My problem:
An RBD52G-5HacD2HnD
Firmware Type ipq4000L
Factory Firmware 6.45.9
Current Firmware 6.47.9
Code: Select all
[admin@MikroTik] > /interface print
Flags: D - dynamic, X - disabled, R - running, S - slave
# NAME TYPE ACTUAL-MTU L2MTU MAX-L2MTU MAC-ADDRESS
0 R ether1 ether 1500 1598 9214 2C:C8:1B:EE:A0:87
1 S ether2 ether 1500 1598 9214 2C:C8:1B:EE:A0:88
2 RS ether3 ether 1500 1598 9214 2C:C8:1B:EE:A0:89
3 S ether4 ether 1500 1598 9214 2C:C8:1B:EE:A0:8A
4 S ether5 ether 1500 1598 9214 2C:C8:1B:EE:A0:8B
5 wlan1 wlan 1500 1600 2290 2C:C8:1B:EE:A0:8C
6 X wlan2 wlan 1500 1600 2290 2C:C8:1B:EE:A0:8D
7 wlan3 wlan 1500 1600 2290 2E:C8:1B:EE:A0:8C
8 R ;;; defconf
bridge bridge 1500 1598 2C:C8:1B:EE:A0:88
9 X bridge1 bridge 2C:C8:1B:EE:A0:8C
[admin@MikroTik] > /interface bridge print
Flags: X - disabled, R - running
0 R ;;; defconf
name="bridge" mtu=auto actual-mtu=1500 l2mtu=1598 arp=reply-only arp-timeout=auto mac-address=2C:C8:1B:EE:A0:88 protocol-mode=rstp fast-forward=yes igmp-snooping=no
auto-mac=no admin-mac=2C:C8:1B:EE:A0:88 ageing-time=5m priority=0x8000 max-message-age=20s forward-delay=15s transmit-hold-count=6 vlan-filtering=no dhcp-snooping=no
1 X name="bridge1" mtu=1500 arp=enabled arp-timeout=auto mac-address=2C:C8:1B:EE:A0:8C protocol-mode=rstp fast-forward=yes igmp-snooping=no auto-mac=yes ageing-time=5m
priority=0x8000 max-message-age=20s forward-delay=15s transmit-hold-count=6 vlan-filtering=no dhcp-snooping=no
[admin@MikroTik] > /interface bridge port print
Flags: X - disabled, I - inactive, D - dynamic, H - hw-offload
# INTERFACE BRIDGE HW PVID PRIORITY PATH-COST INTERNAL-PATH-COST HORIZON
0 I H ;;; defconf
ether2 bridge yes 1 0x80 10 10 none
1 H ;;; defconf
ether3 bridge yes 1 0x80 10 10 none
2 I H ;;; defconf
ether4 bridge yes 1 0x80 10 10 none
3 I H ;;; defconf
ether5 bridge yes 1 0x80 10 10 none
[admin@MikroTik] > /ip address print
Flags: X - disabled, I - invalid, D - dynamic
# ADDRESS NETWORK INTERFACE
0 ;;; defconf
192.168.88.1/24 192.168.88.0 wlan1
1 10.1.99.2/16 10.1.0.0 bridge
[admin@MikroTik] > /ip arp print
Flags: X - disabled, I - invalid, H - DHCP, D - dynamic, P - published, C - complete
# ADDRESS MAC-ADDRESS INTERFACE
0 C 10.1.254.255 00:50:56:A8:11:29 bridge
1 C 10.1.240.131 7C:10:C9:84:C2:94 bridge
[admin@MikroTik] > /ip route print
Flags: X - disabled, A - active, D - dynamic, C - connect, S - static, r - rip, b - bgp, o - ospf, m - mme, B - blackhole, U - unreachable, P - prohibit
# DST-ADDRESS PREF-SRC GATEWAY DISTANCE
0 S 0.0.0.0/0 81.xx.xx.43 ether1 1
1 A S 10.1.0.0/16 bridge 1
2 ADC 81.xx.xx.40/29 10.1.99.2 bridge 0
3 S 81.xx.xx.40/29 81.xx.xx.43 ether1 1
4 DC 192.168.88.0/24 192.168.88.1 wlan1 255
Why, and how can I flush this dynamic false route.
At the past I added IP address 81.xx.xx.43/29 to ether1 (and a static route too, to override the false route) but later i removed to router flush this dynamic route... but not.
I _do not_ want to reboot the device.
Thanks a lot,
Gergely