I have problem with winbox access and web interface while bonding is activated on both ends.
I have the following scenario shown on the picture, my network is OSPF routed and I have bonding on both ends .
When I disable bonding I get access on 10.6.1.2 and 10.22.1.2 also on 10.6.3 and 10.22.13 devices . Winbox and Web interface are ok without bonding.
I read the documents and notice somewhere that VLAN tagging needs to be added on bonding interfaces , separate VLAN for management. If someone has experience in this sphere please help
I am sorry for large pictures
Network topology AirFiber 5XHD info 10.22.1.2 AirFiber 5XHD info 10.22.1.3 R1 config
Code: Select all
# nov/26/2021 11:58:33 by RouterOS 6.48.2
/interface bridge
add name=bridge1
add name=loopback
/interface ethernet
set [ find default-name=ether1 ] comment=
set [ find default-name=ether2 ] comment=
set [ find default-name=ether3 ] comment="NetMetal"
set [ find default-name=ether4 ] comment=
set [ find default-name=ether5 ] comment=
set [ find default-name=ether6 ] comment=
set [ find default-name=ether7 ] comment=
set [ find default-name=ether8 ] comment=
set [ find default-name=ether9 ] comment=
set [ find default-name=ether10 ] comment="AirFiber"
/interface bonding
add arp-ip-targets=10.1.255.59 comment=Airfiber_Netmetal link-monitoring=arp name=\
bonding2 slaves=ether3,ether10 transmit-hash-policy=layer-2-and-3
/interface ethernet switch port
set 0 default-vlan-id=0
set 1 default-vlan-id=0
set 2 default-vlan-id=0
set 3 default-vlan-id=0
set 4 default-vlan-id=0
set 5 default-vlan-id=0
set 6 default-vlan-id=0
set 7 default-vlan-id=0
set 8 default-vlan-id=0
set 9 default-vlan-id=0
set 10 default-vlan-id=0
set 11 default-vlan-id=0
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
/routing ospf area
set [ find default=yes ] disabled=yes
add area-id=2.2.2.2 default-cost=1 inject-summary-lsas=no name=area2 type=\
stub
/routing ospf instance
set [ find default=yes ] router-id=10.1.255.51
/interface bridge port
add bridge=bridge1 interface=ether4
add bridge=bridge1 interface=ether5
add bridge=bridge1 interface=ether7
add bridge=bridge1 interface=ether8
add bridge=bridge1 interface=ether9
/ip address
add address=10.2.1.4/24 interface=bridge1 network=10.2.1.0
add address=10.1.255.51 interface=loopback network=10.1.255.51
add address=10.22.1.1/24 interface=bonding2 network=10.22.1.0
add address=10.6.1.1/24 interface=bonding2 network=10.6.1.0
/ip cloud
set update-time=no
/ip firewall mangle
add action=change-dscp chain=prerouting new-dscp=7 passthrough=no protocol=\
ospf
add action=set-priority chain=output new-priority=7 passthrough=yes protocol=\
ospf
add action=set-priority chain=postrouting comment=\
"Translate DSCP Values into WMM priorities" new-priority=from-dscp \
passthrough=yes
/ip route
add distance=1 gateway=10.2.1.1 pref-src=10.2.1.4
/mpls interface
set [ find default=yes ] disabled=yes interface=ether10 mpls-mtu=1550
add interface=bridge1 mpls-mtu=1550
add interface=bonding2 mpls-mtu=1550
/mpls ldp
set enabled=yes lsr-id=10.1.255.51 transport-address=10.1.255.51
/mpls ldp interface
add interface=bridge1
add interface=bonding2
/routing ospf interface
add interface=loopback network-type=point-to-point passive=yes
add interface=bridge1 network-type=broadcast
add interface=bonding2 network-type=point-to-point use-bfd=yes
/routing ospf network
add area=area2 network=10.1.255.51/32
add area=area2 network=10.22.1.0/24
add area=area2 network=10.6.1.0/24
add area=area2 network=10.2.1.0/24
R2 config
Code: Select all
# nov/26/2021 12:10:32 by RouterOS 6.48.2
# model = RB4011iGS+
/interface bridge
add name=Loopback0
add name=bridge
/interface ethernet
set [ find default-name=ether1 ] comment=
set [ find default-name=ether2 ] comment=
set [ find default-name=ether3 ] comment=
set [ find default-name=ether4 ] comment=
set [ find default-name=ether5 ] comment=
set [ find default-name=ether6 ] comment=
set [ find default-name=ether9 ] comment="NetMetal"
set [ find default-name=ether10 ] comment="AirFiber" poe-out=forced-on
/interface bonding
add arp-ip-targets=10.1.255.51 link-monitoring=arp name=\
bonding1 slaves=ether9,ether10 transmit-hash-policy=layer-2-and-3
/interface ethernet switch port
set 0 default-vlan-id=0
set 1 default-vlan-id=0
set 2 default-vlan-id=0
set 3 default-vlan-id=0
set 4 default-vlan-id=0
set 5 default-vlan-id=0
set 6 default-vlan-id=0
set 7 default-vlan-id=0
set 8 default-vlan-id=0
set 9 default-vlan-id=0
set 10 default-vlan-id=0
set 11 default-vlan-id=0
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
/routing ospf area
set [ find default=yes ] disabled=yes
add area-id=2.2.2.2 default-cost=1 inject-summary-lsas=no name=area2 type=\
stub
/routing ospf instance
set [ find default=yes ] router-id=10.1.255.59
/interface bridge port
add bridge=bridge interface=ether1
add bridge=bridge interface=ether2
add bridge=bridge interface=ether6
add bridge=bridge interface=ether7
add bridge=bridge interface=ether8
/ip address
add address=10.2.2.2/27 interface=bridge network=10.2.2.0
add address=10.22.1.4/24 interface=bonding1 network=10.22.1.0
add address=10.6.1.4/24 interface=bonding1 network=10.6.1.0
add address=10.1.255.59 interface=Loopback0 network=10.1.255.59
/ip cloud
set update-time=no
/ip firewall mangle
add action=change-dscp chain=prerouting new-dscp=7 passthrough=no protocol=\
ospf
add action=set-priority chain=output new-priority=7 passthrough=yes protocol=\
ospf
add action=set-priority chain=postrouting comment=\
"Translate DSCP Values into WMM priorities" new-priority=from-dscp \
passthrough=yes
/ip route
add distance=1 gateway=10.2.2.1
/mpls interface
set [ find default=yes ] disabled=yes interface=ether4 mpls-mtu=1550
add interface=bridge mpls-mtu=1550
add interface=bonding1 mpls-mtu=1550
/mpls ldp
set enabled=yes lsr-id=10.1.255.59 transport-address=10.1.255.59
/mpls ldp interface
add interface=bridge
add interface=bonding1
/routing ospf interface
add interface=Loopback0 network-type=point-to-point passive=yes
add interface=bonding1 network-type=point-to-point use-bfd=yes
/routing ospf network
add area=area2 network=10.22.1.0/24
add area=area2 network=10.1.255.59/32
add area=area2 network=10.2.2.0/27
add area=area2 network=10.6.1.0/24
Code: Select all
/interface bridge
add name=bridge1
/interface wireless
set [ find default-name=wlan1 ] ampdu-priorities=0,1 antenna-gain=30 band=5ghz-onlyac basic-rates-a/g=24Mbps channel-width=20/40/80mhz-XXXX country=\
"" default-forwarding=no disabled=no frequency=5200 frequency-mode=superchannel ht-basic-mcs=mcs-8,mcs-9,mcs-10,mcs-11 ht-supported-mcs=\
mcs-8,mcs-9,mcs-10,mcs-11 installation=outdoor max-station-count=1 mode=ap-bridge multicast-helper=full nv2-cell-radius=28 nv2-downlink-ratio=70 \
rx-chains=0,1 scan-list=5200 ssid=Metal station-roaming=enabled supported-rates-a/g=24Mbps tdma-period-size=auto tx-chains=0,1 wireless-protocol=nv2 \
wmm-support=enabled
/interface ethernet
set [ find default-name=ether1 ] speed=100Mbps
/interface wireless nstreme
set wlan1 enable-nstreme=yes
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
set [ find default=yes ] addresses=0.0.0.0/0
/interface bridge port
add bridge=bridge1 interface=ether1
add bridge=bridge1 interface=wlan1
/ip address
add address=10.6.1.2/24 interface=bridge1 network=10.6.1.0
/ip firewall mangle
add action=change-dscp chain=prerouting new-dscp=7 passthrough=no protocol=ospf
add action=set-priority chain=output new-priority=7 passthrough=yes protocol=ospf
add action=set-priority chain=postrouting comment="Translate DSCP Values into WMM priorities" new-priority=from-dscp passthrough=yes
/ip route
add distance=1 gateway=10.6.1.1 pref-src=10.6.1.2 scope=10
Code: Select all
# model = 921UAGS-5SHPacD
/interface bridge
add name=bridge1
/interface wireless
set [ find default-name=wlan1 ] ampdu-priorities=0,1 antenna-gain=30 band=5ghz-onlyac basic-rates-a/g=24Mbps channel-width=20/40/80mhz-XXXX country=\
"" disabled=no distance=27 frequency=5200 frequency-mode=superchannel ht-basic-mcs=mcs-8,mcs-9,mcs-10,mcs-11 ht-supported-mcs=\
mcs-8,mcs-9,mcs-10,mcs-11 installation=outdoor mode=station-bridge multicast-helper=full rx-chains=0,1 scan-list=5200 ssid=BorMetal station-roaming=\
enabled supported-rates-a/g=24Mbps tx-chains=0,1 wireless-protocol=nv2
/interface ethernet
set [ find default-name=ether1 ] speed=100Mbps
/interface wireless nstreme
set wlan1 enable-nstreme=yes
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
/interface bridge port
add bridge=bridge1 interface=ether1
add bridge=bridge1 interface=wlan1
/ip address
add address=10.6.1.3/24 interface=bridge1 network=10.6.1.0
/ip firewall mangle
add action=change-dscp chain=prerouting new-dscp=7 passthrough=no protocol=ospf
add action=set-priority chain=output new-priority=7 passthrough=yes protocol=ospf
add action=set-priority chain=postrouting comment="Translate DSCP Values into WMM priorities" new-priority=from-dscp passthrough=yes
/ip route
add distance=1 gateway=10.6.1.1 pref-src=10.6.1.3 scope=10