Community discussions

MikroTik App
 
User avatar
emils
Forum Veteran
Forum Veteran
Topic Author
Posts: 906
Joined: Thu Dec 11, 2014 8:53 am

v7.1.1 is released!

Tue Dec 21, 2021 2:32 pm

RouterOS version 7.1.1 has been released "v7 stable" channel!

Before an upgrade:
1) Remember to make backup/export files before an upgrade and save them on another storage device;
2) Make sure the device will not lose power during upgrade process;
3) Device has enough free storage space for all RouterOS packages to be downloaded.

What's new in 7.1.1 (2021-Dec-21 13:53):

*) backup - added "force-v6-to-v7-configuration-upgrade" option on backup load to clear RouterOS v7 configuration and trigger reimport of RouterOS v6 route configuration (CLI only);
*) backup - fixed automatic backup generation when resetting configuration;
*) bgp - improvements on detecting peers local address when IPv6 link-local addresses are used;
*) capsman - improved system stability when processing CAP packet by Mangle;
*) dhcpv4-server - allow adding comments;
*) ethernet - improved system stability when receiving large packets on devices with 88F3720 CPU (nRAY, LHGG);
*) l3hw - fixed HW offloaded routing when using 7 or more VLAN interfaces;
*) l3hw - fixed bonding source MAC address;
*) l3hw - improved system stability when using 7 or more VLAN interfaces;
*) ntp - print log change time with time-zone applied;
*) ospf - fixed distance if "originate-default" is set to "always";
*) ospf - fixed neighbor stuck in ExStart;
*) ospf - fixed simple authentication;
*) ospf - improved overall stability;
*) ospf - improves stability when handling looped back OSPF packets;
*) upgrade - improved 404 error handling when checking for new versions;
*) webfig - fixed user policy lookup for skin designer;
*) winbox - made "Routing Filters/Rules" table sortable;
*) winbox - moved "IP/Route/Nexthops" and "IPv6/Route/Nexthops" menus to "Routing/Nexthops";
*) winbox - updated default "Routing/BGP/Peer Cache" table appearance;

To upgrade, click "Check for updates" at /system package in your RouterOS configuration interface, or head to our download page: http://www.mikrotik.com/download

If you experience version related issues, then please send supout file from your router to support@mikrotik.com. File must be generated while router is not working as suspected or after some problem has appeared on device

Please keep this forum topic strictly related to this particular RouterOS release.
 
User avatar
Ullinator
just joined
Posts: 8
Joined: Tue Jun 08, 2021 12:53 pm
Location: North-West Germany

Re: v7.1.1 is released!

Tue Dec 21, 2021 3:00 pm

Updated CRS326-24S+2Q+, 2x CRS328-24P-4S+, RB4011iGS+5Hac, 2x CRS326-24G-2S+, 4xCAP AC, 1 CAP XL AC successfull to 7.1.1 (ROS and FW) without problems.
I´ll keep an eye on any ROS problems.
 
russelld
just joined
Posts: 17
Joined: Mon Jan 29, 2018 2:58 am

Re: v7.1.1 is released!

Tue Dec 21, 2021 3:07 pm

So far I've upgraded the CCR1009-7G, CCR1009-8G and a hEX S all in my lab - all OK.

However, I would make the observation that after the upgrade to 7.1, my devices were still set to the "testing" channel, so when I hit "Download and Install" they initially started downloading 7.2rc1. I stopped them in time and switched the release channel back to stable.

Perhaps after an upgrade to 7.x, the release channel should be set to automatically default to "stable", to prevent inadvertent upgrades to release candidates?

R
 
User avatar
mrz
MikroTik Support
MikroTik Support
Posts: 7038
Joined: Wed Feb 07, 2007 12:45 pm
Location: Latvia
Contact:

Re: v7.1.1 is released!

Tue Dec 21, 2021 3:10 pm

release channel is whatever you have set. Default was always "stable".
 
leonardogyn
just joined
Posts: 18
Joined: Wed Dec 04, 2019 4:47 pm

Re: v7.1.1 is released!

Tue Dec 21, 2021 3:14 pm

not a word on the severe memory leak I reported on SUP-68885 :(
 
User avatar
Chupaka
Forum Guru
Forum Guru
Posts: 8709
Joined: Mon Jun 19, 2006 11:15 pm
Location: Minsk, Belarus
Contact:

Re: v7.1.1 is released!

Tue Dec 21, 2021 3:14 pm

And when upgrading from v6, you need to pick 'upgrade' channel, right? Looks like it falls back to stable
 
hecatae
Member Candidate
Member Candidate
Posts: 244
Joined: Thu May 21, 2020 2:34 pm

Re: v7.1.1 is released!

Tue Dec 21, 2021 3:24 pm

hAP ac2 successfully updated, both os and board firmware.
 
jookraw
Member Candidate
Member Candidate
Posts: 141
Joined: Mon Aug 19, 2019 3:06 pm

Re: v7.1.1 is released!

Tue Dec 21, 2021 3:47 pm

Wireguard IPv6 peer bug is still present... how hard is to check what changed from 7.1rc4?
 
User avatar
emils
Forum Veteran
Forum Veteran
Topic Author
Posts: 906
Joined: Thu Dec 11, 2014 8:53 am

Re: v7.1.1 is released!

Tue Dec 21, 2021 3:51 pm

And when upgrading from v6, you need to pick 'upgrade' channel, right? Looks like it falls back to stable
What do you mean exactly? Currently "upgrade" channel should show this 7.1.1 release.
Wireguard IPv6 peer bug is still present... how hard is to check what changed from 7.1rc4?
Should be fixed in 7.2rc1
 
User avatar
Chupaka
Forum Guru
Forum Guru
Posts: 8709
Joined: Mon Jun 19, 2006 11:15 pm
Location: Minsk, Belarus
Contact:

Re: v7.1.1 is released!

Tue Dec 21, 2021 3:55 pm

What do you mean exactly? Currently "upgrade" channel should show this 7.1.1 release.
I mean, 'testing' was an old way of upgrading from v6 to v7, now you need to use 'upgrade' channel. And there's no 'upgrade' in v7, so looks like everything works just like russelld expects, except he upgraded to v7 quite long time ago
 
User avatar
emils
Forum Veteran
Forum Veteran
Topic Author
Posts: 906
Joined: Thu Dec 11, 2014 8:53 am

Re: v7.1.1 is released!

Tue Dec 21, 2021 4:00 pm

I see. 7.1.1 is available in "testing" channel from v6 as well. So I get what russelld is talking about, but to be fair, when you update to "testing" channel, you still agree to install other "testing" versions as well, which 7.2rc2 is.
 
zainarbani
Frequent Visitor
Frequent Visitor
Posts: 54
Joined: Thu Jul 22, 2021 9:42 am
Location: Pati, Indonesia

Re: v7.1.1 is released!

Tue Dec 21, 2021 4:00 pm

Feature request: fetch via specific interface (curl --interface ...)
 
User avatar
pekr
Member Candidate
Member Candidate
Posts: 169
Joined: Tue Feb 22, 2005 9:05 pm
Location: Czech Republic
Contact:

Re: v7.1.1 is released!

Tue Dec 21, 2021 4:24 pm

Could changelog page tabs be sorted in the same manner, as the download section? It's confusing .....
 
soheilsh
Member Candidate
Member Candidate
Posts: 100
Joined: Fri Nov 26, 2010 3:39 pm

Re: v7.1.1 is released!

Tue Dec 21, 2021 4:32 pm

socks5 have problem in 7.1.1 , in 7.2rc1 is ok now
 
parham
Frequent Visitor
Frequent Visitor
Posts: 62
Joined: Sun Feb 15, 2015 11:35 pm

Re: v7.1.1 is released!

Tue Dec 21, 2021 4:40 pm

I can see the fix for LTE in 7.2rc1 "*) lte - fixed packet forwarding on R11e-4G and R11e-LTE-US;" but why is not in 7.1.1 which is the important fix.
 
User avatar
Halfeez92
Member Candidate
Member Candidate
Posts: 101
Joined: Tue Oct 30, 2012 12:58 pm
Location: 127.0.0.1
Contact:

Re: v7.1.1 is released!

Tue Dec 21, 2021 4:43 pm

Does v7 have UPS package?
 
User avatar
Ullinator
just joined
Posts: 8
Joined: Tue Jun 08, 2021 12:53 pm
Location: North-West Germany

Re: v7.1.1 is released!

Tue Dec 21, 2021 4:55 pm

Does v7 have UPS package?
No, I can´t find it anymore.
It was installed at 6.49.X but has gone with the update to 7.1.X
 
jookraw
Member Candidate
Member Candidate
Posts: 141
Joined: Mon Aug 19, 2019 3:06 pm

Re: v7.1.1 is released!

Tue Dec 21, 2021 5:06 pm

And when upgrading from v6, you need to pick 'upgrade' channel, right? Looks like it falls back to stable
What do you mean exactly? Currently "upgrade" channel should show this 7.1.1 release.
Wireguard IPv6 peer bug is still present... how hard is to check what changed from 7.1rc4?
Should be fixed in 7.2rc1
Just tested the 7.2rc1, not fixed
 
erlinden
Forum Guru
Forum Guru
Posts: 1900
Joined: Wed Jun 12, 2013 1:59 pm
Location: Netherlands

Re: v7.1.1 is released!

Tue Dec 21, 2021 5:21 pm

Does v7 have UPS package?
Will probably be part of future release. Didn't see it yet in any of the other 7.x releases (Dev/Test) as well.
 
User avatar
edielson_atm
Trainer
Trainer
Posts: 30
Joined: Tue May 29, 2007 5:23 am
Location: Brasilia - Brasil
Contact:

Re: v7.1.1 is released!

Tue Dec 21, 2021 5:42 pm

the "Remove Private AS" function in BGP is still not working
 
gotsprings
Forum Guru
Forum Guru
Posts: 2087
Joined: Mon May 14, 2012 9:30 pm

Re: v7.1.1 is released!

Tue Dec 21, 2021 6:23 pm

The RB3011 that I installed v7.1 now 7.1.1 still does not pass ARP discovery over zerotier.

I can connect to the Routerboard using the MAC address of the bridge. But not discover things on the other side.

RB3011 with 7.1Rc4 does.
hAP AC2 and Audience work regardless of 7.x version.
 
User avatar
rushlife
Member Candidate
Member Candidate
Posts: 243
Joined: Thu Nov 05, 2015 12:30 pm

Re: v7.1.1 is released!

Tue Dec 21, 2021 6:47 pm

update cannot be done on wsap ac, no enough of disk space :-(
 
User avatar
denisun
Frequent Visitor
Frequent Visitor
Posts: 81
Joined: Wed Jul 16, 2014 6:38 pm
Location: Greece

Re: v7.1.1 is released!

Tue Dec 21, 2021 7:06 pm

I still have problem with mark packet in ipv6.
When it is enable all traffic pass from input and drop to forward as invalid.
The connections show tab is empty.
When i disable mark packet, all work perfect but i have not QoS.
 
atakacs
Member Candidate
Member Candidate
Posts: 121
Joined: Mon Mar 07, 2016 5:39 pm

Re: v7.1.1 is released!

Tue Dec 21, 2021 7:32 pm

Any update / input / remark / comment on the IPSec issues lots of people are having ?
 
User avatar
eworm
Forum Guru
Forum Guru
Posts: 1070
Joined: Wed Oct 22, 2014 9:23 am
Location: Oberhausen, Germany
Contact:

Re: v7.1.1 is released!

Tue Dec 21, 2021 7:54 pm

Wireguard IPv6 peer bug is still present... how hard is to check what changed from 7.1rc4?
Should be fixed in 7.2rc1
Let's be more specific here, as we have two issues:

Wireguard interfaces did not receive a link local address, breaking at least OSPFv3. That is fixed now in 7.2rc1.
Please note that a link local address is assigned even if IPv6 is disabled (/ipv6 settings set disable-ipv6=yes). Looks like just another bug. 😜

Connecting several peers just leaves the last one touched with a functional IPv6 connection. I think this is what is still broken. (Did not yet test myself.)
This behavior is described in SUP-67181. Please have a look and fix this, it hurts me as well.
Last edited by eworm on Tue Dec 21, 2021 7:57 pm, edited 2 times in total.
 
User avatar
eworm
Forum Guru
Forum Guru
Posts: 1070
Joined: Wed Oct 22, 2014 9:23 am
Location: Oberhausen, Germany
Contact:

Re: v7.1.1 is released!

Tue Dec 21, 2021 7:55 pm

Any update / input / remark / comment on the IPSec issues lots of people are having ?
All my IPSec connections were down on a CCR1009... A reboot sorted this. No idea what happened, sadly I missed to generate a support output file.
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Tue Dec 21, 2021 8:17 pm

Upgraded my RB4011 from 7.1 to 7.1.1 and it appears to work ok, also IPsec.
There is an IPsec issue with statically configured /ip ipsec identity which disappears after reboot, but it turns out that already existed in 7.1
(after re-adding it manually from export made before the upgrade IPsec works OK for me)

I also tried upgrading to 7.2rc1 and it was a complete disaster, SUP-69560 created with the relevant info.
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Tue Dec 21, 2021 8:20 pm

I still have problem with mark packet in ipv6.
When it is enable all traffic pass from input and drop to forward as invalid.
The connections show tab is empty.
When i disable mark packet, all work perfect but i have not QoS.
I do use packet mark (based on DSCP value) and it appears to work for me.
 
templeos
just joined
Posts: 19
Joined: Mon Aug 26, 2019 3:58 pm

Re: v7.1.1 is released!

Tue Dec 21, 2021 8:42 pm

Graphs on WebFig with https still gives Error 404: Not Found like it did with v7.1.
 
User avatar
blackhandnz
just joined
Posts: 14
Joined: Mon Nov 29, 2021 11:41 pm
Location: New Zealand

Re: v7.1.1 is released!

Tue Dec 21, 2021 9:13 pm

Not sure if its a bug or not but after I upgraded from 7.1 to 7.1.1 some (70%) of my DHCP static lease entries got dropped (RB5009UG+S+)
 
truefriendcz
newbie
Posts: 39
Joined: Mon Jun 05, 2017 11:07 am

Re: v7.1.1 is released!

Wed Dec 22, 2021 12:48 am

In release v7.1.1 has been error this profile:
WAN as wlan2 with DHCP Client,... for better management i select wlan2 as "Bridge-Client", but ended with randomly error with connection timeouts.
On versions RouterOS v6.xx worked ok.

Problem (wanted solution):
Problem.png

Standard settings working ok (i am not wanted this solution):
AllOk.png
How i can fix this please?
You do not have the required permissions to view the files attached to this post.
Last edited by truefriendcz on Wed Dec 22, 2021 2:33 am, edited 1 time in total.
 
User avatar
afink
newbie
Posts: 34
Joined: Wed May 29, 2013 7:16 pm
Location: Basel & Freetown
Contact:

Re: v7.1.1 is released!

Wed Dec 22, 2021 1:03 am

Feature request: fetch via specific interface (curl --interface ...)
or fetch from a specific IP. Like a loopback while you use private IP's on the point to point links...
 
User avatar
afink
newbie
Posts: 34
Joined: Wed May 29, 2013 7:16 pm
Location: Basel & Freetown
Contact:

Re: v7.1.1 is released!

Wed Dec 22, 2021 1:07 am

Upgraded my RB4011 from 7.1 to 7.1.1 and it appears to work ok, also IPsec.
There is an IPsec issue with statically configured /ip ipsec identity which disappears after reboot, but it turns out that already existed in 7.1
(after re-adding it manually from export made before the upgrade IPsec works OK for me)
I have run into this multiple times. from 6.X to 7.1bet and from 7.1beta to 7.1 release I ended up with /ip ipsec identity being completely blank.
So if you have ipsec stuff, save your passwords. you probably will need them later...

The interesting thing was that on one router where I had issues after upgrade, i downgraded to release 6 and everything worked again.
So the identity config is not lost, its just hidden, disregarded in 7.
 
User avatar
npeca75
Frequent Visitor
Frequent Visitor
Posts: 75
Joined: Thu Aug 03, 2017 3:12 pm

Re: v7.1.1 is released!

Wed Dec 22, 2021 2:22 am

Connecting several peers just leaves the last one touched with a functional IPv6 connection. I think this is what is still broken. (Did not yet test myself.)
This behavior is described in SUP-67181. Please have a look and fix this, it hurts me as well.
+1
 
wojo
Frequent Visitor
Frequent Visitor
Posts: 85
Joined: Tue Aug 21, 2018 4:37 am

Re: v7.1.1 is released!

Wed Dec 22, 2021 3:15 am

This bricked my CCR1009-7G-1C-1S+ in a boot loop

I had to Netinstall and get back running on 7.1.1. Here's the serial console log, I tried everything including the backup boot loader but it always panics like this:
Could not mount ubifs/yaffs filesystem: No such device
[   10.000322] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000000
[   10.000437] CPU: 1 PID: 1 Comm: init Not tainted 5.6.3 #1
[   10.000494]   frame 0: __schedule+0x12288/0x7e0fb8 (sp 0xfffffe007a70fb20)
[   10.002498]   frame 1: __schedule+0x7bb290/0x7e0fb8 (sp 0xfffffe007a70fb90)
[   10.010159]   frame 2: __schedule+0x3ca50/0x7e0fb8 (sp 0xfffffe007a70fbc0)
[   10.017725]   frame 3: __schedule+0x40ca0/0x7e0fb8 (sp 0xfffffe007a70fc80)
[   10.025290]   frame 4: __schedule+0x431a8/0x7e0fb8 (sp 0xfffffe007a70fd20)
[   10.032856]   frame 5: __schedule+0x43270/0x7e0fb8 (sp 0xfffffe007a70fd60)
[   10.040422]   frame 6: __schedule+0x7de800/0x7e0fb8 (sp 0xfffffe007a70fd80)
[   10.048081]   <syscall 94 while in user mode>
[   10.052926]   frame 7: 0x45040 (sp 0x7f9cfb30)
[   10.057768] Rebooting in 5 seconds..
Resetting chip and restarting.
 logo.bmp not found or data is corrupted
 
wojo
Frequent Visitor
Frequent Visitor
Posts: 85
Joined: Tue Aug 21, 2018 4:37 am

Re: v7.1.1 is released!

Wed Dec 22, 2021 3:22 am

Looks like SD cards still do not mount on CCR1009-7G-1C-1S+, same on 7.2rc1.
 
User avatar
Halfeez92
Member Candidate
Member Candidate
Posts: 101
Joined: Tue Oct 30, 2012 12:58 pm
Location: 127.0.0.1
Contact:

Re: v7.1.1 is released!

Wed Dec 22, 2021 3:56 am

Still not fixed for DHCPv6-PD over VLAN PPPoE
 
manuek
just joined
Posts: 1
Joined: Sun Jan 03, 2021 7:51 am

Re: v7.1.1 is released!

Wed Dec 22, 2021 7:01 am

Rb4011 supports l3hw????
 
erlinden
Forum Guru
Forum Guru
Posts: 1900
Joined: Wed Jun 12, 2013 1:59 pm
Location: Netherlands

Re: v7.1.1 is released!

Wed Dec 22, 2021 7:15 am

How i can fix this please?
Why would you like to add an additional bridge that is not necessary?
What does your firewall (including NAT) look like?
 
User avatar
NAB
Trainer
Trainer
Posts: 542
Joined: Tue Feb 10, 2009 4:08 pm
Location: UK
Contact:

Re: v7.1.1 is released!

Wed Dec 22, 2021 10:05 am

Still seeing the same "kernel failure" problem on a CCR1009-8G-1S-1S+ every six hours or so under 7.1.1 as under 7.1.
Screenshot 2021-12-22 080425.png
You do not have the required permissions to view the files attached to this post.
 
accarda
Member Candidate
Member Candidate
Posts: 208
Joined: Fri Apr 05, 2019 4:06 pm
Location: Italy

Re: v7.1.1 is released!

Wed Dec 22, 2021 10:41 am

I have just tried to experiment with v7.1.1 using a hEX S router, which has a very basic config.
Started from Ros v6.49.2 and had only a mgmt VLAN interface, one bridge, loopback and a point to point ethernet connection to a rb4011 running 6.48.6.
With this basic i installed v7.1.1 and then I created a simple fresh (not ported from v6.49.2) BGP config to peer with rb4011.
Things worked fine on hEX S until when I tried to remove the default route (which was statically added by me) so that the default route from BGP was taking over.
This put BGP into open and not established.
I then tried to re-activate static default router from hEX S, but BGP session didn't restored.
I reboot hEX S and after that all ip/route and BGP config disappeared in winbox.
However main routes were there (but not visible neither Winbox or CLI) since I was still able to access hEX via VLAN and/or rb4011 ptp ethernet link.
When I tried to add a new BGP setting and so, after OK nothing appeared. Same as with adding new static route, nothing happened.
Switched back to Ros v6.49.2 and created there the same BGP config; all went OK.
Created supout file, but when I tried to file a case the form complained supout was not readable, so I couldn't file such report.
However from MK support site I was able to upload such rif file to supout viewer section and it's still there.

During these tests with v7.1.1 creating supout file took a long time; issuing an /export to check config over terminal didn't complete and the same when saving this to flash. However creating a backup file has worked. So something was not right with this installation on my unit.
Now everything is back to v6.49.2 and I will try again the same exercise later to see if I will get the same issues.

Armando
 
Nunak
just joined
Posts: 4
Joined: Tue Mar 20, 2012 10:56 am

Re: v7.1.1 is released!

Wed Dec 22, 2021 11:33 am

NTP server is still issue :( NTP server is responding only on one interface.
[admin@mikrotik.bla bla] > ip address/print 
Flags: X, I, D - DYNAMIC
Columns: ADDRESS, NETWORK, INTERFACE
 #   ADDRESS            NETWORK         INTERFACE                            
 0   192.168.1.1/24     192.168.1.0     br-vlan101                           
 1   192.168.2.1/24     192.168.2.0     br-vlan102                           
 2   10.128.63.1/24     10.128.63.0     br-vlan110                           
 3   192.168.11.1/24    192.168.11.0    br-vlan111                           
 4 X 84.242.114.116/29  84.242.114.112  ether1                               
 5   192.168.3.1/24     192.168.3.0     br-vlan103                           
 6   192.168.4.1/24     192.168.4.0     br-vlan104                           
 7   192.168.15.1/24    192.168.15.0    br-vlan115                           
 8   192.168.14.133/30  192.168.14.132  wireguard-bla
 9   192.168.14.137/30  192.168.14.136  wireguard-bla1     
10 I 192.168.14.141/30  192.168.14.140  wireguard-bla2     
11 D 192.168.99.145/24  192.168.99.0    ether1                               
12 D 192.168.14.123/32  192.168.14.124  <ovpn-1>                        
13 D 192.168.14.125/32  192.168.14.126  <ovpn-2>                        
14 D 192.168.14.121/32  192.168.14.122  <ovpn-3r>
(10:31:17)(193G) [root@raspberrypi-003:~] # /usr/lib/nagios/plugins/check_ntp_time -H 192.168.1.1
NTP OK: Offset -0.0007329285145 secs|offset=-0.000733s;60.000000;120.000000;
(10:31:28)(193G) [root@raspberrypi-003:~] # /usr/lib/nagios/plugins/check_ntp_time -H 192.168.11.1
NTP CRITICAL: No response from NTP server
Bug has been reported - SUP-69650
Last edited by Nunak on Wed Dec 22, 2021 1:01 pm, edited 2 times in total.
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Wed Dec 22, 2021 11:36 am

@accarda interesting that you see this issues, I had similar problems when upgrading from 7.1 to 7.2rc1 and I went to 7.1.1 and now it seems to work OK.
I created SUP-69560 for that, you may want to reference it when you make another SUP.

I thought it is an issue introduced in 7.2rc1 but apparently it can also happen in 7.1.1 and may be related to the actual config.
(I have 2 BGP templates and 7 BGP connections)
Last edited by pe1chl on Wed Dec 22, 2021 11:42 am, edited 1 time in total.
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Wed Dec 22, 2021 11:39 am

NTP server is still issue :( NTP server is responding only on one interface.
It works OK for me. Sure it is not a firewall issue?
I see some "funny behavior" of the NTP server, e.g. when I try to add an external server that happens to be already present as a dynamic server (obtained from DHCP) it goes bonkers. The new server is not accepted and another one is deleted.
But replying to requests seems to work OK here (I also have several networks).
 
accarda
Member Candidate
Member Candidate
Posts: 208
Joined: Fri Apr 05, 2019 4:06 pm
Location: Italy

Re: v7.1.1 is released!

Wed Dec 22, 2021 11:49 am

@pe1chl in my case I had this hEX-S running LT and never tried v7.x, so no possibility that some trace of v7 was in it.
Then I moved first to latest 6.49.2 just to make sure I had all with latest step before v7.
My move to v7.1.1 (first time) was all ok and BGP worked fine, even though after creating a template and then a connection I had to reboot the router to have it working fine (I have seen this on the forum that someone suggested reboot the device after the config).
But after that "I created an issue", there was no way to being able to edit, add routes or BGP config.
When I switched back to v6.49.2, no issue was ported back, BGP was not there (which I expected) and I was able to create my simple peer to rb4011. And in this case, repeated same exercise to disable static default route on hEX and it worked by enabling default route from BGP peer from rb4011.

So yes, definitively something went wrong in my case.
Even export resulted in std/io timeout (I saw it from supout reading over MK website viewer).
Last edited by accarda on Wed Dec 22, 2021 11:51 am, edited 3 times in total.
 
User avatar
afink
newbie
Posts: 34
Joined: Wed May 29, 2013 7:16 pm
Location: Basel & Freetown
Contact:

Re: v7.1.1 is released!

Wed Dec 22, 2021 11:49 am

I would like to report an issue with multiprotocol bgp, carrying both ipv4 and ipv6 af routes.
Tested this on wireguard interfaces, not sure about regular ethernet.
- when the session is ipv4-based: ipv4 routes work fine, and for ipv6 routes mikrotik builds ipv4-mapped ipv6 next-hop based on ipv4 interface address (eg ::ffff:192.168.0.1), ignoring interface ipv6 address set explicitly.
- when the session is ipv6-based: ipv6 routes work fine, and for ipv4 routes mikrotik puts 0.0.0.0 as next-hop.

so there is no option to run both v4 and v6 in one bgp session.
I would recommend running a BGP session for IPv4 and one for IPv6. With the many peerings I have over dozens of Internet exchanges, I have not seen a single peer which uses BGP with IPv4 not in a separate session from BGP with IPv6. So it's kind of the standard way of doing it.
 
poirus
just joined
Posts: 1
Joined: Thu Dec 09, 2021 8:31 am

Re: v7.1.1 is released!

Wed Dec 22, 2021 12:23 pm

How to use force-v6-to-v7-configuration-upgrade, geve an example please
/system/backup/load name=BackupNameFile.backup force-v6-to-v7-configuration-upgrade=yes
Last edited by poirus on Wed Dec 22, 2021 12:31 pm, edited 1 time in total.
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Wed Dec 22, 2021 12:39 pm

@pe1chl in my case I had this hEX-S running LT and never tried v7.x, so no possibility that some trace of v7 was in it.
Unfortunately the "modern devices" are not ideal to experiment with versions. It may be easier to try a classic one (RB2011, old hEX) or a higher end modern one (RB3011,RB4011) because they have enough flash space to have two or more versions on the router at the same time (partitioning).
I use that to try upgrades and switch back when it does not work. At the moment I have 7.1 and 7.1.1 on my router (running 7.1.1) and I am ready to try 7.2rc versions by just copying the 7.1.1 over the 7.1 install and then upgrade it, when it fails I can switch to the copy.
What you describe is a lot like what I experienced by upgrading an existing working installation from 7.1 to 7.2rc1.
IP route screen is empty, /ip route print command hangs, /export command hangs, create supout.rif takes a very long time.
But with 7.1.1 it is all OK for me. Strange.
 
Nunak
just joined
Posts: 4
Joined: Tue Mar 20, 2012 10:56 am

Re: v7.1.1 is released!

Wed Dec 22, 2021 1:04 pm

NTP server is still issue :( NTP server is responding only on one interface.
It works OK for me. Sure it is not a firewall issue?
I see some "funny behavior" of the NTP server, e.g. when I try to add an external server that happens to be already present as a dynamic server (obtained from DHCP) it goes bonkers. The new server is not accepted and another one is deleted.
But replying to requests seems to work OK here (I also have several networks).
Yes this was working on ROS6 I wasn't changing any FW rules and I have this issue on all ROS7 boxes.
 
truefriendcz
newbie
Posts: 39
Joined: Mon Jun 05, 2017 11:07 am

Re: v7.1.1 is released!

Wed Dec 22, 2021 1:07 pm

How i can fix this please?
Why would you like to add an additional bridge that is not necessary?
What does your firewall (including NAT) look like?
It is default config after reset router and change to add bridge-Client and change other params on the screen for acessing to internet.
 
poirus
just joined
Posts: 1
Joined: Thu Dec 09, 2021 8:31 am

Re: v7.1.1 is released!

Wed Dec 22, 2021 1:11 pm

4011 loop reboot after upgrade from 6.49.2 every 2-5 min. At one moment 1 core was 100% load for a minute and reboot again. Disable 2 IPIP tunnels to mikrotik 6.49.2 solved the problem. But I need them, so problem is somewhere in it.
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Wed Dec 22, 2021 1:16 pm

Yes this was working on ROS6 I wasn't changing any FW rules and I have this issue on all ROS7 boxes.
Interesting. I checked again and for me it works fine.
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Wed Dec 22, 2021 1:19 pm

Disable 2 IPIP tunnels to mikrotik 6.49.2 solved the problem. But I need them, so problem is somewhere in it.
Are you sure the IPIP tunnels are not somehow looping (tunnel traffic routed back into the tunnel instead of to internet)?
Maybe this is caused by some of the routing changes in v7, e.g. in "scope" and "target scope", or selecting active route.
 
ghostt
just joined
Posts: 21
Joined: Tue Apr 24, 2018 4:07 pm
Location: Australia

Re: v7.1.1 is released!

Wed Dec 22, 2021 1:41 pm

Upgraded CCR1036-12G-4S to v7.1.1. Latest Winbox version is used. First impressions, well...
1. OSPF between this router and another CCR v6.49.2 had stopped working. With a quick look I couldn't determine where the problem was...
2. Routing Filters didn't appear in the "classic" way in Winbox, they were looking more like scripts, not very user friendly, especially when it was impossible to look through the options any more.
3. Couldn't find Routing BGP Networks. BGB still seamed to continue working but I couldn't find where the networks and aggregations gone, sorry.
4. Periodically Winbox windows didn't show the contents, for example, going to IP Routes. But there was nothing shown in the window, no list of the existing routes, although routes did exist as I could ping some of my customers (those ones that were running over BGP), restart Winbox didn't help. Reboot the router helped. But the problem appeared again after running Winbox for a while. The same was with Routing Filters.
5. IP Routes. I've got a large network of VPNs to our clients with BGP running over it. The routes dynamically created by BGP didn't show the tunnel name next to the gateway any more, although in v6.49.2 they did. For example, 10.10.10.0/29 Gateway 10.0.0.3 <sstp-client2> reachable. <sstp-client2> wasn't shown, only gateway 10.0.0.3 could be seen. But it would be very handy to know what VPN tunnel is actually providing gateway 10.0.0.3.
These are the most important issues, well for me at least. There were some others, but sorry, I didn't pay much attention to them being overwhelmed with customers' phone calls.

Bottom line. I've rolled back to v6.49.2 using Netinstall, as the router didn't "want" doing that any other way :) No logs or screenshots were taken due to the customer pressure, sorry.

That upgrade had been done on the working in the field router on purpose to see the real-life effects. After that I've disabled all automatic upgrades for all of my customers plus 7 core CCR routers forming our backbone network. I guess, the questions would be:

- Would you recommend to stay on v6.xxxx?
- If not, is there an easy way to move to v7.xxxx?
- Are there any field examples for OSPF and BGP, including filters and routes for v7xxxx?

All above wasn't a complaint, just a feedback from the field :)

Thanks guys.

P.S. Chupaka, is there a way to contact you, i.e. email? :)
 
User avatar
mrz
MikroTik Support
MikroTik Support
Posts: 7038
Joined: Wed Feb 07, 2007 12:45 pm
Location: Latvia
Contact:

Re: v7.1.1 is released!

Wed Dec 22, 2021 1:53 pm

2.,3) https://help.mikrotik.com/docs/display/ ... figuration
5.) set Winbox to show appropriate parameter "immediate-gateway", "gateway" is configurable parameter and will not show runtime info
 
ghostt
just joined
Posts: 21
Joined: Tue Apr 24, 2018 4:07 pm
Location: Australia

Re: v7.1.1 is released!

Wed Dec 22, 2021 2:17 pm

mrz,
Thank you. I did try "immediate-gateway", "gateway". something like <sstp-client1> didn't appear in the corresponding columns. They were just blank or "unknown". I'll try your suggestion for 2 and 3, thank you but on a test router this time, sorry. BTW, after posting here I've spoken to one of my colleagues who uses and loves Mikrotiks, he is also one of carrier ISPs in Australia. His exact words were "stay on v6"; problems - OSPF/BGP.

Plus an opinion of a person who uses Mikrotiks all the time. No matter how big the difference is between versions of an upgrade an the latest running one, the upgrade procedure should not brake anything (in theory).
 
ksuuk
Frequent Visitor
Frequent Visitor
Posts: 91
Joined: Wed Jan 22, 2014 5:11 pm

Re: v7.1.1 is released!

Wed Dec 22, 2021 2:27 pm

Updated 4xCAP AC, 1 CAP XL AC successfull to 7.1.1 (ROS and FW) without problems.
How did You upgrade 16 MB device, which is having only few MB free space, with the 12,9 MB image?

At least I got error - "not enough space for upgrade".
Last edited by ksuuk on Wed Dec 22, 2021 4:33 pm, edited 1 time in total.
 
andacb
just joined
Posts: 2
Joined: Thu Apr 15, 2021 1:03 pm

Re: v7.1.1 is released!

Wed Dec 22, 2021 2:39 pm

Is the Dude server coming to this version? Or which version will it be included in v7.x series?
 
russelld
just joined
Posts: 17
Joined: Mon Jan 29, 2018 2:58 am

Re: v7.1.1 is released!

Wed Dec 22, 2021 2:43 pm

I see. 7.1.1 is available in "testing" channel from v6 as well. So I get what russelld is talking about, but to be fair, when you update to "testing" channel, you still agree to install other "testing" versions as well, which 7.2rc2 is.
I may have upgraded one of the devices using the 'testing' channel, but I'm pretty sure I used the 'upgrade' channel for the other devices. I did a further upgrade to a CRS317, RB3011 and RB4011. One of those was also left on the 'testing' channel, whilst the other two remained set to the 'stable' channel. I have never installed anything from the development channel and had never installed any 7.x pre-release - so it was a direct upgrade from 6.48.x or 6.49.x.

Either way: if 7.1 was available via the 'testing' channel as well as the 'upgrade' channel, given the significance of this upgrade, it would seem prudent to revert to default of 'stable' after an upgrade from a 6.x release... Just my opinion!

Thanks for all the work on v7 so far - never had the time to play with pre-release versions of 7.x, but now that it is 'stable' (with a full understanding of what that means in Mikrotik world) I'm looking forward to seeing what it has to offer and I'm also looking forward to the new hardware the updated kernel will unlock in the coming year (even with the chip shortage....)
 
accarda
Member Candidate
Member Candidate
Posts: 208
Joined: Fri Apr 05, 2019 4:06 pm
Location: Italy

Re: v7.1.1 is released!

Wed Dec 22, 2021 3:34 pm

@pe1chl just for the sake of completing this, I have repeated again the same setup and steps, starting "almost" fresh from v6.49.2.
In fact before making the first move to v7.1.1 I had created a backup for v6.49.2, which never included any trace of v7.1.1, which resulted in a clean starting point for me.

So after moving back to v6.49.2 and restored from such backup, I went again v7.1.1 and this time all menu were ok and filled with data.
I have recreated again BGP peer to rb4011 and got the same network being distributed.
Since I receive default route also from rb4011, this time when I disabled the local default route, it worked fine and activated the one from BGP.
The first time when I created BGP I didn't set the AFI option (didn't know it before), but added it once I saw some warning in the log complaining about missing AFI settings.
Then, I tried to disable the default route and the whole issue began.
This time when I created template I have set AFI before the BGP instance was started and no problem at all.
It might not have anything to deal with, but this is something different that I did this time (knowing my previous mistake).

I will have to read and learn little bit more about this new BGP implementation in Ros v7 to play with, but during first attempt I have noticed with profile an usage of 90% CPU on one core (while winbox indicated overall CPU around 25%), while now everything is low usage 0%.
Not sure whether hEX S was in a bad status at that moment and hit CPU so bad (may be export not working etc was associated to this).
Will see in the next days how it's still running.
 
hecatae
Member Candidate
Member Candidate
Posts: 244
Joined: Thu May 21, 2020 2:34 pm

Re: v7.1.1 is released!

Wed Dec 22, 2021 3:35 pm

4011 loop reboot after upgrade from 6.49.2 every 2-5 min. At one moment 1 core was 100% load for a minute and reboot again. Disable 2 IPIP tunnels to mikrotik 6.49.2 solved the problem. But I need them, so problem is somewhere in it.
Have you updated the routerboard firmware?
 
w0lt
Long time Member
Long time Member
Posts: 537
Joined: Wed Apr 02, 2008 2:12 pm
Location: Minnesota USA

Re: v7.1.1 is released!

Wed Dec 22, 2021 3:37 pm

Has anyone gotten the “ChangeIP DynDNS” script to work in ROS 7.x yet ?

-tp
 
User avatar
Ullinator
just joined
Posts: 8
Joined: Tue Jun 08, 2021 12:53 pm
Location: North-West Germany

Re: v7.1.1 is released!

Wed Dec 22, 2021 3:40 pm

Updated 4xCAP AC, 1 CAP XL AC successfull to 7.1.1 (ROS and FW) without problems.
How did You upgrade 16 MB device, which is having only few MB free space, with the 12,9 MB image?
@ksuuk: It was done automaticaly via CAPsMAN (which is my RB4011iGS+5HacQ2HnD) after I´ve upgraded this device to 7.1.1
hc_086.jpg
I didn´t tried it in another way.. :-/
You do not have the required permissions to view the files attached to this post.
 
netbus
Frequent Visitor
Frequent Visitor
Posts: 60
Joined: Mon Sep 04, 2017 12:42 pm

Re: v7.1.1 is released!

Wed Dec 22, 2021 3:51 pm

IPv6 Firewall Connection Tracking is still not available on HAP ac²
 
User avatar
eworm
Forum Guru
Forum Guru
Posts: 1070
Joined: Wed Oct 22, 2014 9:23 am
Location: Oberhausen, Germany
Contact:

Re: v7.1.1 is released!

Wed Dec 22, 2021 4:00 pm

IPv6 Firewall Connection Tracking is still not available on HAP ac²
You are using queues, no? This is a known issue, at lease here in the forum. (I hope Mikrotik is aware...)
SUP-69071
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Wed Dec 22, 2021 4:43 pm

Upgraded CCR1036-12G-4S to v7.1.1. Latest Winbox version is used. First impressions, well...
2. Routing Filters didn't appear in the "classic" way in Winbox, they were looking more like scripts, not very user friendly, especially when it was impossible to look through the options any more.
3. Couldn't find Routing BGP Networks. BGB still seamed to continue working but I couldn't find where the networks and aggregations gone, sorry.
These are not release specific issues, you are describing common suprises people will have when migrating from v6 to v7. You will have to re-learn a few things.
(and also the BGP implementation is not complete)

See the documentation on help.mikrotik.com
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Wed Dec 22, 2021 4:53 pm

I have run into this multiple times. from 6.X to 7.1bet and from 7.1beta to 7.1 release I ended up with /ip ipsec identity being completely blank.
So if you have ipsec stuff, save your passwords. you probably will need them later...
Of course I always make a backup and export before upgrades. And I have read a couple of times about loss of config. So after an upgrade I do a new export and diff them, to see what I might have lost in the process. That had already alerted me about problems before, especially in the config conversion.
(of course remember to add show-sensitive parameter when doing export in v7)
In this case I was alerted by the repeated "initiator can't find identity for peer: xxxx" messages in the log window, while that identity should exist.
The interesting thing was that on one router where I had issues after upgrade, i downgraded to release 6 and everything worked again.
So the identity config is not lost, its just hidden, disregarded in 7.
Well you have to understand how it works internally: all the config info you see in /export is stored in a "database". That is what /system backup saves.
There is a separate database for v6 and v7. When you upgrade from v6 to v7 the database is converted by a program called "crossfig", this only happens on your first upgrade.
When you downgrade, you fall back to the old v6 database. So what you see there is unaffected by what happened under v7 (also all changes you made).
Somewhat surprising, when you later upgrade from v6 to v7 again, there is no new conversion. So you get the config that was present in the past when you first converted to v7! It had been sleeping all the time you used v6. The new improvements in crossfig or the new v7 release you use now are ignored.
There appears to be no way to delete that v7 database under v6. And when you backup under v6, both databases will be in your backup, so restoring that does not help either.

Only in this version a new flag has been added to the backup load command to ignore the v7 database, load the v6 database, and convert it again using the current version of crossfig. So probably when you have repeatedly tried to upgrade and then decided to downgrade, the best thing is to backup and then restore using that flag.

On my router, at one point I decided to export, reset to blank configuration, and import the configuration again, just to be sure there is no crap like that left.
(which then shows bugs in the export file, which still have not been fixed. but that is another matter)
 
User avatar
AshuGite
just joined
Posts: 13
Joined: Sat Jul 09, 2016 8:31 pm
Location: India
Contact:

Re: v7.1.1 is released!

Wed Dec 22, 2021 5:12 pm

CCR2004-16G-2S+ Switch2 all ports are flapping at same time..
 
netbus
Frequent Visitor
Frequent Visitor
Posts: 60
Joined: Mon Sep 04, 2017 12:42 pm

Re: v7.1.1 is released!

Wed Dec 22, 2021 5:48 pm

You are using queues, no? This is a known issue, at lease here in the forum. (I hope Mikrotik is aware...)
SUP-69071
Yes I use simple queue.
Does it mean there is a workaround for it? Disabling Queues?
 
User avatar
eworm
Forum Guru
Forum Guru
Posts: 1070
Joined: Wed Oct 22, 2014 9:23 am
Location: Oberhausen, Germany
Contact:

Re: v7.1.1 is released!

Wed Dec 22, 2021 6:19 pm

Yes, ipv6 connection tracking works if you disable queues. Well, just make sure the ipv6 traffic does not go through a queue.
 
mafiosa
Member Candidate
Member Candidate
Posts: 266
Joined: Fri Dec 09, 2016 8:10 pm
Location: Kolkata, India
Contact:

Re: v7.1.1 is released!

Wed Dec 22, 2021 6:43 pm

Please help me with high CPU usage with PCC Loadbalancing on RB3011 v7.1.1 viewtopic.php?t=181516
 
BRMateus2
Frequent Visitor
Frequent Visitor
Posts: 73
Joined: Thu Oct 26, 2017 11:18 pm

Re: v7.1.1 is released!

Wed Dec 22, 2021 6:50 pm

Upgraded mipsbe RB951G from v6 to v7 and worked fine at the first moment, but when I upgraded the firmware it broke the router, now its DHCP doesn't work and the router can't handle any Layer 3 IP IPv6 anymore - will try to netinstall with a switch in between, because directly connecting to PC for netinstall doesn't work either, and every time I connect by MAC, I get disconnected 1 second after, even with my config or defaults.
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Wed Dec 22, 2021 7:29 pm

It is always a bit tricky to know of your problem is caused by "upgrading the firmware" or by "rebooting because firmware upgraded".
Unfortunately there are still some v7 bugs that manifest only after a reboot.
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Wed Dec 22, 2021 7:30 pm

Yes, ipv6 connection tracking works if you disable queues. Well, just make sure the ipv6 traffic does not go through a queue.
Ipv6 works for me with a queue tree (and packet marking based on DSCP). Probably you mean a simple queue?
 
2bn2t
just joined
Posts: 17
Joined: Fri Jul 09, 2021 11:17 am

BootLoop from 7.1 on CCR1009-7G and several hAP ac2

Wed Dec 22, 2021 7:39 pm

Just tried to update and every device ended up in a BootLoop…
 
johnson73
Member Candidate
Member Candidate
Posts: 172
Joined: Wed Feb 05, 2020 10:07 am

Re: v7.1.1 is released!

Wed Dec 22, 2021 8:12 pm

Upgrade 7.1.1 vers. wAP Ac (architecture mipsbe). There are still problems with Upload speed. This is critically low. There was no such problem with version 6.49.2!
 
User avatar
eworm
Forum Guru
Forum Guru
Posts: 1070
Joined: Wed Oct 22, 2014 9:23 am
Location: Oberhausen, Germany
Contact:

Re: v7.1.1 is released!

Wed Dec 22, 2021 8:40 pm

Ipv6 works for me with a queue tree (and packet marking based on DSCP). Probably you mean a simple queue?
I have simple queues with pcq, yes.
 
khialb32
newbie
Posts: 38
Joined: Wed Aug 09, 2017 1:17 am

Re: v7.1.1 is released!

Wed Dec 22, 2021 10:14 pm

still, no fix to the 404 error on Hotspot web page that comes from time to time!
 
DL7JP
Frequent Visitor
Frequent Visitor
Posts: 85
Joined: Sat Oct 19, 2013 4:14 pm

Re: v7.1.1 is released!

Thu Dec 23, 2021 1:14 am

Hi,
I updated a RB1100AHx4 from 6.49.2 to 7.1 then 7.1.1 and ended up in a strange situation: The router works fine, but asa I reboot it all is screwed up: All bridges are gone, so all IPs are missing, no access via MAC-Telnet. After resetting it and restoring the 7.1 backup with 7.1.1 all works fine again, but a reboot srews it all up.
Any suggestions how I coud fix this situation besides downgrading to 6.49.2 and waiting for a more stable 7.x Version?
- Joachim.
 
ghostt
just joined
Posts: 21
Joined: Tue Apr 24, 2018 4:07 pm
Location: Australia

Re: v7.1.1 is released!

Thu Dec 23, 2021 1:21 am

you are describing common suprises people will have when migrating from v6 to v7. You will have to re-learn a few things.
(and also the BGP implementation is not complete)

See the documentation on help.mikrotik.com
Thank you for your answer. That is exactly what I'm talking about with the exception I wouldn't call that surprises, I'd call that "problems", as nothing currently working should stop doing so with an upgrade. No one is against re-leaning something nor I said your product is bad. As I said that wasn't a complaint but a feedback from the Mikrotik users in a commercial environment not in a lab where everything is working. I'd love to migrate (and I've tried to do so) but simple migration from v6 to v7 doesn't work and overall, it looks like v7 is still a "test" version, which has issues even with Winbox.
 
ghostt
just joined
Posts: 21
Joined: Tue Apr 24, 2018 4:07 pm
Location: Australia

Re: v7.1.1 is released!

Thu Dec 23, 2021 1:24 am

Hi,
I updated a RB1100AHx4 from 6.49.2 to 7.1 then 7.1.1 and ended up in a strange situation: The router works fine, but asa I reboot it all is screwed up: All bridges are gone, so all IPs are missing, no access via MAC-Telnet. After resetting it and restoring the 7.1 backup with 7.1.1 all works fine again, but a reboot srews it all up.
Any suggestions how I coud fix this situation besides downgrading to 6.49.2 and waiting for a more stable 7.x Version?
- Joachim.
Welcome to the club :) Quick fix is downgrading, sorry. I had to do the same, so waiting for 7.x.x version, which works.
 
User avatar
nichky
Forum Guru
Forum Guru
Posts: 1275
Joined: Tue Jun 23, 2015 2:35 pm

Re: v7.1.1 is released!

Thu Dec 23, 2021 4:19 am

romon doesn't work btw v6 and v7
 
ghostt
just joined
Posts: 21
Joined: Tue Apr 24, 2018 4:07 pm
Location: Australia

Re: v7.1.1 is released!

Thu Dec 23, 2021 4:43 am

mrz,
Thank you again for that. I think I've figured out why OSPF gone broken on migration from v6 to v7. Maybe someone will find it handy. It looks like Mikrotik has converted networks in v6:
/routing ospf network
add area=backbone network=1.1.1.0/29
Into Interface templates, exactly how it is written in the help document you sent me:
/routing ospf interface-template
add network=1.1.1.0/29 area=backbone_v2
May be it will work between versions 7, I haven't check yet. But it doesn't work between CCR v6 and CCR v7. OSPF started working after I've programmed interface-templates like that:
/routing ospf interface-template
add area=backbone_v2 prefix-list=1.1.1.0/29
Just a thought. I would be very handy if Routing-Filters if adding via Winbox, not terminal, still had those tabs and clickable options like in v6, and then upon pressing "Apply" or "OK" the filter would be converted to a script. :)
 
User avatar
Jotne
Forum Guru
Forum Guru
Posts: 3279
Joined: Sat Dec 24, 2016 11:17 am
Location: Magrathean

Re: v7.1.1 is released!

Thu Dec 23, 2021 8:16 am

romon doesn't work btw v6 and v7
Connect Rommon -> RB750Gr3 6.48.4 -> Rommon to SXT 5HPnDr2 7.2rc1 OK
Connect Rommon -> RB750Gr3 6.48.4 -> Rommon to CHR 7.1 OK
Connect Rommon -> RB750Gr3 6.48.4 -> Rommon to CHR 7.2rc1 OK

Connect Rommon -> SXT 5HPnDr2 7.2rc1 -> Rommon to RB750Gr3 6.48.4 OK
Connect Rommon to CHR 7.1 -> Rommon -> RB750Gr3 6.48.4 OK

So no problem. Have you enabled Rommon?
 
accarda
Member Candidate
Member Candidate
Posts: 208
Joined: Fri Apr 05, 2019 4:06 pm
Location: Italy

Re: v7.1.1 is released!

Thu Dec 23, 2021 8:49 am

romon doesn't work btw v6 and v7
I have only 1 router migrated to v7.1.1, but either if I set RoMON agent to be one of v6 or the v7 router, I can log into all the others with no issues, including the v7 one.
 
jimint
just joined
Posts: 18
Joined: Fri Aug 11, 2017 12:58 am

Re: v7.1.1 is released!

Thu Dec 23, 2021 8:55 am

I suggest about wireguard to include a button which generate qrcode for clients. It will be very easy because now we send always the keys with our emails.
 
jamsden
newbie
Posts: 25
Joined: Fri Feb 26, 2021 7:28 am

Re: v7.1.1 is released!

Thu Dec 23, 2021 9:35 am

Welcome to the club :) Quick fix is downgrading, sorry. I had to do the same, so waiting for 7.x.x version, which works.
I’ll keep 6.48.6, thanks for sharing.
 
LordRob
just joined
Posts: 2
Joined: Mon Mar 07, 2016 11:03 pm

Re: v7.1.1 is released!

Thu Dec 23, 2021 10:05 am

I upgraded my RB3011UiAS to v7.1.1.Also the dude client is upgraded to v7.1.1 on a Windows10 PC. However after the upgrade the Dude client does not start. The Windows Task Manager does not show a running Dude program or process. It seems the Dude package is not part of this release. it does not show up in the package list of the device.
On the same PC Winbox64 v3.31 is running and this application is able to connect with the RB3011UiAS. Does anyone have a suggestion for me?
 
truefriendcz
newbie
Posts: 39
Joined: Mon Jun 05, 2017 11:07 am

Re: v7.1.1 is released!

Thu Dec 23, 2021 11:40 am

Why is version 7.1.1 still released as stable when it has quite a many issues?
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Thu Dec 23, 2021 11:44 am

As I said that wasn't a complaint but a feedback from the Mikrotik users in a commercial environment not in a lab where everything is working. I'd love to migrate (and I've tried to do so) but simple migration from v6 to v7 doesn't work and overall, it looks like v7 is still a "test" version, which has issues even with Winbox.
You are right, RouterOS v7 is not ready for production in cases where BGP or OSPF is involved. MikroTik is pushing it as "stable" and that suggests to some people that it is stable and reliable software, but it isn't complete. You certainly cannot migrate a BGP setup from v6 to v7 without problems yet.

But remember, when e.g. Microsoft releases a new Windows version, they also promote it as the best thing ever and the most stable ever, while many users will face difficulties in their particular usage scenario. Things there software relies on that are no longer supported, new bugs, irritating new features they did not ask for.
With RouterOS it is the same. And similar to Windows versions, it helps to wait a while for the initial problems to be ironed out. There still will be problems left, but at least there will be fewer unintended omissions.
(I assume MikroTik will still implement BFD, Aggregation, a well-working connection status display, etc etc. Until that, it is not usable in production for me)
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Thu Dec 23, 2021 11:48 am

Why is version 7.1.1 still released as stable when it has quite a many issues?
I think because
- there is more and more hardware which only supports v7 and requires a "stable" OS.
- when not moving large numbers of users over to v7, many of the issues will not be found and will still appear later when the move is made.

Depending on your usage, v7 can work quite well. Or you may encounter bugs and omissions. The experience will not be the same for everyone.
E.g. on my hAP ac2 that I run only as a WiFi AP in bridge mode, v7.2rc1 works without issue.
On my RB4011 that works as a router using lots of features, I can use 7.1.1 but not 7.2rc1 (it has too many issues). With 7.1.1 I have to work around problems, but it runs without crashing.
 
DL7JP
Frequent Visitor
Frequent Visitor
Posts: 85
Joined: Sat Oct 19, 2013 4:14 pm

Re: v7.1.1 is released!

Thu Dec 23, 2021 3:13 pm

Hi,
I updated a RB1100AHx4 from 6.49.2 to 7.1 then 7.1.1 and ended up in a strange situation: The router works fine, but asa I reboot it all is screwed up: All bridges are gone, so all IPs are missing, no access via MAC-Telnet. After resetting it and restoring the 7.1 backup with 7.1.1 all works fine again, but a reboot srews it all up.
Any suggestions how I coud fix this situation besides downgrading to 6.49.2 and waiting for a more stable 7.x Version?
- Joachim.
Welcome to the club :) Quick fix is downgrading, sorry. I had to do the same, so waiting for 7.x.x version, which works.
Rather than downgrading (I need wireguard), I restored the 7.1 backup again under 7.1.1, then I deactived and in turn activated all interfaces and bridges. Now I can reboot.
All this is a bit suspicious, I will see how stable it is.
 
User avatar
Chaosphere64
Frequent Visitor
Frequent Visitor
Posts: 94
Joined: Wed Aug 10, 2016 10:19 pm

Re: v7.1.1 is released!

Thu Dec 23, 2021 3:30 pm

I had a rough patch when upgrading my RB4011 from RouterOS 6.49.2, too. Uninstalled extra packages, upgraded to 7.x, reboot, no problem. Saved 7.x backup and rsc to my computer. After firmware upgrade the device rendered unusable. IP addresses were gone, no access even when trying a L2 connection while being directly connected to the device. I netinstalled it, upgraded RouterOS, reset config, rebooted, upgraded firmware, reboot without config. Now the device was working with default settings. I tried to restore the 7.x backup which worked.

I reached my goal and RouterOS 7.x works now, but the process was not very pleasant and surely not something that will scale well ...
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Thu Dec 23, 2021 3:57 pm

I reached my goal and RouterOS 7.x works now, but the process was not very pleasant and surely not something that will scale well ...
Well, that is now the main elephant in the room. We have many routers on remote locations (difficult physical access) and we really need bullet-proof upgrade procedures that never result in bricked devices or bootloops, or other failures that result in problems remotely accessing the device (including BGP migration).
Before we are in that situation, we need to remain at v6.
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 26289
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: v7.1.1 is released!

Thu Dec 23, 2021 4:17 pm

Unless you require something very specific from v7 in all your devices, you can safely stay on latest v6, it is secure and stable. There is no need to do mass upgrades to v7. You can simply upgrade over time, or introduce v7 only when adding new devices.
 
User avatar
Halfeez92
Member Candidate
Member Candidate
Posts: 101
Joined: Tue Oct 30, 2012 12:58 pm
Location: 127.0.0.1
Contact:

Re: v7.1.1 is released!

Thu Dec 23, 2021 4:34 pm

Unless you require something very specific from v7 in all your devices, you can safely stay on latest v6, it is secure and stable. There is no need to do mass upgrades to v7. You can simply upgrade over time, or introduce v7 only when adding new devices.
If only RB5009 can use v6! I would not care if v7 got bugs or not.
 
buset1974
Frequent Visitor
Frequent Visitor
Posts: 86
Joined: Wed Sep 13, 2006 12:12 pm
Location: Jakarta

Re: v7.1.1 is released!

Thu Dec 23, 2021 5:42 pm

when the routing/bgp/session prefix count will be fixed?
or maybe you think that it's not so important?
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 26289
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: v7.1.1 is released!

Thu Dec 23, 2021 10:40 pm

Unless you require something very specific from v7 in all your devices, you can safely stay on latest v6, it is secure and stable. There is no need to do mass upgrades to v7. You can simply upgrade over time, or introduce v7 only when adding new devices.
If only RB5009 can use v6! I would not care if v7 got bugs or not.
I was answering about difficulty performing mass upgrade from v6.
If your device came with v7 preinstalled, what is there to worry about? What bugs?
 
ghostt
just joined
Posts: 21
Joined: Tue Apr 24, 2018 4:07 pm
Location: Australia

Re: v7.1.1 is released!

Fri Dec 24, 2021 12:39 am

But remember, when e.g. Microsoft releases a new Windows version...
:)))))))) I even couldn't think of what to say :))))))) But yes, I know exactly what you're talking about. Well, thank you for your thoughts and let's hope that'll happen sooner rather than later.
Last edited by ghostt on Fri Dec 24, 2021 4:47 am, edited 1 time in total.
 
msatter
Forum Guru
Forum Guru
Posts: 2897
Joined: Tue Feb 18, 2014 12:56 am
Location: Netherlands / Nīderlande

Re: v7.1.1 is released!

Fri Dec 24, 2021 12:58 am

New Windows version == more bugs and more vulnerabilities. It's a Microsoft product after all!
 
ghostt
just joined
Posts: 21
Joined: Tue Apr 24, 2018 4:07 pm
Location: Australia

Re: v7.1.1 is released!

Fri Dec 24, 2021 2:47 am

I realise that BGP is not ready yet but maybe it can help to those who is working on it. Test router: CRS125-24G-1S-2HnD, v7.1.1. has a BGP session running to CCR v6.49.2. After a while (usually it happens within an hour) CRS v7 displayed BGP session still up with uptime in the picture (may need to close/reopen Winbox to see that value), CCR v6 displayed the corresponding peer down with state "open sent". As a result, no BGP created dynamic routes existed in the routing table. Rebooting v7 router helped, the test router BGP session went to normal, CCR v6 peer went to "established". But after about 50 minutes, BGP dynamic routes had disappeared again. After closing/reopening Winbox v7 BGP session uptime jumped to similar value shown in the picture. Rebooting helped again.

P.S.
Merry Christmas to everyone and wish you all the best!
You do not have the required permissions to view the files attached to this post.
 
ka4opi4a
newbie
Posts: 30
Joined: Sat Sep 06, 2014 6:36 pm
Location: Bulgaria/EU

Re: v7.1.1 is released!

Fri Dec 24, 2021 1:51 pm

Yesterday updated my home hAP AC from 6.49.2 to 7.1.1. Now I get very low wifi speeds over both wifi networks. Anyone else with the same issue ?
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 26289
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: v7.1.1 is released!

Fri Dec 24, 2021 1:59 pm

Make a separate topic about your wifi woes and include some more info, like screenshots from your router registration table and your computer wifi signal stats.
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Fri Dec 24, 2021 2:20 pm

when the routing/bgp/session prefix count will be fixed?
or maybe you think that it's not so important?
Reading an earlier reply to that, I fear that in some version this value will just disappear.
It is apparently difficult in the current BGP implementation to keep this count in the context of the connection.
Suggestions are made how to retrieve it using a query on the routing table, but of course that only helps for the occasional debugging case, not to keep an overview.

On one of our routers we have 54 BGP peers (in an isolated network, not internet BGP) and we run v6, with a window on BGP peers always open that shows an overview of the peers including prefix count.
A quick glance on that window shows certain problems quickly. That can not easily be replaced by doing queries on the routing table. So when upgrading to v7 we will lose this convenience.
(another issue is that the BGP Peer Cache window does not update when the status changes. so you do not see when connections go offline without refreshing it all the time...)
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Fri Dec 24, 2021 3:41 pm

Hello, colleagues!
On hap ac2 I noticed this bug in ip/routes (WebFig):
That is not really a bug, it is just a cosmetic issue (explainable from the internal workings). The routes still work OK.
 
sunblade87
just joined
Posts: 6
Joined: Thu Sep 24, 2020 2:05 pm

Re: v7.1.1 is released!

Fri Dec 24, 2021 4:17 pm

BGP/Connection/Filter/OutputNetwork not working in Winbox. Instead of address-list names 'unknown' items are shown.
 
gotsprings
Forum Guru
Forum Guru
Posts: 2087
Joined: Mon May 14, 2012 9:30 pm

Re: v7.1.1 is released!

Fri Dec 24, 2021 5:41 pm

Make a separate topic about your wifi woes and include some more info, like screenshots from your router registration table and your computer wifi signal stats.
Why?

I have a separate thread about how Zerotier bridging works different on 7.1 vs 7.1RC4. I don't see any posts in it. Yet you seem to read this one.
 
ka4opi4a
newbie
Posts: 30
Joined: Sat Sep 06, 2014 6:36 pm
Location: Bulgaria/EU

Re: v7.1.1 is released!

Fri Dec 24, 2021 5:51 pm

Yesterday updated my home hAP AC from 6.49.2 to 7.1.1. Now I get very low wifi speeds over both wifi networks. Anyone else with the same issue ?

Try to turn off your hap by the option in system, mine when I turn off in version 7 it turns on again.
Just try this - the device turns off and stay off, doesn't turn back on.
 
SergeS
Frequent Visitor
Frequent Visitor
Posts: 67
Joined: Fri Mar 25, 2016 6:23 am

Re: v7.1.1 is released!

Fri Dec 24, 2021 9:31 pm

Why "Check for Update" does not see v7 automatically?
Is this feature or bug?
Image
 
gotsprings
Forum Guru
Forum Guru
Posts: 2087
Joined: Mon May 14, 2012 9:30 pm

Re: v7.1.1 is released!

Fri Dec 24, 2021 9:33 pm

On a positive note...

I have several WiFi devices that have stayed connected for over 2 days to my Audience, running the new WAVE2 wifi drivers.

I get offline reports from these things several times a day on the regular. So this is an improvement!
 
SergeS
Frequent Visitor
Frequent Visitor
Posts: 67
Joined: Fri Mar 25, 2016 6:23 am

Re: v7.1.1 is released!

Fri Dec 24, 2021 9:33 pm

Why "Check for Update" does not see v7 automatically?
Is this feature or bug?
Ok, found by myself :-), channel needs to be "upgrade".

Is this worthful to upgrade?
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Fri Dec 24, 2021 9:54 pm

When you need to ask these questions, it probably is not yet the time for you to upgrade.
At least read the 116 messages above to see if there is any reported problem that would apply to your usage of the device.
As you can see, 6.49.2 is the "stable" release for your device.
 
SergeS
Frequent Visitor
Frequent Visitor
Posts: 67
Joined: Fri Mar 25, 2016 6:23 am

Re: v7.1.1 is released!

Fri Dec 24, 2021 10:05 pm

When you need to ask these questions, it probably is not yet the time for you to upgrade.
At least read the 116 messages above to see if there is any reported problem that would apply to your usage of the device.
As you can see, 6.49.2 is the "stable" release for your device.
I have read majority of it, in the process, seems like not so many complains...
v7.1.1 is in stable release tree, btw.

p.s. Will wait a little bit more :-(

Image
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Fri Dec 24, 2021 10:24 pm

Yes, for the typical usage of a hAP ac, there will likely not be many issues that you will encounter in 7.1.1
Still, don't come whining here when there are new problems and there isn't any improvement.
 
mducharme
Trainer
Trainer
Posts: 1777
Joined: Tue Jul 19, 2016 6:45 pm
Location: Vancouver, BC, Canada

Re: v7.1.1 is released!

Sat Dec 25, 2021 3:50 am

I have several WiFi devices that have stayed connected for over 2 days to my Audience, running the new WAVE2 wifi drivers.
I get offline reports from these things several times a day on the regular. So this is an improvement!
I have wanted to test wave2 properly at home, but am unable to with the lack of support for 4 address mode (i.e. WDS or station-bridge). I hope MikroTik will be addressing this at some point soon.
 
User avatar
BlackVS
Member Candidate
Member Candidate
Posts: 172
Joined: Mon Feb 04, 2013 7:00 pm
Contact:

Re: v7.1.1 is released!

Sat Dec 25, 2021 11:49 am

Upgraded CCR1009 from 7.1 to 7.1.1 and... got 100% CPU load (usually it was 3..4%). WTF!!! sorry for expression.
You do not have the required permissions to view the files attached to this post.
 
User avatar
BlackVS
Member Candidate
Member Candidate
Posts: 172
Joined: Mon Feb 04, 2013 7:00 pm
Contact:

Re: v7.1.1 is released!

Sat Dec 25, 2021 11:59 am

One more screenshot with 7.1.1 - 2..3Mbit load fully kills 9 core router... it is crazy!!!! Downgrading to 7.1. - CPU load again ~0%. Rhetorical question - do you any firmware tests using different hardware before releasing "stable" versions?
PS: downgrade not helped - within few minutes load again about 70..90%. From Zabbix you can see that before 11:30 (7.1) all was ok, after - 100% loads (on 7.1.1 and 7.1. after downgrade). Pauses - it is reboots
You do not have the required permissions to view the files attached to this post.
 
User avatar
BlackVS
Member Candidate
Member Candidate
Posts: 172
Joined: Mon Feb 04, 2013 7:00 pm
Contact:

Re: v7.1.1 is released!

Sat Dec 25, 2021 12:47 pm

Downgraded to 6.49.2.... "enjoying the silence" %) (CPU is again ~0% load)
You do not have the required permissions to view the files attached to this post.
 
User avatar
Jotne
Forum Guru
Forum Guru
Posts: 3279
Joined: Sat Dec 24, 2016 11:17 am
Location: Magrathean

Re: v7.1.1 is released!

Sat Dec 25, 2021 1:19 pm

You dont have a picture of "Profile" while CPU running high try to see what module cause the problem?
I only see picture while all are ok.
 
User avatar
Halfeez92
Member Candidate
Member Candidate
Posts: 101
Joined: Tue Oct 30, 2012 12:58 pm
Location: 127.0.0.1
Contact:

Re: v7.1.1 is released!

Sat Dec 25, 2021 3:48 pm

Bug on Route List Rules where I cannot drag the rules. Please check!
routelist.png
You do not have the required permissions to view the files attached to this post.
 
User avatar
BlackVS
Member Candidate
Member Candidate
Posts: 172
Joined: Mon Feb 04, 2013 7:00 pm
Contact:

Re: v7.1.1 is released!

Sat Dec 25, 2021 4:08 pm

You dont have a picture of "Profile" while CPU running high try to see what module cause the problem?
I only see picture while all are ok.
If look more carefully %) - on one screenshot above you can see profile open for 7.1.1 (I attached it again here) - networking module causes 100% load. Looks like some "software produced internal network loop". On interfaces tab you can see that in/out traffic is low. Right now I'm on the same config on 6.49.2. - still about zero CPU load... Strange that being on 7.1 before upgrading to 7.1.1 CPU load was low but after upgrading (and afterward downgrade to 7.1) - CPU load is 100%. Looks like upgrade 7.1. to 7.1.1 changed some structure(s) inside firmware which left the same after downgrade to 7.1. Now I'm not intending to upgrade my CCRs (~10 pcs) to 7.x nearest few months until major bugs fixed (I hope they will be fixed, incl.broken mangle chain for CCR1xxx).
You do not have the required permissions to view the files attached to this post.
 
infabo
Long time Member
Long time Member
Posts: 585
Joined: Thu Nov 12, 2020 12:07 pm

Re: v7.1.1 is released!

Sat Dec 25, 2021 6:23 pm

Does anyone know how to debug/log a device lockup? With lockup I mean, that the device is not responding to anything. Not even the "Mode"-button at my chateau - that triggers dark-mode (all led off) is not responding in that device-state.
 
User avatar
harry66
Frequent Visitor
Frequent Visitor
Posts: 53
Joined: Tue Mar 04, 2014 5:29 pm
Location: Germany

Re: v7.1.1 is released!

Sat Dec 25, 2021 6:52 pm

RB3011:
Upgrade from 6.49.2 did not work out:
- Unreliable ping to a switch (CSS326, LACP, VLAN trunk) directly connected (90% packet loss)
- web proxy was disabled during upgrade

Maybe as an effect:
- All Capsman connections lost

What was working:
- PPPoE to provider over VLAN
- Direct connection of laptop via GigE

Unable to determine error source for connectivity problems during longer troubleshooting session
- no hint from log
- no error frames count
- no faulty LACP indication
- no xSTP messages
--> totally clueless, maybe I overlooked something, but 6.49.2-->7.1.1 in my case failed with very basic function

BR
Uwe
 
Sob
Forum Guru
Forum Guru
Posts: 9119
Joined: Mon Apr 20, 2009 9:11 pm

Re: v7.1.1 is released!

Sat Dec 25, 2021 7:24 pm

Bug on Route List Rules where I cannot drag the rules. Please check!
Not a bug, you have sorting on last column, but you need the first one (with #).
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 26289
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: v7.1.1 is released!

Sat Dec 25, 2021 10:53 pm

Make a separate topic about your wifi woes and include some more info, like screenshots from your router registration table and your computer wifi signal stats.
Why?

I have a separate thread about how Zerotier bridging works different on 7.1 vs 7.1RC4. I don't see any posts in it. Yet you seem to read this one.
Sorry about that, I'll stop, to keep the topic clean.
 
User avatar
Halfeez92
Member Candidate
Member Candidate
Posts: 101
Joined: Tue Oct 30, 2012 12:58 pm
Location: 127.0.0.1
Contact:

Re: v7.1.1 is released!

Sun Dec 26, 2021 6:49 am

Bug on Route List Rules where I cannot drag the rules. Please check!
Not a bug, you have sorting on last column, but you need the first one (with #).
Oh my bad, maybe my colleague did some sorting before. I have not noticed. Thank you again sir.
 
User avatar
Jotne
Forum Guru
Forum Guru
Posts: 3279
Joined: Sat Dec 24, 2016 11:17 am
Location: Magrathean

Re: v7.1.1 is released!

Sun Dec 26, 2021 9:32 am

If look more carefully %) - on one screenshot above you can see profile open for 7.1.1
From latest picture, it seems that 7.1.1 uses one CPU compare to the 6.49 that uses 8?
 
User avatar
BlackVS
Member Candidate
Member Candidate
Posts: 172
Joined: Mon Feb 04, 2013 7:00 pm
Contact:

Re: v7.1.1 is released!

Sun Dec 26, 2021 10:12 am

If look more carefully %) - on one screenshot above you can see profile open for 7.1.1
From latest picture, it seems that 7.1.1 uses one CPU compare to the 6.49 that uses 8?
OMG, in resource tab you can see that total load is 89% i.e. not "uses one CPU". I did one screenshot for one CPU due to profile window just allows to choose only one CPU for details. But just little bit above was screenshot with 7.1.1, were show all 9 CPUs, 8 of 9 are 100% load, IRQ is 90..97%.
 
User avatar
Znevna
Forum Guru
Forum Guru
Posts: 1347
Joined: Mon Sep 23, 2019 1:04 pm

Re: v7.1.1 is released!

Sun Dec 26, 2021 10:28 am

So 7.1.1 and 7.2rc1 are versions to stay away from?
Wonder what common change causes this CPU usage on both versions.
Is it triggered by something in the config? does it behave the same after a config reset?
 
User avatar
Jotne
Forum Guru
Forum Guru
Posts: 3279
Joined: Sat Dec 24, 2016 11:17 am
Location: Magrathean

Re: v7.1.1 is released!

Sun Dec 26, 2021 11:45 am

So 7.1.1 and 7.2rc1 are versions to stay away from?
If you read the may comments in the 7.x threads, you see the following comments.

Do your router work fine with 6.x software and you do not need any of the new 7.x functions, stick with 6.x
 
User avatar
Znevna
Forum Guru
Forum Guru
Posts: 1347
Joined: Mon Sep 23, 2019 1:04 pm

Re: v7.1.1 is released!

Sun Dec 26, 2021 11:46 am

How is that in any way relevant to what I've asked above?
: the high CPU usage in these two versions.
 
User avatar
Jotne
Forum Guru
Forum Guru
Posts: 3279
Joined: Sat Dec 24, 2016 11:17 am
Location: Magrathean

Re: v7.1.1 is released!

Sun Dec 26, 2021 12:59 pm

You see what i did reply to in the quote. All v7 are still in early stage. If you do not need it, and all are ok with 6.x, use 6.x
And if 7.x works fine, no problem use it. Its up to you to test to see if it fits your needs.
 
User avatar
Znevna
Forum Guru
Forum Guru
Posts: 1347
Joined: Mon Sep 23, 2019 1:04 pm

Re: v7.1.1 is released!

Sun Dec 26, 2021 1:05 pm

Dude, so far it looks like a bug in 7.1.1 and 7.2rc1, these topics are for problems related to these specific versions, please don't spam the forums with offtopic talk. Wasted 3 posts for nothing.
For general "don't use v7, v7 bad" please open another topic.
Thank you.
So, on topic, did you encounter abnormal high CPU usage on 7.1.1 and 7.2rc1? or not? How did you fix it? did you find what causes it?
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Sun Dec 26, 2021 1:08 pm

The newly added "uptime" field in the BGP connections list does not work correctly. When the connection is down, it keeps counting up from the connection uptime of the previous session. Only when the connection comes back up, it starts counting from zero.
When the connection is not up, that field should be blank or at best showing 00:00:00 all the time.

Another problem with the BGP connections window is that it only updates when you explicitly refresh it (F5 or change of tabs). It should update whenever the status of a connection changes, as in v6.
Last edited by pe1chl on Sun Dec 26, 2021 6:58 pm, edited 1 time in total.
 
ivicask
Member
Member
Posts: 417
Joined: Tue Jul 07, 2015 2:40 pm
Location: Croatia, Zagreb

Re: v7.1.1 is released!

Sun Dec 26, 2021 2:56 pm

Dude, so far it looks like a bug in 7.1.1 and 7.2rc1, these topics are for problems related to these specific versions, please don't spam the forums with offtopic talk. Wasted 3 posts for nothing.
For general "don't use v7, v7 bad" please open another topic.
Thank you.
So, on topic, did you encounter abnormal high CPU usage on 7.1.1 and 7.2rc1? or not? How did you fix it? did you find what causes it?
Not sure what is causing it exactly, some say its larger address lists, i did send supout to support i hope they figure it.
As i wrote, my HAPC2 crashes with out of memory crash after 30mins on 7.2rc1 and CPU hangs around 35%(attached pic) with zero traffic, while on 7.1.1 CPU is ok but still leaks memory and crashes after 1 week.
At work our 4011 was sitting at 500MB! of RAM usage after 3 weeks on v7.1.
You do not have the required permissions to view the files attached to this post.
Last edited by ivicask on Sun Dec 26, 2021 3:35 pm, edited 1 time in total.
 
shavenne
just joined
Posts: 16
Joined: Wed Dec 11, 2019 4:27 pm

Re: v7.1.1 is released!

Sun Dec 26, 2021 6:51 pm

I have two CRS328-24P-4S+ and both are randomly losing links on SFP+ (different modules .. fibre, dac and 10gbase-t. On one of the switches fibre and 10gbase-t always losing its connection at the exact same time) with 7.1.1.

I had to go back to 6.49.2.
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Sun Dec 26, 2021 7:00 pm

My device is RB4011 with wi-fi. Before update i had Ros ver. 6.49.2, After update to Ros 7.1.1 my router became a brick (after 30 minutes uptime ). I see that i have l2tp+ipsec client, but after disable ipsec in l2tp client- my router work fine! I think my case can help users for upgrade to Ros7
I have a RB4011 with WiFi as well, and it is running two L2TP+IPsec clients, but there is no problem. It has another IPsec tunnel as well.
Maybe you need to export the config to a file, reset the config to empty (use winbox in MAC mode for the connection), then import the file again.
I have done that before when I sustpected a config problem and maybe it is the reason I do not have problems now.
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Sun Dec 26, 2021 7:20 pm

Can you write me your IP-IP sec- Proposals and Profiles?
/ip ipsec proposal
set [ find default=yes ] auth-algorithms=sha256,sha1 enc-algorithms=aes-256-cbc,aes-128-cbc

The profile is default
 
User avatar
mjoksimovic
newbie
Posts: 46
Joined: Thu Jun 19, 2008 1:19 pm
Location: Serbia
Contact:

Re: v7.1.1 is released!

Sun Dec 26, 2021 7:30 pm

CCR1009-8G-2S+ (two different devices), CCR1036-8G-2S+EM, RB4011iGS+ and RB1100AHx4, before upgrade to version 7, every of these routers worked perfectly with no freezing. After upgrade, every router freeze after a few hours of work. Kernel error message.
 
infabo
Long time Member
Long time Member
Posts: 585
Joined: Thu Nov 12, 2020 12:07 pm

Re: v7.1.1 is released!

Sun Dec 26, 2021 7:48 pm

Please Mikrotik, please I beg you. Please find a way to generate a supout.rif before a device locks up - so we can send it to support. I have these lockups for months now and it is frustrating (Chateau v7 only)
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Sun Dec 26, 2021 7:50 pm

Not work with your sethings. Can you initiate a trafic thru your l2tp+ipsec tunel? for example rdp connection from your
pc on RB4011 to remote host on vpn? After that your router works fine?
Yes, no problem at all. I use these L2TP tunnels to make connections between private networks (using BGP for autorouting) and it just works. They all are connecting to routers running v6.49 at the moment.
Other tunnels are GRE/IPsec and they work as well. In practice they all use sha256 (sha128 only present to talk to older routers but there are no active connections to those at the moment).

I should say that my RB4011 has *never* crashed during all my experiments with v6 and v7. There is a problem when using v7.2rc1 but it still does not crash, it just doesn't route properly. That is why I use 7.1.1 now.
 
User avatar
osc86
Member Candidate
Member Candidate
Posts: 197
Joined: Wed Aug 09, 2017 1:15 pm

Re: v7.1.1 is released!

Sun Dec 26, 2021 11:50 pm

@infabo
/sys watchdog/set watchdog-timer=yes automatic-supout=yes
look for a file named autosupout.rif in the root directory after the router has locked up / rebooted by watchdog timer.
 
User avatar
nithinkumar2000
Member Candidate
Member Candidate
Posts: 157
Joined: Wed Sep 11, 2019 7:42 am
Location: Coimbatore
Contact:

Re: v7.1.1 is released!

Mon Dec 27, 2021 5:40 am

Getting Kernal Failure....
Capture.JPG
You do not have the required permissions to view the files attached to this post.
 
mducharme
Trainer
Trainer
Posts: 1777
Joined: Tue Jul 19, 2016 6:45 pm
Location: Vancouver, BC, Canada

Re: v7.1.1 is released!

Mon Dec 27, 2021 6:36 am

I am encountering higher CPU load than normal on mipsbe devices such as the hAP ac lite and hAP ac. Even with just a few Mbps of download the CPU goes up to 25% on the hAP ac which is a lot higher than I would expect. When they hit too high CPU usage, the wireless malfunctions and drops - it doesn't even take 100% usage, it seems to drop even at around 50% (these are single core devices). Wifi connectivity is stable as long as traffic levels are minimal. In my case I am just using the hAP ac lite as a bridge, not a router, so this should have nothing to do with route caching.

EDIT: I tried setting an AP tx limit and client tx limit on the RB4011 AP for the client hap ac lite wireless bridge client. Even a small limit (5Mbps) still disconnected when running a speed test on speedtest.net.
Last edited by mducharme on Mon Dec 27, 2021 7:07 am, edited 1 time in total.
 
manuek
just joined
Posts: 1
Joined: Sun Jan 03, 2021 7:51 am

Re: v7.1.1 is released!

Mon Dec 27, 2021 7:05 am

Hello people, I have a question, how do I place the traffic inside a TE tunnel? because it does not work the same as in RouterOS v6
 
No13TGP
just joined
Posts: 5
Joined: Tue Apr 08, 2014 10:10 am

Re: v7.1.1 is released!

Mon Dec 27, 2021 8:23 am

Upgrade 7.1.1 vers. wAP Ac (architecture mipsbe). There are still problems with Upload speed. This is critically low. There was no such problem with version 6.49.2!
Same here, after the upgrade 5ghz wifi will not work properly.

Running on the default config all seems to be ok (low volume; no issues)
But when transfer speeds reach > 100mbit the throughput drops to 0 and stays there for several seconds.
Every 10 seconds or so it tries to restart the transfer and fails almost immediately.
 
mducharme
Trainer
Trainer
Posts: 1777
Joined: Tue Jul 19, 2016 6:45 pm
Location: Vancouver, BC, Canada

Re: v7.1.1 is released!

Mon Dec 27, 2021 8:26 am

But when transfer speeds reach > 100mbit the throughput drops to 0 and stays there for several seconds.
Every 10 seconds or so it tries to restart the transfer and fails almost immediately.
Yes this is the issue I reported two posts above with the hAP ac (mipsbe) and hAP ac lite (mipsbe). It is not only that the throughput drops to zero, the client actually gets disconnected, if you look in the registration table.
 
Vooray
Frequent Visitor
Frequent Visitor
Posts: 73
Joined: Mon Feb 23, 2015 3:34 pm

Re: v7.1.1 is released!

Mon Dec 27, 2021 11:18 am

strange routing issue
> /system/package/print 
Columns: NAME, VERSION
# NAME      VERSION
0 routeros  7.1.1  
first of all i can add multiple same routes in RIB. That is strange:
> /ip route/print where 7.7.7.7/32 in dst-address 
Flags: D - dynamic; X - disabled, I - inactive, A - active; c - connect, s - static, r - rip, b - bgp, o - ospf, d - dhcp, v - vpn, m - modem, y - copy; H - hw-offloaded; + - ecmp 
 #       DST-ADDRESS        GATEWAY            DISTANCE
   ...cut...
 3  As + 7.7.7.7/32         IFACE-WARP                1
 4  As + 7.7.7.7/32         IFACE-WARP                1
 5  As + 7.7.7.7/32         IFACE-WARP                1
 1  As + 7.7.7.7/32         IFACE-WARP                1
next i can not delete all of them:
 /ip/route> remove [find dst-address =7.7.7.7/32]
no such item (4)
 /ip/route> /ip route/print where 7.7.7.7/32 in dst-address 
Flags: D - dynamic; X - disabled, I - inactive, A - active; c - connect, s - static, r - rip, b - bgp, o - ospf, d - dhcp, v - vpn, m - modem, y - copy; H - hw-offloaded; + - ecmp 
 #       DST-ADDRESS        GATEWAY            DISTANCE
 4  As + 7.7.7.7/32         IFACE-WARP                1
 1  As + 7.7.7.7/32         IFACE-WARP                1
 /ip/route> remove numbers=4,1
no such item (4)
 
infabo
Long time Member
Long time Member
Posts: 585
Joined: Thu Nov 12, 2020 12:07 pm

Re: v7.1.1 is released!

Mon Dec 27, 2021 12:05 pm

@infabo
/sys watchdog/set watchdog-timer=yes automatic-supout=yes
look for a file named autosupout.rif in the root directory after the router has locked up / rebooted by watchdog timer.
This config I have already in place. I guess it is default-config already.
Autosupout seems only to work for kernel panic, where the watchdog can reboot the device after capturing the autosupout file. Had kernel panics in the past and the autosupout.rif I could hand over to support. But now the device gets totally unavailable and no file is created.
 
User avatar
mjoksimovic
newbie
Posts: 46
Joined: Thu Jun 19, 2008 1:19 pm
Location: Serbia
Contact:

Re: v7.1.1 is released!

Mon Dec 27, 2021 12:08 pm

Getting Kernal Failure....

Capture.JPG

The same problem.

Image
You do not have the required permissions to view the files attached to this post.
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Mon Dec 27, 2021 12:30 pm

You can generate supout.rif immediately after this happens and send it to support. I think there is more info in the supout.rif than in the error log.
 
User avatar
fcucci
newbie
Posts: 36
Joined: Mon Feb 13, 2012 11:31 am
Location: Italy

Re: v7.1.1 is released!

Mon Dec 27, 2021 1:23 pm

Hello,
I have installed routeros 7.1.1 on a CCR1009-7G-1C-1S+ (tile) but I don't see packages listed; on terminal too:
Immagine 2021-12-27 122604.jpg
You do not have the required permissions to view the files attached to this post.
 
User avatar
mkx
Forum Guru
Forum Guru
Posts: 11381
Joined: Thu Mar 03, 2016 10:23 pm

Re: v7.1.1 is released!

Mon Dec 27, 2021 1:31 pm

Hello,
I have installed routeros 7.1.1 on a CCR1009-7G-1C-1S+ (tile) but I don't see packages listed; on terminal too:
Immagine 2021-12-27 122604.jpg

In ROSv7 only a few non-essential things come as packages, everything else is in a single monolithic intallation package.
 
accarda
Member Candidate
Member Candidate
Posts: 208
Joined: Fri Apr 05, 2019 4:06 pm
Location: Italy

Re: v7.1.1 is released!

Mon Dec 27, 2021 2:16 pm

I have tried to implement a recursive route (like in ros v6), but I don't see it working, unless the syntax has completely changed.
The route gets IUSH as invalid and unreachable.
Is this not implemented yet in ros v7.1.1 ?
 
akarpas
Member Candidate
Member Candidate
Posts: 177
Joined: Tue Mar 20, 2018 4:46 pm

Re: v7.1.1 is released!

Mon Dec 27, 2021 2:18 pm

updated my ccr 1009 now its bricked not booting not loading kernel
 
User avatar
rushlife
Member Candidate
Member Candidate
Posts: 243
Joined: Thu Nov 05, 2015 12:30 pm

Re: v7.1.1 is released!

Mon Dec 27, 2021 3:17 pm

updated my
ccr1036
2x ccr1009
2x ccr1016
rb5009
rb4011 and couple of different models too and....

no problemo
 
ormandj
just joined
Posts: 18
Joined: Tue Jun 15, 2021 12:25 am

Re: v7.1.1 is released!

Mon Dec 27, 2021 3:41 pm

I have two CRS328-24P-4S+ and both are randomly losing links on SFP+ (different modules .. fibre, dac and 10gbase-t. On one of the switches fibre and 10gbase-t always losing its connection at the exact same time) with 7.1.1.

I had to go back to 6.49.2.
I have the same problems. SUP-68278 is there if you want to submit a report and reference it. Setting the modules to 1G fixes it, but I hope Mikrotik will fix this soon, as it's a serious problem impacting a lot of users. 7.1 and 7.1.1 both cause it for me, primarily at 5 minute intervals.
 
akarpas
Member Candidate
Member Candidate
Posts: 177
Joined: Tue Mar 20, 2018 4:46 pm

Re: v7.1.1 is released!

Mon Dec 27, 2021 4:59 pm

updated my ccr 1009 now its bricked not booting not loading kernel
Had to reisntall using Netinstall sad had to do it but was a great experience how to recover device from such a problem.
 
User avatar
mjoksimovic
newbie
Posts: 46
Joined: Thu Jun 19, 2008 1:19 pm
Location: Serbia
Contact:

Re: v7.1.1 is released!

Mon Dec 27, 2021 5:47 pm

updated my
ccr1036
2x ccr1009
2x ccr1016
rb5009
rb4011 and couple of different models too and....

no problemo
Let us know the status after few hours or days. ;-)
 
User avatar
fcucci
newbie
Posts: 36
Joined: Mon Feb 13, 2012 11:31 am
Location: Italy

Re: v7.1.1 is released!

Mon Dec 27, 2021 6:00 pm

Hello,
I have installed routeros 7.1.1 on a CCR1009-7G-1C-1S+ (tile) but I don't see packages listed; on terminal too:
Immagine 2021-12-27 122604.jpg

In ROSv7 only a few non-essential things come as packages, everything else is in a single monolithic intallation package.
OK and how can I uninstall wireless package ?
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Mon Dec 27, 2021 6:38 pm

OK and how can I uninstall wireless package ?
You cannot. This is no longer possible in v7 (same for MPLS, Hotspot, CapsMan etc).
 
mducharme
Trainer
Trainer
Posts: 1777
Joined: Tue Jul 19, 2016 6:45 pm
Location: Vancouver, BC, Canada

Re: v7.1.1 is released!

Mon Dec 27, 2021 6:52 pm

I have tried to implement a recursive route (like in ros v6), but I don't see it working, unless the syntax has completely changed.
This has been covered many many times. target-scope now has to be greater than scope instead of being greater than or equal to scope. Increase your target-scope by 1 and it should work.
 
accarda
Member Candidate
Member Candidate
Posts: 208
Joined: Fri Apr 05, 2019 4:06 pm
Location: Italy

Re: v7.1.1 is released!

Mon Dec 27, 2021 7:01 pm

This has been covered many many times. target-scope now has to be greater than scope instead of being greater than or equal to scope. Increase your target-scope by 1 and it should work.
Thanks for the heads up, I was missing this info.
 
akarpas
Member Candidate
Member Candidate
Posts: 177
Joined: Tue Mar 20, 2018 4:46 pm

Re: v7.1.1 is released!

Mon Dec 27, 2021 7:52 pm

not sure why but after update as I have said my ccr 1009 didnt boot anymore had to use netinstall to reimage and now its not recognising mikrosd car tried 2 of them no luck
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Mon Dec 27, 2021 8:08 pm

not sure why but after update as I have said my ccr 1009 didnt boot anymore had to use netinstall to reimage and now its not recognising mikrosd car tried 2 of them no luck
You could have read both of these things above. It really pays off to read the release topic before attempting to upgrade!
 
AlexPC
just joined
Posts: 1
Joined: Tue Mar 10, 2020 2:03 pm

Re: v7.1.1 is released!

Mon Dec 27, 2021 8:13 pm

Did netinstall, it also does not help to reset all settings, 1 wireless interface does not appear. ( 7.1.1 Stable | 7.2rc1 Testing)
DefConf gen: Unable to find wifiwave2 interface(s)
error while running customized default configuration script: interrupted
 
mducharme
Trainer
Trainer
Posts: 1777
Joined: Tue Jul 19, 2016 6:45 pm
Location: Vancouver, BC, Canada

Re: v7.1.1 is released!

Mon Dec 27, 2021 8:15 pm

Did netinstall, it also does not help to reset all settings, 1 wireless interface does not appear. ( 7.1.1 Stable | 7.2rc1 Testing)
It gives a warning in the manual that on the RB4011 using wifiwave2 will result in not having a 2.4ghz interface. Remove wifiwave2 and the interface will appear again.

Also, the default configuration script doesn't have the right syntax for wifiwave2, so if you netinstall with wifiwave2 or if you reset to defaults with wifiwave2 installed then it will fail to load. If you want to use wifiwave2, you should netinstall without it or reset to defaults without it, and then install wifiwave2 after.
 
akarpas
Member Candidate
Member Candidate
Posts: 177
Joined: Tue Mar 20, 2018 4:46 pm

Re: v7.1.1 is released!

Mon Dec 27, 2021 8:25 pm

not sure why but after update as I have said my ccr 1009 didnt boot anymore had to use netinstall to reimage and now its not recognising mikrosd car tried 2 of them no luck
You could have read both of these things above. It really pays off to read the release topic before attempting to upgrade!
what release its considered to be stable version free of bugs isnt?
 
akarpas
Member Candidate
Member Candidate
Posts: 177
Joined: Tue Mar 20, 2018 4:46 pm

Re: v7.1.1 is released!

Mon Dec 27, 2021 8:27 pm

Looks like SD cards still do not mount on CCR1009-7G-1C-1S+, same on 7.2rc1.
for me the same on 7.1.1
 
mducharme
Trainer
Trainer
Posts: 1777
Joined: Tue Jul 19, 2016 6:45 pm
Location: Vancouver, BC, Canada

Re: v7.1.1 is released!

Tue Dec 28, 2021 12:42 am

what release its considered to be stable version free of bugs isnt?
"Free of bugs"? No, that's not what MikroTik's definition of "stable" means. You won't find any vendor where a "stable" release is 100% free of bugs, it just doesn't happen. "Stable" in MikroTik's case means that they felt that it worked well enough for about 90% of users and use cases.

Do you also upgrade to Windows 11 a week or two after it came out and complain about bugs and say it must also be bug free? RouterOS v7 is a complete rewrite of probably about half the code. It isn't some little upgrade. They will be ironing out bugs for months.
 
akarpas
Member Candidate
Member Candidate
Posts: 177
Joined: Tue Mar 20, 2018 4:46 pm

Re: v7.1.1 is released!

Tue Dec 28, 2021 1:57 am

what release its considered to be stable version free of bugs isnt?
"Free of bugs"? No, that's not what MikroTik's definition of "stable" means. You won't find any vendor where a "stable" release is 100% free of bugs, it just doesn't happen. "Stable" in MikroTik's case means that they felt that it worked well enough for about 90% of users and use cases.

Do you also upgrade to Windows 11 a week or two after it came out and complain about bugs and say it must also be bug free? RouterOS v7 is a complete rewrite of probably about half the code. It isn't some little upgrade. They will be ironing out bugs for months.
it might have a minor bugs , minor is acceptable but not then device gets in to bricked mode were you have to re-image it. Other thing device shouldn't have a a problem like not seeing microSD card while device has only funny 128mb of storage ( we can start argue why I should need more storage, bur its plenty of reasons for this). So bugs like these are critical and should not happen in stable release.
Other wise i have to say in 4 years experience with Mikrotik this is first time I have such a disappointment with a hope it will be fixed.
Next is regarding windows 11: I participated in dev stage in pre-release stage and in final stage, I have 3 of my personal and a lot of business PC.s upgraded to win 11 and starting from dev stage I had no such a critical bugs. So.......
 
mducharme
Trainer
Trainer
Posts: 1777
Joined: Tue Jul 19, 2016 6:45 pm
Location: Vancouver, BC, Canada

Re: v7.1.1 is released!

Tue Dec 28, 2021 2:05 am

it might have a minor bugs , minor is acceptable but not then device gets in to bricked mode were you have to re-image it.
What version was it on before you upgraded?

Re: Win11 I am on Windows 11 and am experiencing some extremely annoying bugs, mostly to do with 4K scaling and the start menu stops working until I restart explorer. Also it happened last week where all the menu bars started opening *behind* the windows instead of in front of them so I couldn't see the menu options for anything and had to reboot to fix it. So I haven't been impressed by it so far.
 
akarpas
Member Candidate
Member Candidate
Posts: 177
Joined: Tue Mar 20, 2018 4:46 pm

Re: v7.1.1 is released!

Tue Dec 28, 2021 2:17 am

it might have a minor bugs , minor is acceptable but not then device gets in to bricked mode were you have to re-image it.
What version was it on before you upgraded?

Re: Win11 I am on Windows 11 and am experiencing some extremely annoying bugs, mostly to do with 4K scaling and the start menu stops working until I restart explorer. Also it happened last week where all the menu bars started opening *behind* the windows instead of in front of them so I couldn't see the menu options for anything and had to reboot to fix it. So I haven't been impressed by it so far.
question do you have upgrade or clean install ? is you hardware fully supported?
It was version 7.1 :) just so simple
 
mducharme
Trainer
Trainer
Posts: 1777
Joined: Tue Jul 19, 2016 6:45 pm
Location: Vancouver, BC, Canada

Re: v7.1.1 is released!

Tue Dec 28, 2021 2:41 am

question do you have upgrade or clean install ? is you hardware fully supported?
Yes, it is fully supported, and I did an upgrade.

7.1 to 7.1.1 I would not expect to give major issues like that. I do not have a tilera based system to test on, but everything I have upgraded has gone fine from 7.1 to 7.1.1.
 
akarpas
Member Candidate
Member Candidate
Posts: 177
Joined: Tue Mar 20, 2018 4:46 pm

Re: v7.1.1 is released!

Tue Dec 28, 2021 2:52 am

question do you have upgrade or clean install ? is you hardware fully supported?
Yes, it is fully supported, and I did an upgrade.

7.1 to 7.1.1 I would not expect to give major issues like that. I do not have a tilera based system to test on, but everything I have upgraded has gone fine from 7.1 to 7.1.1.
I have re-imaged to 7.1.1 from this point it worked ok, but as i got a problem with SD card I have downgraded to 7.1 and still had the same sd card issue, so nothing stopped me to update back to 7.1.1 and this time all went ok no problems , exempt not working SD card and dccp, sctp and udp lite firewall service ports showing as invalid apart of this all works fine. I saw somebody else has reported the same issue with service ports on the same device after upgrade to 7.1
 
mducharme
Trainer
Trainer
Posts: 1777
Joined: Tue Jul 19, 2016 6:45 pm
Location: Vancouver, BC, Canada

Re: v7.1.1 is released!

Tue Dec 28, 2021 3:01 am

dccp, sctp and udp lite firewall service ports showing as invalid
These service ports have shown as invalid since the first v7 beta on all devices. I think that these helpers have been removed from the newer Linux kernels as they aren't used anymore, but MikroTik hasn't removed the helpers from the list yet. It probably isn't very high up on their list of priorities since it doesn't cause any actual issues.
 
truefriendcz
newbie
Posts: 39
Joined: Mon Jun 05, 2017 11:07 am

Re: v7.1.1 is released!

Tue Dec 28, 2021 11:38 am

BUG:
After connecting to the Shrew Soft VPN Client service, the connection to any server connection is dead after about five minutes (for all connections from LAN and router). The entire router stops transmitting data. Loss of Internet connectivity. The routing table, dns, etc. are fine, but the internet connectivity from the router and from the entire LAN simply does not work.
Tested on the router after reset with default configuration.
Tested on RouterOS v7.1.1 stable.
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Tue Dec 28, 2021 11:50 am

This kind of report is not very useful without information like "what kind of VPN is this" (preferably show the export of the configuration with account info masked), and what type of router you use. Some recent VPN issues really depend on the architecture of the router (TILE, ARM, MIPS etc).
 
rpingar
Long time Member
Long time Member
Posts: 592
Joined: Fri May 28, 2004 2:46 pm
Location: Italy

Re: v7.1.1 is released!

Tue Dec 28, 2021 1:35 pm

we have restricted the issue about icmp that stop working after several hours of operation on x86.
It is related to bonding MTU >1500.
To reproduce, on a v.7.1.1 router configure two bond interface, one with mtu=1500 and the second with mtu=1600
Do an heavy and costant forward of traffic through the bond interfaces and after 36/48 hours the router:
- is not able to ping ecternal hosts
- is not able to ping-check the static routes
- respond correctly to ping from external hosts

Using the same hardware, same config changing only mtu=1500 on all bonding interfaces the router remains stable!

We think it is not a platform (x86) related issue, but a general issue.
regards
Ros
 
Note
Frequent Visitor
Frequent Visitor
Posts: 78
Joined: Fri Jun 03, 2016 12:39 pm

Re: v7.1.1 is released!

Tue Dec 28, 2021 1:46 pm

upgrading to 7 broke my 2 wan failover routing.
This was my route at 6 that was working just fine
/ip route
add distance=1 gateway=1.0.0.1 routing-mark=to_WAN2
add distance=1 gateway=1.1.1.1 routing-mark=to_WAN1
add check-gateway=ping distance=1 gateway=1.1.1.1
add check-gateway=ping distance=2 gateway=1.0.0.1


add check-gateway=ping distance=1 dst-address=1.0.0.1/32 gateway=192.168.2.1 scope=10
add check-gateway=ping distance=1 dst-address=1.1.1.1/32 gateway=192.168.0.1 scope=10
The 4 first lines r the same that they appear in winbox as red.

Any idea of what to do now?
 
truefriendcz
newbie
Posts: 39
Joined: Mon Jun 05, 2017 11:07 am

Re: v7.1.1 is released!

Tue Dec 28, 2021 1:56 pm

This kind of report is not very useful without information like "what kind of VPN is this" (preferably show the export of the configuration with account info masked), and what type of router you use. Some recent VPN issues really depend on the architecture of the router (TILE, ARM, MIPS etc).
"what kind of VPN is this":
https://www.shrew.net/download/vpn/vpn- ... elease.exe
This is simple VPN client (i am installed as Standard edition selected in install wizard)... and use this profile in attachment (Profile.zip) (import only after install and can use).
Profile.zip
Tested on ARM tree devices:
1. MikroTik hAP ac2
2. MikroTik hAP ac3
3. MikroTik hAP ac3 LTE6 kit

RouterOS 7.1.1 (Stable) in default configurations (after reset config)
You do not have the required permissions to view the files attached to this post.
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Tue Dec 28, 2021 2:49 pm

What is not clear to me: is this a program you run on a separate PC, or did you create an IPsec VPN on your router to connect to this service?
When you run it on a PC, the router is performing NAT only and it could be the settings for connection tracking are incorrect or that this function is broken in the current RouterOS.
It could also be a problem in DSCP handling. I experience this myself on the ARM platform but that particular problem was also present in v6.
I think to reproduce that, you have to have internet connection over PPPoE on top of a VLAN (discussed above as problematic by other users as well).
In my situation that problem is not reproducible on the MIPSBE platform (RB2011).
 
accarda
Member Candidate
Member Candidate
Posts: 208
Joined: Fri Apr 05, 2019 4:06 pm
Location: Italy

Re: v7.1.1 is released!

Tue Dec 28, 2021 2:50 pm

I have migrated some more device to Ros v7.1.1 and I have noticed this issue with RoMON compatibility; I still have some device on Ros v6.48.6 though.
All devices have a management VLAN being defined.
All devices that are still on Ros v6 are seen on RoMON neighbors list.
Devices on Ros v7.1.1 are NOT seen if I enable VLAN directly on switch chip (this is done to avoid loosing hardware offload at the bridge level).
Devices on Ros v7.1.1 which are not using VLAN setup (neither bridge or switch setup), but have a VLAN interface being defined are seen properly.
Devices on Ros v7.1.1 which are using VLAN setup on bridge (CRS3xx switch) are seen on RoMON.
 
infabo
Long time Member
Long time Member
Posts: 585
Joined: Thu Nov 12, 2020 12:07 pm

Re: v7.1.1 is released!

Tue Dec 28, 2021 6:45 pm

You miss the "zone" parameter?
 
mducharme
Trainer
Trainer
Posts: 1777
Joined: Tue Jul 19, 2016 6:45 pm
Location: Vancouver, BC, Canada

Re: v7.1.1 is released!

Tue Dec 28, 2021 10:36 pm

I am having the same issue with station-bridge on a hap ac lite connecting to an RB4011, where it will lose connection when doing a speedtest. It only stays reliably connected with very light traffic. I am not using wifiwave2, so station-bridge works. The issue is obviously on the hap ac lite side.
 
infabo
Long time Member
Long time Member
Posts: 585
Joined: Thu Nov 12, 2020 12:07 pm

Re: v7.1.1 is released!

Tue Dec 28, 2021 11:55 pm

 
toxicfusion
Member Candidate
Member Candidate
Posts: 267
Joined: Mon Jan 14, 2013 6:02 pm

Re: v7.1.1 is released!

Wed Dec 29, 2021 5:20 am

Hello,
I have some problem from last update.
mikrotik.png
The Hap ac lite is connected to RB4011 by 5GHz interfaces where RB4011 is ap(wifi wave2) and hap ac lite is a station.
When I add the EOIP to bridge, where I have also lan1-5 and 2.4GHz (the eoip is between RB4011 and hap ac lite).
My wifi on hap ac lite is not stable for example doing speedtest the connection is getting lost.
I got error like this:74:4D:28:D9:DC:98@5ghz: lost connection, received deauth: class 2 frame received (6)
The rest of devices connected to RB4011 by Wifi works great.
And now the most funny thing. Deleting the eoip, creating simple masquerade and seting ip and dhcp sever on bridge is helpful, cause the problem is solved. The connection is stable and fast.
But I want to bridge station and bridge, the station bridge doesn't work for 802.11 and the station-pseudobridge doesn't work like I would like to.
This is a really strange situation and I do not see any relation.
Could someone help me?
The hap ac lite replaces me 2.4GHz in rb4011 where the 2.4ghz(in this model) is not supported for wifi wave2.
Sorry For My English.
I am experiencing the same issue! I upgraded hAP ac3 to latest 7.1.1 from 7.1 - all was OK

However, soon as I upgraded wAP AC (mipsbe) to 7.1.1 or even 7.1.2rc - unstable and disconnects after a few mins. Same setup for AP station and bridge-station.

Reverted the wAP AC back to routerOS 6 - long term and no issues. Back to being stable
 
mducharme
Trainer
Trainer
Posts: 1777
Joined: Tue Jul 19, 2016 6:45 pm
Location: Vancouver, BC, Canada

Re: v7.1.1 is released!

Wed Dec 29, 2021 6:57 am

I am experiencing the same issue! I upgraded hAP ac3 to latest 7.1.1 from 7.1 - all was OK

However, soon as I upgraded wAP AC (mipsbe) to 7.1.1 or even 7.1.2rc - unstable and disconnects after a few mins. Same setup for AP station and bridge-station.

Reverted the wAP AC back to routerOS 6 - long term and no issues. Back to being stable
Yes, this issue seems to happen with at least hAP ac (mipsbe), wAP ac (mipsbe), hAP ac lite (mipsbe)
 
rpingar
Long time Member
Long time Member
Posts: 592
Joined: Fri May 28, 2004 2:46 pm
Location: Italy

Re: v7.1.1 is released!

Wed Dec 29, 2021 3:47 pm

we have restricted the issue about icmp that stop working after several hours of operation on x86.
It is related to bonding MTU >1500.
To reproduce, on a v.7.1.1 router configure two bond interface, one with mtu=1500 and the second with mtu=1600
Do an heavy and costant forward of traffic through the bond interfaces and after 36/48 hours the router:
- is not able to ping ecternal hosts
- is not able to ping-check the static routes
- respond correctly to ping from external hosts

Using the same hardware, same config changing only mtu=1500 on all bonding interfaces the router remains stable!

We think it is not a platform (x86) related issue, but a general issue.
regards
Ros

@Normis we got this sstrange behavior also on CHR!!!!!!!
please analize the last supout attached to #[SUP-67882]

thanks
Ros
 
User avatar
amb3r
just joined
Posts: 16
Joined: Fri Oct 31, 2014 8:35 am

Re: v7.1.1 is released!

Wed Dec 29, 2021 4:27 pm

I have problem with Web Proxy Access Action when set to Deny will revert back to Allow after reopening winbox.
Anyone experiencing it or is there any new configuration to make it stick to Deny? I'm using v7.1.1.1 in RB2011
 
Guscht
Member Candidate
Member Candidate
Posts: 236
Joined: Thu Jul 01, 2010 5:32 pm

Re: v7.1.1 is released!

Wed Dec 29, 2021 7:27 pm

Please explain what:
backup - added "force-v6-to-v7-configuration-upgrade" option on backup load to clear RouterOS v7 configuration and trigger reimport of RouterOS v6 route configuration (CLI only);
means?

You write v6-to-v7 and in the explanation you write something v7 to v6... unclear when to use and what are the benefits?
 
infabo
Long time Member
Long time Member
Posts: 585
Joined: Thu Nov 12, 2020 12:07 pm

Re: v7.1.1 is released!

Wed Dec 29, 2021 8:01 pm

Infabo, can you explain to me how to use it in the script i am using?
Sry, i am Not your DNS Administrator. So i cant give you More than the Info, that the Error you See is probably because of the Missing Zone param.
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Wed Dec 29, 2021 9:42 pm

Why don't you read the help page that is in the reply? There is an example in there:
dns-update dns-server=23.34.45.56 name=mydomain zone=myzone.com address=68.42.14.4 key-name=dns-update-key key=update
Of course you need to substitute your correct values for your zone.
 
infabo
Long time Member
Long time Member
Posts: 585
Joined: Thu Nov 12, 2020 12:07 pm

Re: v7.1.1 is released!

Wed Dec 29, 2021 11:37 pm

It may be a bug as well, when it worked in v6. you say it is changeip.com - i assume there is no need to specify the zone param.
 
blurrybird
newbie
Posts: 38
Joined: Sun Jan 19, 2020 12:25 pm

Re: v7.1.1 is released!

Thu Dec 30, 2021 5:27 am

As mentioned in my other thread viewtopic.php?p=901271 and associated SUP-70209 ticket, IPv6 does not seem to be working with any Simple Queues on my WAN interface at the moment.
 
poirus
just joined
Posts: 1
Joined: Thu Dec 09, 2021 8:31 am

Re: v7.1.1 is released!

Thu Dec 30, 2021 11:02 am

CCR 1009 enable OVPN client or server over UDP -router was rebooted without proper shutdown, probably kernel failure and kernel failure in previous boot
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Thu Dec 30, 2021 12:03 pm

In this case you should download the v7.1.1 .npk file from the website, upload it to the router, and reboot the router from the system->reboot menu.
But I would advise to first partition the router with 2 partitions and copy part0 to part1 (when that works in that particular version).
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 26289
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: v7.1.1 is released!

Thu Dec 30, 2021 12:08 pm

7.0.5 could need the Testing channel to get to 7.1.1, it still has old channels inside
 
rpingar
Long time Member
Long time Member
Posts: 592
Joined: Fri May 28, 2004 2:46 pm
Location: Italy

Re: v7.1.1 is released!

Thu Dec 30, 2021 1:00 pm

Normis, may you support us to fix the issue about ticket [SUP-67221] present on x86 and CHR?
it is about router not able to ping-check the static route after some hours of operation.

It is very urgent because it is compromising the stability of our network.
regards
 
User avatar
Maggiore81
Trainer
Trainer
Posts: 558
Joined: Sun Apr 15, 2012 12:10 pm
Location: Italy
Contact:

Re: v7.1.1 is released!

Thu Dec 30, 2021 4:56 pm

I upgraded a HAP AC2 from latest longterm
the CPU is now running at 448MHz and in the system routerboard page, is set to AUTO.

is that normal?
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Thu Dec 30, 2021 5:05 pm

Yes that is normal. The CPU speed switches automatically according to system load.
 
User avatar
Znevna
Forum Guru
Forum Guru
Posts: 1347
Joined: Mon Sep 23, 2019 1:04 pm

Re: v7.1.1 is released!

Thu Dec 30, 2021 5:07 pm

And under load it overclocks, sadly.
 
User avatar
Maggiore81
Trainer
Trainer
Posts: 558
Joined: Sun Apr 15, 2012 12:10 pm
Location: Italy
Contact:

Re: v7.1.1 is released!

Thu Dec 30, 2021 5:16 pm

And under load it overclocks, sadly.
So MT didn't know that?
I have set it to 716MHz as it was in ROS 6.x
 
User avatar
Znevna
Forum Guru
Forum Guru
Posts: 1347
Joined: Mon Sep 23, 2019 1:04 pm

Re: v7.1.1 is released!

Thu Dec 30, 2021 5:22 pm

I've mentioned it a few times in release topics, they never said anything about the overclocking part.
 
infabo
Long time Member
Long time Member
Posts: 585
Joined: Thu Nov 12, 2020 12:07 pm

Re: v7.1.1 is released!

Thu Dec 30, 2021 6:23 pm

And under load it overclocks, sadly.
This is apparently true. I reported some instability of Chateau to MT support and they suggested to set a fixed CPU frequency. That indeed improved the stability a lot. Still some unknown conditions cause a lockup. But not using CPU auto frequency helped a lot.
 
ahmedalmosowe
just joined
Posts: 4
Joined: Thu Mar 03, 2016 8:06 pm

Re: v7.1.1 is released!

Fri Dec 31, 2021 9:48 am

Routeros 7.1 stable error 404 login page hotspot
but v 6 work fine
 
buraglio
Frequent Visitor
Frequent Visitor
Posts: 70
Joined: Mon Aug 10, 2015 5:59 pm
Location: +1 (217)
Contact:

Re: v7.1.1 is released!

Fri Dec 31, 2021 7:48 pm

Am I missing something or is there a pretty significant piece of BGP missing in ROS7? In ROS 6.x the ability to view advertised routes was pretty straightforward:
[buraglio@gw] /routing bgp> /routing bgp advertisements print
PEER     PREFIX               NEXTHOP          AS-PATH                                                                                                         ORIGIN     LOCAL-PREF
peer1.   3ffe:9440::/32       2001:db8:c00...                                                                                                                 igp
This appears to be gone in 7.x and I have yet been able to find out the analog. What am I missing?

Thanks!
nb
 
oe5nip
just joined
Posts: 5
Joined: Fri Dec 27, 2019 9:00 pm
Location: Kronstorf

Re: v7.1.1 is released!

Fri Dec 31, 2021 8:44 pm

On my router all ok, but not possible to deactivate some Moduls for example dns Server etc
 
obscurus
newbie
Posts: 29
Joined: Thu May 04, 2017 9:25 am

Re: v7.1.1 is released!

Sat Jan 01, 2022 2:27 pm

After upgrade to 7.1.1 from v6 i have an issue with l2tp+ipsec with error

<ip>: authentication failed: peer didn't respond to CHAP challenge
 
espacioint
just joined
Posts: 8
Joined: Thu Mar 16, 2017 11:12 pm
Location: Mijas
Contact:

Re: v7.1.1 is released!

Sat Jan 01, 2022 3:25 pm

Is mikrotik going to do something with wireless?
with ros7 they says that some thing will improve... we have not still ac spectral history, no nv2 support, and more.
Im really dissapointed with mikrotik, I use to buy more than 2000 by month of mikrotik equipment... now only 100 by month and even less day by day, this are the consecuencies of lies and fallen promises
 
romihg
Frequent Visitor
Frequent Visitor
Posts: 50
Joined: Tue Jun 24, 2014 9:07 am
Location: SLOVENIA

Re: v7.1.1 is released!

Sat Jan 01, 2022 10:47 pm

Hello
Can not upgrade RBSXTsqG-5acD from 6.49.2 to 7.1.1 via System>Package >upgrade. I have only esential package on device.
[admin@MikroTik AP] /system package> print
Flags: X - disabled
# NAME VERSION SCHEDULED
0 system 6.49.2
1 dhcp 6.49.2
2 wireless 6.49.2
3 security 6.49.2

And still is after rebut
dec/25/2021 17:12:15 system,info installed routeros-7.1.1-arm
dec/25/2021 17:12:15 system,error not enough space for upgrade
dec/25/2021 17:12:15 system,info router rebooted

Is here only way to install 7.1.1 netinstall option?
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Sun Jan 02, 2022 12:33 am

It may work when you remove the wireless package. It is a bug doing the upgrade from separate packages to combined package.
Of course first export the config so you can add it back later. And of course you cannot do this when the unit is remote and accessed over wireless.
 
User avatar
mkx
Forum Guru
Forum Guru
Posts: 11381
Joined: Thu Mar 03, 2016 10:23 pm

Re: v7.1.1 is released!

Sun Jan 02, 2022 1:02 am

Another thing to try before netinstalling: upload bundle (main) package for some recent v6 version (e.g. 6.48.6), set it to downgrade ROS (if uploaded version is lower than curently installed) and reboot. It should turn into bundled installation of ROS v6, which might allow for normal upgrade to v7
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Sun Jan 02, 2022 12:22 pm

Another thing to try before netinstalling: upload bundle (main) package for some recent v6 version (e.g. 6.48.6), set it to downgrade ROS (if uploaded version is lower than curently installed) and reboot. It should turn into bundled installation of ROS v6, which might allow for normal upgrade to v7
That doesn't work... the bug is actually in the 6.xx version which does not allow update from separate to bundle package and it affects both the upgrade to v7 and the change to bundle package within v6.
It appears to be introduced several versions ago. It only affects devices with 16MB flash (which unfortunately are many...)
 
dimnik70
just joined
Posts: 1
Joined: Thu Oct 25, 2018 10:58 am

RBSXTR 7.1.1

Sun Jan 02, 2022 2:04 pm

Modem sim select now missing
/system routerboard sim set sim-slot=down reply with error bad command name sim (line 1 column 21)



Found solution - you could change sim slot with /interface lte settings set sim-slot=a

Winbox: Interfaces -> LTE -> Modem -> SIM Slot
Last edited by dimnik70 on Mon Jan 03, 2022 12:01 pm, edited 2 times in total.
 
infabo
Long time Member
Long time Member
Posts: 585
Joined: Thu Nov 12, 2020 12:07 pm

Re: v7.1.1 is released!

Sun Jan 02, 2022 3:28 pm

Chateau running 5d without issues. Then suddenly the device locks up. Well done ROS. Very stable.
 
dg1kwa
just joined
Posts: 19
Joined: Tue Aug 17, 2010 12:32 pm
Location: Monheim

Re: v7.1.1 is released!

Tue Jan 04, 2022 9:59 am

Hi,
IGMP/MLD Snooping not work correct.
Unbenannt.PNG
All from ether1 but link on ether1 is down for more than 10 hours, why this entry never delete?

Thank and regards
Andreas
You do not have the required permissions to view the files attached to this post.
 
maaathieu
just joined
Posts: 3
Joined: Mon Aug 12, 2019 5:12 pm

Re: v7.1.1 is released!

Tue Jan 04, 2022 10:54 am

hi
are route filters by bgp-communities supposed to work in this release ?
I had a filter that used to work in v6, that has been converted like this:

rule="if (bgp-communities includes 11111:111 ) { set blackhole yes; accept; }"

but it does not work. I tried with a different condition and it works.

the "B" flag in the route list doesn't seem to exist anymore, and the fact that rejected routes still appear as inactive in the list is a little bit disturbing...

Thanks,

Mathieu
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Tue Jan 04, 2022 11:23 am

That kind of condition "if (bgp-communities includes 11111:111 )" works for me. Or do you mean the action "set blackhole yes" does not work? (I did not test that)
 
User avatar
evince
Member
Member
Posts: 353
Joined: Thu Jul 05, 2012 12:11 pm
Location: Harzé - Belgique
Contact:

Re: v7.1.1 is released!

Tue Jan 04, 2022 11:28 am

After upgrade to 7.1.1 from v6 i have an issue with l2tp+ipsec with error

<ip>: authentication failed: peer didn't respond to CHAP challenge
Same for me. if i disable ipsec, all is working.
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Tue Jan 04, 2022 11:39 am

I have two L2TP/IPsec clients with 7.1.1 and it works OK. Check what "Allow" protocols you have on the Advanced tab. Usually it should be mschap2 not mschap1.
Or are you using L2TP/IPsec as a server? Please be clear when reporting problems!
 
User avatar
evince
Member
Member
Posts: 353
Joined: Thu Jul 05, 2012 12:11 pm
Location: Harzé - Belgique
Contact:

Re: v7.1.1 is released!

Tue Jan 04, 2022 11:42 am

Hello pe1chl,

Thank your for your help.

My router woks as a L2TP/IPSec server. Sometimes my customers are able to connect with IPSec enabled, but I cannot join anything in their network. If I disable IPSec, I can join the whole network.

All was working before upgrading to ver.7.

Regards,
 
maaathieu
just joined
Posts: 3
Joined: Mon Aug 12, 2019 5:12 pm

Re: v7.1.1 is released!

Tue Jan 04, 2022 11:54 am

That kind of condition "if (bgp-communities includes 11111:111 )" works for me. Or do you mean the action "set blackhole yes" does not work? (I did not test that)
actually, I have two rules, like this:
 0   chain=filter-in rule="if (bgp-communities includes 11111:111 ) { set blackhole yes; accept; }" 
 1   chain=filter-in rule="reject;" 
like this, the result is:
   DIb   dst-address=23.135.225.0/24 routing-table=main gateway=1.1.1.1 immediate-gw=2.2.2.2%ether5_832 distance=20 scope=40 target-scope=30 suppress-hw-offload=no
for me it means that the route didn't match the first rule, and is matched by the second one.

if I change the condition like this
 0   chain=filter-in rule="if ( dst == 23.135.225.0/24) { set blackhole yes; accept; }" 

 1   chain=filter-in rule="reject;" 


I get
   DAb   dst-address=23.135.225.0/24 routing-table=main gateway=1.1.1.1 blackhole immediate-gw="" distance=20 scope=40 target-scope=30 suppress-hw-offload=no 
this time the route has been matched by the first rule and is blackholed.

I checked with a tcpdump catpure, the comminity is well set in the packet.

Mathieu
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Tue Jan 04, 2022 12:18 pm

I use rules like this:
"if (bgp-communities includes 44137:10050) { set bgp-local-pref 50; }"
and they work OK.
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Tue Jan 04, 2022 12:20 pm

My router woks as a L2TP/IPSec server. Sometimes my customers are able to connect with IPSec enabled, but I cannot join anything in their network. If I disable IPSec, I can join the whole network.
There must be a lot more going on than just running an L2TP/IPsec server when you can "join the whole network" of a client.
I am not going to help further when you play such hide-and-seek games. Best is to start a new topic and include your /export in that.
 
TedRule
just joined
Posts: 15
Joined: Tue Nov 03, 2020 4:41 pm

Re: v7.1.1 is released! CAKE / FQ_Codel Support

Tue Jan 04, 2022 12:44 pm

I've just upgraded one of my older RB2011 devices from 6.49 to 7.1.1, and all seems to have gone smoothly enough so far, so many thanks for that, although I have noted the missing
Wireless PSKs in the configuration export, and previous comments on the forum about IPSec identities being missing.

Nevertheless, I notice that that CAKE / FQ_Codel Queueing Disciplines don't appear to be offered in either the Web GUI or /queue/types/print. I presume that this is because of the lack of some
sort of hardware support. Is that true, or have I missed something obvious where a previously v6 device doesn't support this until I've done something?

In a wider context, is there perhaps a generic page somewhere which breaks down feature support by hardware type under v7?
 
maaathieu
just joined
Posts: 3
Joined: Mon Aug 12, 2019 5:12 pm

Re: v7.1.1 is released!

Tue Jan 04, 2022 12:57 pm

I use rules like this:
"if (bgp-communities includes 44137:10050) { set bgp-local-pref 50; }"
and they work OK.
is there a way to see what announces are received ?
i'd like to check if it detects the right communities, but I can find it anywhere

Thanks,

Mathieu
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released! CAKE / FQ_Codel Support

Tue Jan 04, 2022 1:39 pm

although I have noted the missing
Wireless PSKs in the configuration export, and previous comments on the forum about IPSec identities being missing.
This is two different topics:
1. the /export now does not include passwords and keys anymore unless you use the show-sensitive parameter. in v6 they were shown unless you used the hide-sensitive parameter.
2. the IPsec identities get lost on a reboot, at least in some undertermined circumstances. I have to paste them from an older export every time I reboot (as part of an upgrade, I do not reboot for other reasons)
 
User avatar
colinardo
just joined
Posts: 18
Joined: Sun Jan 08, 2017 9:02 pm

Re: v7.1.1 is released!

Tue Jan 04, 2022 1:40 pm

With 7.1.1. log entry is missing details what changed when adding/deleting/changing routing table entries :

screenshot.png
You do not have the required permissions to view the files attached to this post.
 
User avatar
mrz
MikroTik Support
MikroTik Support
Posts: 7038
Joined: Wed Feb 07, 2007 12:45 pm
Location: Latvia
Contact:

Re: v7.1.1 is released!

Tue Jan 04, 2022 1:59 pm

is there a way to see what announces are received ?
i'd like to check if it detects the right communities, but I can find it anywhere

Thanks,

Mathieu
routing route print detail
Will show all BGP attributes after input filters.
 
User avatar
eworm
Forum Guru
Forum Guru
Posts: 1070
Joined: Wed Oct 22, 2014 9:23 am
Location: Oberhausen, Germany
Contact:

Re: v7.1.1 is released!

Tue Jan 04, 2022 2:10 pm

Seems like Split-DNS regex matching for FWD functional doesn't work with enabled "Use DoH Server", all request immediately passed to DoH server. But for static records (TYPE A) with regex matching everything is ok, device reply regex matched answer.
It is like that since DoH and FWD exist in RouterOS... Sadly.
+1 for changing this, would like to use both at the same time.
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Tue Jan 04, 2022 2:29 pm

With 7.1.1. log entry is missing details what changed when adding/deleting/changing routing table entries :
It is like that for most of the new commands related to routing. Apparently someone still has to go over the logging functionality.
(logging for BGP events is mostly useless as well, it looks like internal debug logging instead of useful event logging for the user)
 
User avatar
bajodel
Long time Member
Long time Member
Posts: 551
Joined: Sun Nov 24, 2013 8:30 am
Location: Italy

Re: v7.1.1 is released!

Tue Jan 04, 2022 2:41 pm

Seems like Split-DNS regex matching for FWD functional doesn't work with enabled "Use DoH Server", all request immediately passed to DoH server. But for static records (TYPE A) with regex matching everything is ok, device reply regex matched answer.
+1 for using both at the same time.
 
maaathieu
just joined
Posts: 3
Joined: Mon Aug 12, 2019 5:12 pm

Re: v7.1.1 is released!

Tue Jan 04, 2022 3:19 pm

is there a way to see what announces are received ?
i'd like to check if it detects the right communities, but I can find it anywhere

Thanks,

Mathieu
routing route print detail
Will show all BGP attributes after input filters.

ok, so the community is correct:
 Fb   afi=ip4 contribution=filtered dst-address=23.135.225.0/24 routing-table=main gateway=1.1.1.1 immediate-gw=2.2.2.2%ether5_832 distance=20 scope=40 
       target-scope=30 belongs-to="BGP IP routes from 1.1.1.1" 
       bgp.peer-cache-id=*B000005 .as-path="11111" .communities=11111:111,no-export .atomic-aggregate=yes .origin=igp 
       debug.fwp-ptr=0x20302360 

could it be because there are two communities?

I tried with the condition "bgp-communities includes 11111:111,no-export" but it doesn't work either
 
User avatar
denisun
Frequent Visitor
Frequent Visitor
Posts: 81
Joined: Wed Jul 16, 2014 6:38 pm
Location: Greece

Re: v7.1.1 is released!

Tue Jan 04, 2022 6:01 pm

I have a RB4011.
When i download a torrent file i have ether down in PC which downloads.
The cpu/mem is normal.
I cant capture if done at the time of up or down full load
or when drop packets.
I tried to change the queue type but the problem is the same.
The log file catch
interface, info ether4 link down
interface, info ether4 link up (speed 1G, full duplex).
I searched the log file for previous records (prior 7.1 update) and i have not any in 6.X.
 
kiharapet
just joined
Posts: 20
Joined: Wed Apr 15, 2020 2:30 pm

Re: v7.1.1 is released!

Wed Jan 05, 2022 8:18 am

Hi
I have an RB2011 running 7.1.1
Today i was playing with my routes and I noticed something wierd with the UI when using winbox.
I have 2 routes when i disable the Primary the UI seems to hang at the back(actual) it has switched but the UI does not show (I assumed an issue at first and recreated the route before i realized)
when i disable route1 i get shows like it has not switched
mtik1r.png
i click rules then back to routes and its ok
then i enable the 1st route again i get looks like 2 routes are active
mtik2r.png
using winbox 3.31
You do not have the required permissions to view the files attached to this post.
 
shurik3
just joined
Posts: 5
Joined: Wed Jan 05, 2022 9:34 am

Re: v7.1.1 is released!

Wed Jan 05, 2022 9:38 am

Good Morning

I got 3 dead Hex S after Upgrade from 6.48/6.49 to 7.1/7.1.1
Did I something wrong? 2 of them were dead after restart (every 10 sek they restarted themselves)
1 of them was going dead after second restart...

after netinstall everything working, but very strange!

thank you
 
infabo
Long time Member
Long time Member
Posts: 585
Joined: Thu Nov 12, 2020 12:07 pm

Re: v7.1.1 is released!

Wed Jan 05, 2022 10:23 am

That's how it is. You did nothing wrong.
So you have a Backup from before upgrading? If yes, you Can you downgrade to 6.x, restore Backup and Upgrade again. If the Upgrade fails again, you have a reproducible upgrade-failure you can report to MT Support. This would help many people.
 
jn9
just joined
Posts: 2
Joined: Fri Oct 08, 2021 4:04 pm

Re: v7.1.1 is released!

Wed Jan 05, 2022 11:36 am

Updated CCR2004-16G-2S+ from 7.0.4 to 7.1.1 without a problem.
 
shurik3
just joined
Posts: 5
Joined: Wed Jan 05, 2022 9:34 am

Re: v7.1.1 is released!

Wed Jan 05, 2022 12:17 pm

That's how it is. You did nothing wrong.
So you have a Backup from before upgrading? If yes, you Can you downgrade to 6.x, restore Backup and Upgrade again. If the Upgrade fails again, you have a reproducible upgrade-failure you can report to MT Support. This would help many people.
unfortunately its production environment, no lab testing... so I just was f....d, yes, I had old backup.
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Wed Jan 05, 2022 12:32 pm

unfortunately its production environment, no lab testing... so I just was f....d, yes, I had old backup.
I would say that v7 is not ready for a production environment without lab testing, and where downtime is important.
Also it is always important to make a backup and this is listed as the first item in the start post of this topic.
"I hope you learned something" as Louis Rossmann would say.
 
shurik3
just joined
Posts: 5
Joined: Wed Jan 05, 2022 9:34 am

Re: v7.1.1 is released!

Wed Jan 05, 2022 12:47 pm

unfortunately its production environment, no lab testing... so I just was f....d, yes, I had old backup.
I would say that v7 is not ready for a production environment without lab testing, and where downtime is important.
Also it is always important to make a backup and this is listed as the first item in the start post of this topic.
"I hope you learned something" as Louis Rossmann would say.
well, I learned at last, that Mikrotik is not as good at quality management, as it assumed to be.
If I want to TEST something, I download BETA/RC.
Upgrade to a "stable" Version just make someone think - it IS stable.
But well, thank god I had a backup. Mikrotik should test little bit more, not me or someone else before making "stable" release.
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Wed Jan 05, 2022 1:08 pm

Well I would say that for any product, no matter if it is MikroTik or something else, before you perform a major version upgrade you should spend an hour on studying the matter by reading forums or other internet sources, then decide how much internal testing you want to do, and certainly not mass-deploy it before evaluation of a first try.
I run 7.1.1 on my own home router but I hit several things that I need to work around or are not fully functional and I reported them here on the forum and on the support portal. I certainly do not consider deploying it at work or on the AMPRnet (a larger network as a hobby that uses a lot of MikroTik equipment here).
But that is because I proceed carefully, I do not just run a "check for new version" and "download&install" for such a major upgrade on 3 or more routers.

Also you have to understand (most people don't) that "stable" does not refer to the stability of the device after this software has been installed, but to the type of release. It means that there will not be updates every day as there is in a BETA or RC version and that it is not full of experimental untested/unfinished stuff.
Now I agree with you that MikroTik violated that (there is some experimental and unfinished stuff in v7) but it is quite localized in the entire scope of things.
Also there are known problems with the updating procedure that would not affect a fresh install, as you noticed.
 
infabo
Long time Member
Long time Member
Posts: 585
Joined: Thu Nov 12, 2020 12:07 pm

Re: v7.1.1 is released!

Wed Jan 05, 2022 2:51 pm

Compared to a beta release from a year ago like 7.1beta3, this stable version is really rock solid stable. In the relative view. ;)
 
User avatar
denisun
Frequent Visitor
Frequent Visitor
Posts: 81
Joined: Wed Jul 16, 2014 6:38 pm
Location: Greece

Re: v7.1.1 is released!

Wed Jan 05, 2022 3:00 pm

I have a RB4011.
When i download a torrent file i have ether down in PC which downloads.
The cpu/mem is normal.
I cant capture if done at the time of up or down full load
or when drop packets.
I tried to change the queue type but the problem is the same.
The log file catch
interface, info ether4 link down
interface, info ether4 link up (speed 1G, full duplex).
I searched the log file for previous records (prior 7.1 update) and i have not any in 6.X.
I made some test with bandwidth test v.0.1.
protocol: udp
local Tx size: 1500
remote Tx size: 1500
direction: receive
local Tx speed: 1 Gbps
remote Tx speed: 1 Gbps
connection count: 20

Some times my pc ether disconnect and some times all ethers disconnect.
I tried with smaller Tx size, direction, speeds and connections count.
I have the same results.
Additionally i disable auto negotiate, but i have, again, the same results.
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Wed Jan 05, 2022 4:33 pm

I see no such issues on my RB4011... running 7.1.1 as well. Never seen an ethernet port going down for no reason. All my ethernet ports have last link up time on Dec 21 except one for which the device was rebooted.
 
RajaMani
just joined
Posts: 7
Joined: Wed Mar 16, 2011 7:42 pm

Re: v7.1.1 is released!

Wed Jan 05, 2022 5:14 pm

Hello

There is problem in PPPOE section. In interface all users are showing correctlybut in PPP active connection it showing double. Screenshot is attached. Checked in various time on RB4011.
MKT.jpg
You do not have the required permissions to view the files attached to this post.
 
User avatar
dll2003
newbie
Posts: 28
Joined: Sun Feb 16, 2020 11:35 am
Location: Moscow, Russia
Contact:

Re: v7.1.1 is released!

Wed Jan 05, 2022 6:00 pm

Hi all
Please tell me where you can read about changing the syntax of console commands in version 7.1.1?
I updated my hAP mini to 7.1.1 via netinstall and now I see a strange effect in the console, for example, I can not get help on command:
[admin@MikroTik] > export ?
expected end of command (line 1 column 8)
[admin@MikroTik] >

I'm trying to export the configuration to a file, but the export hangs constantly(
Thanks for advice.
 
User avatar
bajodel
Long time Member
Long time Member
Posts: 551
Joined: Sun Nov 24, 2013 8:30 am
Location: Italy

Re: v7.1.1 is released!

Wed Jan 05, 2022 6:11 pm

@dll2003

/export show-sensitive file=TheNameOfTheFileYouWant

command [F1] << for inline help
 
infabo
Long time Member
Long time Member
Posts: 585
Joined: Thu Nov 12, 2020 12:07 pm

Re: v7.1.1 is released!

Wed Jan 05, 2022 7:53 pm

Export is running for very long on e.g. SMIPS devices. Mostly because of errors.

Help is F1 now. No more "?"
 
za7
just joined
Posts: 18
Joined: Tue Mar 14, 2017 8:59 pm

Re: v7.1.1 is released!

Wed Jan 05, 2022 10:02 pm

Will RouterOS v7 get more frequent Linux Kernel updates than RouterOS v6?
 
User avatar
mkx
Forum Guru
Forum Guru
Posts: 11381
Joined: Thu Mar 03, 2016 10:23 pm

Re: v7.1.1 is released!

Wed Jan 05, 2022 10:20 pm

Will RouterOS v7 get more frequent Linux Kernel updates than RouterOS v6?

Inshallah
 
maxpage
newbie
Posts: 27
Joined: Sun Jul 15, 2018 7:01 pm

Re: v7.1.1 is released!

Wed Jan 05, 2022 11:14 pm

1. SSH client does not work:
[admin@mt] > /system/ssh 10.110.12.253 user=admin
connectHandler: Operation timed out
2. Watchdog timer does not work (CRS317-1G-16S+)
couldn't change watchdog - failed to enable watchdog timer (6)
 
infabo
Long time Member
Long time Member
Posts: 585
Joined: Thu Nov 12, 2020 12:07 pm

Re: v7.1.1 is released!

Wed Jan 05, 2022 11:40 pm

I would recommend Mikrotik to create a wiki page containing all relevant changes when upgrading from V6 to v7. Not everybody has to ask the same questions all over again.
Even the small changes like "?" on CLI or the invertion of hide-sensitive to show-sensitive of export command.
Name the breaking changes and don't let people left in the dark.
 
rcadmin
Posts: 0
Joined: Thu Jan 06, 2022 4:41 am

Re: v7.1.1 is released!

Thu Jan 06, 2022 4:46 am

I have tried to implement a recursive route (like in ros v6), but I don't see it working, unless the syntax has completely changed.
The route gets IUSH as invalid and unreachable.
Is this not implemented yet in ros v7.1.1 ?


Having the same issues have you had any luck figuring out a fix?
 
User avatar
rumahnetmks
Frequent Visitor
Frequent Visitor
Posts: 56
Joined: Mon Dec 21, 2020 10:00 am

Re: v7.1.1 is released!

Thu Jan 06, 2022 3:15 pm

Hello

There is problem in PPPOE section. In interface all users are showing correctlybut in PPP active connection it showing double. Screenshot is attached. Checked in various time on RB4011.

MKT.jpg
I have this error but it seem Winbox bug things. If u see the list with using terminal, it wont get double.
 
RohanAJoshi
Frequent Visitor
Frequent Visitor
Posts: 56
Joined: Thu Jun 10, 2021 12:29 pm

Re: v7.1.1 is released!

Thu Jan 06, 2022 3:28 pm

Ccr 1009 reboots by kernel failure in 4 to 5 days gap. Ticket open from week ( SUP-69940 ) no response.
Ccr 2004 reboots in 7 to 9 days by watchdog timer. Ticket open from 6 months, no resolution till now.
Very good release mikrotik. 👍
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Thu Jan 06, 2022 5:30 pm

I have this error but it seem Winbox bug things. If u see the list with using terminal, it wont get double.
I have had issues with double or invalid information shown in winbox and I was told to press F5 in such cases.
A bit strange because I never had comparable issues with RouterOS v6, but it appears that the constant automatic refresh of information in (most) winbox windows was removed in v7.
 
n1am
just joined
Posts: 16
Joined: Tue Nov 04, 2014 12:00 pm

Re: v7.1.1 is released!

Thu Jan 06, 2022 5:42 pm

Seems like Split-DNS regex matching for FWD functional doesn't work with enabled "Use DoH Server", all request immediately passed to DoH server. But for static records (TYPE A) with regex matching everything is ok, device reply regex matched answer.
+1

I can confirm this behaviour. If you use FWD record type in the static DNS entries you need to disable DoH.
 
kwjennings
just joined
Posts: 22
Joined: Tue Mar 07, 2017 4:59 pm

Re: v7.1.1 is released!

Thu Jan 06, 2022 7:59 pm

I am a "noobie" with a simple home network
I have an RB 4011 with two cAPs managed from the 4011 using CapsMan. All are on the latest release (V6.49.2)
This works very well in our home. It is FAAAASSST and stable.
What possible benefits might a home user such as myself see if I were to upgrade to V7?
Why would I take the risk of upgrading to V7?
 
holvoetn
Forum Guru
Forum Guru
Posts: 5320
Joined: Tue Apr 13, 2021 2:14 am
Location: Belgium

Re: v7.1.1 is released!

Thu Jan 06, 2022 8:01 pm

If your current setups works and you do not need any of the new features, don't change.
 
mac112
just joined
Posts: 15
Joined: Sat Jul 19, 2014 9:05 am
Location: Repubblica Ceca

Re: v7.1.1 is released!

Thu Jan 06, 2022 8:47 pm

From when it will support Dual core AMD G-T48E
I have a WYSE D10DP
 
mac112
just joined
Posts: 15
Joined: Sat Jul 19, 2014 9:05 am
Location: Repubblica Ceca

Re: v7.1.1 is released!

Thu Jan 06, 2022 8:50 pm

Atom 270N does not work
 
Rfulton
Frequent Visitor
Frequent Visitor
Posts: 99
Joined: Tue Aug 08, 2017 2:17 am

Re: v7.1.1 is released!

Thu Jan 06, 2022 9:23 pm

Hairpin Nat Broken.
 
User avatar
BartoszP
Forum Guru
Forum Guru
Posts: 2855
Joined: Mon Jun 16, 2014 1:13 pm
Location: Poland

Re: v7.1.1 is released!

Thu Jan 06, 2022 10:00 pm

Atom 270N does not work
Hairpin Nat Broken.
It definitely would help if you provide more details to describe problems.
Do you ask your doctor for help saying "I'm feeling ill"? :)
 
User avatar
Hejsan
just joined
Posts: 8
Joined: Mon Jun 23, 2014 5:16 am
Location: Tbilisi, Georgia
Contact:

Re: v7.1.1 is released!

Thu Jan 06, 2022 10:22 pm

Hairpin NAT is working fine on my hAP AC / RB3011UiAS-RM / RB1100AHx4 / RB2011UiAS-iN / RB951G-2HnD Routers. No single problem since upgrading from v6.49.2 to v7.1.1
 
Rfulton
Frequent Visitor
Frequent Visitor
Posts: 99
Joined: Tue Aug 08, 2017 2:17 am

Re: v7.1.1 is released!

Fri Jan 07, 2022 12:24 am

Atom 270N does not work
Hairpin Nat Broken.
It definitely would help if you provide more details to describe problems.
Do you ask your doctor for help saying "I'm feeling ill"? :)
I typically only report problems anymore because I'm around 0-10 of getting a fix, but here is the forum post.

viewtopic.php?p=903577
 
mac112
just joined
Posts: 15
Joined: Sat Jul 19, 2014 9:05 am
Location: Repubblica Ceca

Re: v7.1.1 is released!

Fri Jan 07, 2022 10:26 am

Atom 270N does not work
Hairpin Nat Broken.
It definitely would help if you provide more details to describe problems.
Do you ask your doctor for help saying "I'm feeling ill"? :)
Still writing "Calculating download size ..."
You do not have the required permissions to view the files attached to this post.
 
elbob2002
Member Candidate
Member Candidate
Posts: 252
Joined: Tue May 15, 2018 8:15 pm
Location: Ireland

Re: v7.1.1 is released!

Fri Jan 07, 2022 12:48 pm



It definitely would help if you provide more details to describe problems.
Do you ask your doctor for help saying "I'm feeling ill"? :)
Still writing "Calculating download size ..."
You need to remove any extra packages installed before upgrading. This has been mentioned in nearly every 7.x release post.
 
User avatar
mrz
MikroTik Support
MikroTik Support
Posts: 7038
Joined: Wed Feb 07, 2007 12:45 pm
Location: Latvia
Contact:

Re: v7.1.1 is released!

Fri Jan 07, 2022 12:59 pm

FYI the next ROS version will have the "ignore-missing" option to help in cases when one of the installed packages does not exist anymore.
 
elgrandiegote
newbie
Posts: 40
Joined: Tue Feb 05, 2013 6:02 am
Location: Buenos Aires, Argentina

Re: v7.1.1 is released!

Fri Jan 07, 2022 4:20 pm

I did a lot of tests on openvpn (udp)
The results are definite.
openvpn udp protocol: (It has many bugs)
max connect time per client ( 1 hours or 01:01:00)
os client: windows , android , ios
all client (ovpn udp) They are disconnect after 61 minutes
After 1 hour and 1 minute openvpn disconnected.
I emphasize that the problems are only in udp protocol.

create ticket in mikrotik support (SUP-57401)
But the mikrotik support team did not care


emils , mrz or normis please answer.

my home router has an openvpn implementation with lzo, udp, and 100% stable, too bad mikrotik doesn't care
 
llpax
just joined
Posts: 3
Joined: Tue Dec 07, 2021 11:57 pm
Location: Belarus

Re: v7.1.1 is released!

Fri Jan 07, 2022 6:36 pm

sorry. 7.1.1 unusable: x3 cpu load
1. clear FW (only src-nat), no ip-lists.
ros7_emptyfw.jpg
2. and full config (filer + mange + nat) + Queue tree
ros7_3011.jpg
3 .VS ros6 full config (filer + mange + nat) + Queue tree
ros6_3011.jpg
You do not have the required permissions to view the files attached to this post.
 
jult
Frequent Visitor
Frequent Visitor
Posts: 52
Joined: Sat Dec 26, 2020 1:16 am

Re: v7.1.1 is released! CAKE / FQ_Codel Support

Fri Jan 07, 2022 9:49 pm

Nevertheless, I notice that that CAKE / FQ_Codel Queueing Disciplines don't appear to be offered in either the Web GUI or /queue/types/print.
I would like some more info on cake / fq_codel queueing as well. For instance, isn't it about time some of the defaults are using those queue types by now? The upgrade to 7.* does not seem to have changed any of them in my devices;
2021-07-24_213119_cr.png
I would very much like to know which I can change to cake and/or fq_codel now. Any advice on this? It's not in the wiki (yet)..
You do not have the required permissions to view the files attached to this post.
 
mhaluska
just joined
Posts: 22
Joined: Sat Jun 13, 2020 1:20 pm

Re: v7.1.1 is released!

Fri Jan 07, 2022 11:35 pm

Just define new type...
> /queue/type/add kind=[TAB]
bfifo  cake  codel  fq-codel  mq-pfifo  none  pcq  pfifo  red  sfq
 
jult
Frequent Visitor
Frequent Visitor
Posts: 52
Joined: Sat Dec 26, 2020 1:16 am

Re: v7.1.1 is released!

Sat Jan 08, 2022 12:54 am

Just define new type...
> /queue/type/add kind=[TAB]
bfifo  cake  codel  fq-codel  mq-pfifo  none  pcq  pfifo  red  sfq
That's not the question, I see it listed among the types. I'm curious why it's not being used..
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Sat Jan 08, 2022 1:34 am

1. it isn't stable and finished
2. it is likely not the optimal type for the usage scenarios hinted by the type name
you would use such queues e.g. on an internet link, so maybe in the future there will be a type name for that?
even then of course it only is used when you select it.
 
denasu
just joined
Posts: 1
Joined: Wed Apr 29, 2020 10:32 pm

Re: v7.1.1 is released!

Sat Jan 08, 2022 11:06 am

I have a hap ac2 with version 7.1.1 when i turn it off via winbox then it turns on again in this version
The same problem with hAP ac3. I tried on versions 7.1, 7.1.1, 7.2rc1. Version 6.49.2 turns off successfully. (SUP-71006)
 
mac112
just joined
Posts: 15
Joined: Sat Jul 19, 2014 9:05 am
Location: Repubblica Ceca

Re: v7.1.1 is released!

Sat Jan 08, 2022 11:33 am



Still writing "Calculating download size ..."
You need to remove any extra packages installed before upgrading. This has been mentioned in nearly every 7.x release post.
I used system and dhcp.
It still writes "Calculating download size ..."
You do not have the required permissions to view the files attached to this post.
 
jult
Frequent Visitor
Frequent Visitor
Posts: 52
Joined: Sat Dec 26, 2020 1:16 am

Re: v7.1.1 is released!

Sat Jan 08, 2022 12:35 pm

1. it isn't stable and finished
2. it is likely not the optimal type for the usage scenarios hinted by the type name you would use such queues
Hmm.. I strongly disagree there. I've been part of the bufferbloat testers for over a decade now. fq_codel can be enabled for everything you'd like to try it on, and would probably already yield better results than the older current queue types. CAKE has also been widely tested and usually ends up better than sfq for wifi, even with CAKE defaults, but hey. If you mean to say you have not tested them with mikrotik hardware, I'd say go ahead and try. Try default to fq_codel for the internet port and run some tests. Switch all Flow Control to Off for that port (Interfaces > Ethernet > Tx and Rx Flow Control > Off), and maybe default to CAKE for wireless facing interface(s) and run some tests and compare.
 
pe1chl
Forum Guru
Forum Guru
Posts: 10183
Joined: Mon Jun 08, 2015 12:09 pm

Re: v7.1.1 is released!

Sat Jan 08, 2022 12:48 pm

Hmm.. I strongly disagree there. I've been part of the bufferbloat testers for over a decade now. fq_codel can be enabled for everything you'd like to try it on, and would probably already yield better results than the older current queue types.
But you can do that, right? The existing queue type names are for purposes like a plain (local) ethernet interface, a WiFi interface, etc.
I don't think it is useful to put some advanced queue on there, e.g. for ethernet.

When you want to use these queues on the internet port, just add your queue type for it and use it.
I have not yet tried it on my router as I read regular reports of routers crashing and about missing features (queue direction) so I wait until it stabilizes a little.
I use a queue tree with DSCP-determined priority and it serves me well enough.
 
haedertowfeq
just joined
Posts: 15
Joined: Thu Nov 19, 2020 5:58 pm

Re: v7.1.1 is released!

Sat Jan 08, 2022 5:28 pm

Can you share your configure
 
mducharme
Trainer
Trainer
Posts: 1777
Joined: Tue Jul 19, 2016 6:45 pm
Location: Vancouver, BC, Canada

Re: v7.1.1 is released!

Sat Jan 08, 2022 6:19 pm

I used system and dhcp.
It still writes "Calculating download size ..."
You have to download the npk and upgrade that way. There is no "dhcp" or "system" package in RouterOS v7 and so it can't find those package to download, which is why it is stuck at "calculating download size". You can only upgrade normally to RouterOS v7 when the bundle package was used in RouterOS v6. You have used the individual packages instead of the bundle.
 
sstybel
just joined
Posts: 6
Joined: Fri Jun 05, 2020 10:13 pm
Location: Poland

Re: v7.1.1 is released!

Sat Jan 08, 2022 8:11 pm

I have a problem with ROS version 7.1.1. on wAP ac old devices (RBwAPG-5HacT2HnD on mipsbe). The problem mainly concerns 5G WiFi and is manifested by a decrease in speed towards the upload. The problem does not occur on wAP ac new (RBwAPG-5HacD2HnD on arm). I did not observe the problem on hAP ac3 (RBD53iG-5HacHnD on arm). After downgrading to 6.49.2 the problem disappears and even wAP ac new (RBwAPG-5HacD2HnD on arm) and hAP ac3 (RBD53iG-5HacHnD on arm) work better (more efficiently). The screenshot shows an example of 5G WiFi transfer for a 600/60 Mbps Internet connection. The same problem is in the internal network, e.g. when copying files via WiFi to a NAS in the LAN network (even the WiFi connection is broken / disconnected).
mt-error.jpg
You do not have the required permissions to view the files attached to this post.
 
Pomo
just joined
Posts: 14
Joined: Sat Feb 06, 2016 10:09 pm

Re: v7.1.1 is released!

Sun Jan 09, 2022 3:28 am

HAP AC RouterBOARD 962UiGS-5HacT2HnT on 7.1.1, 5GHz wifi when set to 5500, 20/40/80 a/n/ac, Ceee it is impossible to connect to.
Same setting I have on Hap AC2 and AC3 on 7.1.1., and it works fine.
Also, quick set, now there is no check for updates buton?
 
mafiosa
Member Candidate
Member Candidate
Posts: 266
Joined: Fri Dec 09, 2016 8:10 pm
Location: Kolkata, India
Contact:

Re: v7.1.1 is released!

Sun Jan 09, 2022 10:02 am

Does RouterOS support multiple routing tables for IPv6?
 
User avatar
osc86
Member Candidate
Member Candidate
Posts: 197
Joined: Wed Aug 09, 2017 1:15 pm

Re: v7.1.1 is released!

Sun Jan 09, 2022 3:01 pm

they are just tables, you can use IPv4 and IPv6 routes with them. For adding IPv6 routes to a table other than main, you currently have to use the cli, winbox still doesn't show the routing-table parameter.
 
gotsprings
Forum Guru
Forum Guru
Posts: 2087
Joined: Mon May 14, 2012 9:30 pm

Re: v7.1.1 is released!

Sun Jan 09, 2022 4:03 pm

I have this error but it seem Winbox bug things. If u see the list with using terminal, it wont get double.
I have had issues with double or invalid information shown in winbox and I was told to press F5 in such cases.
A bit strange because I never had comparable issues with RouterOS v6, but it appears that the constant automatic refresh of information in (most) winbox windows was removed in v7.
So that's what that is. When I was working in wireless I saw an entry for the AP 2 times. It showed as the old routerOS and New. Closed windobx and reopened. Duplicates gone.
 
infabo
Long time Member
Long time Member
Posts: 585
Joined: Thu Nov 12, 2020 12:07 pm

Re: v7.1.1 is released!

Sun Jan 09, 2022 4:04 pm

Also, quick set, now there is no check for updates buton?
Sure there is one.

Who is online

Users browsing this forum: AndiiiHD, holvoetn and 22 guests