i have a problem with TPLINK CPE710 in client mode. I am using mikrotik SXT SA 5GHz 866MHz as an access point and CPE710 as a client which is hardwired to my PC. I am trying to establish a faster connect to SXT AP with at least 40MHz or 80MHz channel width but I am unable to do so. It is always locking me at 20MHz channel width on mikrotik no matter what.
This is my config:
Code: Select all
# oct/14/2022 20:25:32 by RouterOS 6.49.6
# software id = 0LCV-L3CB
#
# model = SXT G-5HPacD r2
# serial number =
/interface bridge
add name=bridge
/interface list
add comment=defconf name=WAN
add comment=defconf name=LAN
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
add authentication-types=wpa2-psk eap-methods="" group-key-update=1h5m mode=\
dynamic-keys name=profile1 supplicant-identity="" wpa-pre-shared-key=\
1234567890 wpa2-pre-shared-key=1234567890
/interface wireless
set [ find default-name=wlan1 ] band=5ghz-a/n/ac channel-width=\
20/40/80mhz-eCee country="etsi 5.7-5.8 srd" disabled=no frequency=5795 \
frequency-mode=superchannel installation=outdoor mode=ap-bridge \
radio-name=JUST_TEST security-profile=profile1 ssid=TEST_WIFI wmm-support=\
enabled
/ip dhcp-server
add add-arp=yes address-pool=default-dhcp interface=wlan1 name=defconf
/interface bridge port
add bridge=bridge comment=defconf interface=ether1
add bridge=bridge comment=defconf interface=wlan1
/ip neighbor discovery-settings
set discover-interface-list=LAN
/interface list member
add comment=defconf interface=ether1 list=LAN
add comment=defconf interface=wlan1 list=WAN
/ip address
add address=192.168.66.200/24 comment=defconf interface=ether1 network=\
192.168.66.0
/ip dhcp-client
add comment=defconf interface=bridge
/ip dhcp-server network
add address=192.168.66.0/24 comment=defconf dns-server=192.168.66.1 gateway=\
192.168.66.1
/ip dns
set allow-remote-requests=yes servers=192.168.66.1
/ip dns static
add address=192.168.66.1 comment=defconf name=router.lan
/ip firewall filter
add action=accept chain=input comment=\
"defconf: accept established,related,untracked" connection-state=\
established,related,untracked disabled=yes
add action=drop chain=input comment="defconf: drop invalid" connection-state=\
invalid disabled=yes
add action=accept chain=input comment="defconf: accept ICMP" disabled=yes \
protocol=icmp
add action=accept chain=input comment=\
"defconf: accept to local loopback (for CAPsMAN)" dst-address=127.0.0.1
add action=drop chain=input comment="defconf: drop all not coming from LAN" \
disabled=yes in-interface-list=!LAN
add action=accept chain=forward comment="defconf: accept in ipsec policy" \
ipsec-policy=in,ipsec
add action=accept chain=forward comment="defconf: accept out ipsec policy" \
ipsec-policy=out,ipsec
add action=fasttrack-connection chain=forward comment="defconf: fasttrack" \
connection-state=established,related
add action=accept chain=forward comment=\
"defconf: accept established,related, untracked" connection-state=\
established,related,untracked
add action=drop chain=forward comment="defconf: drop invalid" \
connection-state=invalid disabled=yes
add action=drop chain=forward comment=\
"defconf: drop all from WAN not DSTNATed" connection-nat-state=!dstnat \
connection-state=new disabled=yes in-interface-list=WAN
/ip firewall nat
add action=masquerade chain=srcnat comment="defconf: masquerade" \
ipsec-policy=out,none out-interface-list=WAN
/ip route
add distance=1 gateway=192.168.66.1
/tool mac-server
set allowed-interface-list=LAN
/tool mac-server mac-winbox
set allowed-interface-list=LAN
Any ideas what could be wrong? Are they incompatible maybe?