
 
sindy
Forum Guru
Forum Guru
Posts: 10205
Joined: Mon Dec 04, 2017 9:19 pm

Re: RB951G-2HnD reset issue

Sun Oct 18, 2020 9:07 pm

Sorry, this was a useless question. The button may be broken, but it cannot be tested during runtime.
What does system routerboard settings print show?
 
geosoft1
just joined
Topic Author
Posts: 16
Joined: Tue Aug 04, 2015 1:49 pm

Re: RB951G-2HnD reset issue

Mon Oct 19, 2020 5:12 pm

             auto-upgrade: no
                init-delay: 0s
               boot-device: nand-if-fail-then-ethernet
             cpu-frequency: 600MHz
             boot-protocol: bootp
       force-backup-booter: no
               silent-boot: no
      protected-routerboot: disabled
      reformat-hold-button: 20s
  reformat-hold-button-max: 10m
 
erlinden
Forum Guru
Forum Guru
Posts: 1920
Joined: Wed Jun 12, 2013 1:59 pm
Location: Netherlands

Re: RB951G-2HnD reset issue

Mon Oct 19, 2020 5:16 pm

What about resetting it using the command /system reset-configuration?
And while you are at it...you might want to upgrade the RouterOS and firmware.
 
geosoft1
just joined
Topic Author
Posts: 16
Joined: Tue Aug 04, 2015 1:49 pm

Re: RB951G-2HnD reset issue

Mon Oct 19, 2020 6:18 pm

Well, the command /system reset-configuration still works. In fact the router didn't seems to have other issues. The strange thing is that ACT led didn't start blinking when I held the button and I can't figured out if this is a software issue or hardware problem and I should returned it back to the warranty.
 
pe1chl
Forum Guru
Forum Guru
Posts: 10195
Joined: Mon Jun 08, 2015 12:09 pm

Re: RB951G-2HnD reset issue

Mon Oct 19, 2020 7:43 pm

The button may be broken. This sometimes happens because there is so little feedback whether you have pressed it correctly, and sometimes people react by pressing it ever firmer...
However, many models also have a hole in the circuit board where you can reset the router using anything that bridges the PCB track segments along the hole.
(e.g. a phillips screwdriver of the appropriate size)
 
geosoft1
just joined
Topic Author
Posts: 16
Joined: Tue Aug 04, 2015 1:49 pm

Re: RB951G-2HnD reset issue

Mon Oct 19, 2020 8:22 pm

So, I understand that no software reasons could lead at this behavior an the most probably the button is broken. I will try with the reset hole and if it fails perhaps I will send back to warranty.
Thank you guys for your answers and support.
 
erlinden
Forum Guru
Forum Guru
Posts: 1920
Joined: Wed Jun 12, 2013 1:59 pm
Location: Netherlands

Re: RB951G-2HnD reset issue

Tue Oct 20, 2020 10:04 am

I found this topic, might explain the behavior:
viewtopic.php?t=114200

Does the reset button work again?
 
pe1chl
Forum Guru
Forum Guru
Posts: 10195
Joined: Mon Jun 08, 2015 12:09 pm

Re: RB951G-2HnD reset issue

Tue Oct 20, 2020 11:22 am

I found this topic, might explain the behavior:
viewtopic.php?t=114200
He already covered that.
 
Beltus1
just joined
Posts: 3
Joined: Mon May 15, 2023 4:39 pm

Re: RB951G-2HnD reset issue

Mon May 15, 2023 4:53 pm

I am having same issue, when i hold reset button led light pause n later start blinking then i release reset button yet nothing

Who is online

Users browsing this forum: Amazon [Bot], Bolendox, eworm, fibracapi, Majestic-12 [Bot], Semrush [Bot] and 79 guests