Good day.
We've noticed some issues on one small site that was deployed years ago. We are currently using an omnitik as a wireless hub with an incoming and outgoing feed off it. Please see attached photo for the basic network diagram. We understand that the duty cycle can be a big factor in this problem as the omni can only transmit or receive at a time.
The question is, is there a configuration (without adding gear immediately) on the omni or sxts (stations) to optimise the network? With fibre installed on the site, it will stick out like a sore thumb.
Below is the config for the omni, thanks guys/gals!
Code: Select all
# jun/27/2022 09:57:45 by RouterOS 6.46.2
# software id = FFB2-GQED
#
# model = OmniTIK UPA-5HnD
# serial number = 4C9B0435392F
/interface bridge
add admin-mac=E4:8D:8C:DC:3C:F8 auto-mac=no fast-forward=no name=bridge
/interface ethernet
set [ find default-name=ether1 ] advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full mac-address=E4:8D:8C:DC:3C:F8
set [ find default-name=ether2 ] advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full comment=RocketM2 mac-address=E4:8D:8C:DC:3C:F9
set [ find default-name=ether3 ] advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full comment=NanoM2 mac-address=E4:8D:8C:DC:3C:FA poe-out=forced-on
set [ find default-name=ether4 ] advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full mac-address=E4:8D:8C:DC:3C:FB poe-out=forced-on
set [ find default-name=ether5 ] advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full mac-address=E4:8D:8C:DC:3C:FC
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
add authentication-types=wpa2-psk eap-methods="" management-protection=allowed mode=dynamic-keys name=pass supplicant-identity=""
add authentication-types=wpa2-psk eap-methods="" management-protection=allowed mode=dynamic-keys name=passcam supplicant-identity=""
/interface wireless
set [ find default-name=wlan1 ] band=5ghz-onlyn channel-width=20/40mhz-Ce country="new zealand" disabled=no frequency=5600 frequency-mode=superchannel hide-ssid=yes ht-basic-mcs=mcs-0,mcs-1,mcs-2,mcs-3 ht-supported-mcs=\
mcs-0,mcs-1,mcs-2,mcs-3,mcs-4,mcs-5,mcs-6,mcs-7,mcs-8,mcs-9,mcs-10,mcs-11,mcs-16,mcs-17,mcs-18,mcs-19,mcs-20,mcs-21,mcs-22,mcs-23 mode=ap-bridge name=wlan2 nv2-security=enabled radio-name=omni-laundry security-profile=pass ssid=link-laundry \
wireless-protocol=nv2
/interface wireless nstreme
set wlan2 enable-nstreme=yes
/ip ipsec proposal
set [ find default=yes ] enc-algorithms=aes-128-cbc
/snmp community
set [ find default=yes ] addresses=0.0.0.0/0
/interface bridge port
add bridge=bridge hw=no interface=ether1
add bridge=bridge hw=no interface=ether2
add bridge=bridge hw=no interface=ether3
add bridge=bridge hw=no interface=ether4
add bridge=bridge hw=no interface=ether5
add bridge=bridge interface=wlan2
/ip address
add address=10.5.50.230/24 interface=bridge network=10.5.50.0
/ip dns
set servers=8.8.8.8
/ip route
add distance=1 gateway=10.5.50.1
/ip ssh
set allow-none-crypto=yes forwarding-enabled=remote
/system clock
set time-zone-autodetect=no time-zone-name=Pacific/Auckland
/system identity
set name=omni-laundry