I have recently purchased a RB5009UPr+S+IN (https://mikrotik.com/product/rb5009upr_s_in) and configrued it tonight. I have this powered by a CISCO SG250-08HP POE Switch with POE power being sent though ether1. Its has a bond (LACP) with ether1 and ether2 going back to the CISCO switch for my LAN as I don't have 2.5Gb/s LAN POE switches yet.
Everything is operating correctly, but I have noticed a warning which is now spamming the log every few mins and is coming from every port which is saying:
Code: Select all
etherX detected poe-out status: no_valid_psu
etherX detected poe-out status: disabled
I have made sure that all ports have POE set to OFF but the messages keeps coming, despite the router staying online/powered up.
I am running 7.6 latest stable release of ROS. Also the routerboard firmware is also running 7.6.
Is there away to stop these messages, or is something I have forgotten to do? or maybe a bug?
Summery
ether1 and ether2 connected to CISCO POE switch.
Power is being sent on both but I believe its only working into ether1 (from what I can see this is normal even on this version)
Below is a full copy of my running config, just with a few bits XX or YY out, but nothing which would make the config unreadable.
Code: Select all
# nov/21/2022 21:43:21 by RouterOS 7.6
# software id = JJNA-ABWH
#
# model = RB5009UPr+S+
# serial number = XXXXXXX
/interface bridge
add admin-mac=18:FD:XX:XX:XX:XX auto-mac=no disabled=yes name=bridge
/interface ethernet
set [ find default-name=ether1 ] comment="CISCO | SW01 | LAG| PORT 1" poe-out=off
set [ find default-name=ether2 ] comment="CISCO | SW01 | LAG | PORT 2" poe-out=off
set [ find default-name=ether3 ] disabled=yes poe-out=off
set [ find default-name=ether4 ] disabled=yes poe-out=off
set [ find default-name=ether5 ] disabled=yes poe-out=off
set [ find default-name=ether6 ] disabled=yes poe-out=off
set [ find default-name=ether7 ] disabled=yes poe-out=off
set [ find default-name=ether8 ] disabled=yes poe-out=off
set [ find default-name=sfp-sfpplus1 ] comment="City Fibre | ONT"
/interface vlan
add comment="Briant Broadband | VLAN" interface=sfp-sfpplus1 name=vlan911 vlan-id=911
/interface bonding
add comment="CISCO | SW01 | LCAP" mode=802.3ad name=bond0 slaves=ether1,ether2 transmit-hash-policy=layer-2-and-3
/interface pppoe-client
add add-default-route=yes comment="Briant Broadband | Internet" disabled=no interface=vlan911 name=pppoe0 use-peer-dns=yes user=XXXXXXXXXX
/interface vlan
add comment="Core | Network" interface=bond0 name=vlan2910 vlan-id=2910
add comment="Trusted | Network" interface=bond0 name=vlan2920 vlan-id=2920
add comment="Work | Network" interface=bond0 name=vlan2930 vlan-id=2930
add comment="Guest | Network" interface=bond0 name=vlan2950 vlan-id=2950
/interface list
add comment=defconf name=WAN
add comment=defconf name=LAN
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
/ip pool
add name=vlan2910 ranges=10.29.10.80-10.29.10.200
add name=vlan2920 ranges=10.29.20.80-10.29.20.200
add name=vlan2930 ranges=10.29.30.80-10.29.30.200
add name=vlan2950 ranges=10.29.50.80-10.29.50.200
/ip dhcp-server
add address-pool=vlan2910 interface=vlan2910 name=vlan2910
add address-pool=vlan2920 interface=vlan2920 name=vlan2920
add address-pool=vlan2930 interface=vlan2930 name=vlan2930
add address-pool=vlan2950 interface=vlan2950 name=vlan2950
/interface bridge port
add bridge=bridge comment=defconf interface=ether3
add bridge=bridge comment=defconf interface=ether4
add bridge=bridge comment=defconf interface=ether5
add bridge=bridge comment=defconf interface=ether6
add bridge=bridge comment=defconf interface=ether7
add bridge=bridge comment=defconf interface=ether8
add bridge=bridge comment=defconf interface=sfp-sfpplus1
/ip neighbor discovery-settings
set discover-interface-list=LAN
/interface list member
add comment=untagged interface=bond0 list=LAN
add comment=untagged interface=sfp-sfpplus1 list=WAN
add comment="Core | Network" interface=vlan2910 list=LAN
add comment="Trusted | Network" interface=vlan2920 list=LAN
add comment="Work | Network" interface=vlan2930 list=LAN
add comment="Guest | Network" interface=vlan2950 list=LAN
add comment="Briant | Broadband" interface=vlan911 list=WAN
add comment="WAN | Internet" interface=pppoe0 list=WAN
/ip address
add address=10.29.10.254/24 interface=vlan2910 network=10.29.10.0
add address=10.29.20.254/24 interface=vlan2920 network=10.29.20.0
add address=10.29.30.254/24 interface=vlan2930 network=10.29.30.0
add address=10.29.50.254/24 interface=vlan2950 network=10.29.50.0
add address=10.29.10.1/24 interface=vlan2910 network=10.29.10.0
add address=10.29.20.1/24 interface=vlan2920 network=10.29.20.0
add address=10.29.30.1/24 interface=vlan2930 network=10.29.30.0
add address=10.29.50.1/24 interface=vlan2950 network=10.29.50.0
/ip dhcp-server network
add address=10.29.10.0/24 comment=vlan2910 dns-server=10.29.10.1 gateway=10.29.10.1 netmask=24
add address=10.29.20.0/24 comment=vlan2920 dns-server=10.29.20.1 gateway=10.29.20.1 netmask=24
add address=10.29.30.0/24 comment=vlan2930 dns-server=10.29.30.1 gateway=10.29.30.1 netmask=24
add address=10.29.50.0/24 comment=vlan2950 dns-server=10.29.50.1 gateway=10.29.50.1 netmask=24
/ip dns
set allow-remote-requests=yes servers=10.29.10.35,10.29.10.36
/ip firewall address-list
add address=82.XX.XX.XX comment="Dad's | Home" list=TRUSTED
add address=159.XX.XX.XX comment="Simons | Home" list=TRUSTED
add address=62.XX.XX.XX comment="Steven's | Work" list=TRUSTED
add address=212.XX.XX.XX comment="Trudie's | Home" list=TRUSTED
add address=10.XX.XX.0/24 comment="Core | Network" list=TRUSTED
add address=10.XX.YY.0/24 comment="Trusted | Network" list=TRUSTED
add address=176.XX.XX.XX comment="Hetzner | Dedicated" list=TRUSTED
/ip firewall filter
add action=accept chain=input comment="accept established,related,untracked" connection-state=established,related,untracked
add action=accept chain=input comment="accept to local loopback" dst-address=127.0.0.1
add action=jump chain=input comment="allow icmp" jump-target=icmp
add action=drop chain=input comment="drop invalid" connection-state=invalid
add action=jump chain=input comment="allow access to router" jump-target=router
add action=drop chain=input comment="drop all not coming from LAN" in-interface-list=!LAN log=yes log-prefix=drop_not_LAN
add action=accept chain=forward comment="accept in ipsec policy" ipsec-policy=in,ipsec
add action=accept chain=forward comment="accept out ipsec policy" ipsec-policy=out,ipsec
add action=fasttrack-connection chain=forward comment=fasttrack connection-state=established,related hw-offload=yes
add action=accept chain=forward comment="accept established,related, untracked" connection-state=established,related,untracked
add action=drop chain=forward comment="drop invalid" connection-state=invalid
add action=jump chain=forward comment="allow access to lan" jump-target=lan
add action=drop chain=forward comment="drop all from WAN not DSTNATed" connection-nat-state=!dstnat connection-state=new in-interface-list=WAN
add action=accept chain=icmp comment="0:0 and limit for 5 packets per second" icmp-options=0:0-255 limit=5,5:packet protocol=icmp
add action=accept chain=icmp comment="3:3 and limit for 5 packets per second" icmp-options=3:3 limit=5,5:packet protocol=icmp
add action=accept chain=icmp comment="3:4 and limit for 5 packets per second" icmp-options=3:4 limit=5,5:packet protocol=icmp
add action=accept chain=icmp comment="8:0 and limit for 5 packets per second" icmp-options=8:0-255 limit=5,5:packet protocol=icmp
add action=accept chain=icmp comment="11:0 and limit for 5 packets per second" icmp-options=11:0-255 limit=5,5:packet protocol=icmp
add action=accept chain=router comment="accept SSH to router *trusted*" dst-port=22 log=yes log-prefix=test_log protocol=tcp src-address-list=TRUSTED
add action=accept chain=router comment="accept Winbox to router *trusted*" dst-port=8291 protocol=tcp src-address-list=TRUSTED
add action=accept chain=lan comment="accept access to mgmt01 *trusted*" dst-port=10022 in-interface-list=WAN protocol=tcp src-address-list=TRUSTED
add action=accept chain=router comment="accept udp dns queries from lan" dst-port=53 in-interface-list=LAN protocol=udp
add action=accept chain=router comment="accept tcp dns queries from lan" dst-port=53 in-interface-list=LAN protocol=tcp
add action=accept chain=router comment="accept udp ntp queries from lan" dst-port=123 in-interface-list=LAN protocol=tcp
/ip firewall nat
add action=masquerade chain=srcnat comment="masquerade" ipsec-policy=out,none out-interface-list=WAN
add action=dst-nat chain=dstnat dst-port=10022 in-interface-list=WAN protocol=tcp to-addresses=10.XX.XX.100 to-ports=10022
/ip service
set telnet disabled=yes
set ftp disabled=yes
set www-ssl certificate=XXXX.xyz disabled=no tls-version=only-1.2
set api disabled=yes
set api-ssl certificate=XXXX.xyz tls-version=only-1.2
/ipv6 firewall address-list
add address=::/128 comment="unspecified address" list=bad_ipv6
add address=::1/128 comment=lo list=bad_ipv6
add address=fec0::/10 comment=site-local list=bad_ipv6
add address=::ffff:0.0.0.0/96 comment=ipv4-mapped list=bad_ipv6
add address=::/96 comment="ipv4 compat" list=bad_ipv6
add address=100::/64 comment="discard only " list=bad_ipv6
add address=2001:db8::/32 comment=documentation list=bad_ipv6
add address=2001:10::/28 comment=ORCHID list=bad_ipv6
add address=3ffe::/16 comment=6bone list=bad_ipv6
/ipv6 firewall filter
add action=accept chain=input comment="accept established,related,untracked" connection-state=established,related,untracked
add action=drop chain=input comment="drop invalid" connection-state=invalid
add action=accept chain=input comment="accept ICMPv6" protocol=icmpv6
add action=accept chain=input comment="accept UDP traceroute" port=33434-33534 protocol=udp
add action=accept chain=input comment="accept DHCPv6-Client prefix delegation." dst-port=546 protocol=udp src-address=fe80::/10
add action=accept chain=input comment="accept IKE" dst-port=500,4500 protocol=udp
add action=accept chain=input comment="accept ipsec AH" protocol=ipsec-ah
add action=accept chain=input comment="accept ipsec ESP" protocol=ipsec-esp
add action=accept chain=input comment="accept all that matches ipsec policy" ipsec-policy=in,ipsec
add action=drop chain=input comment="drop everything else not coming from LAN" in-interface-list=!LAN
add action=accept chain=forward comment="accept established,related,untracked" connection-state=established,related,untracked
add action=drop chain=forward comment="drop invalid" connection-state=invalid
add action=drop chain=forward comment="drop packets with bad src ipv6" src-address-list=bad_ipv6
add action=drop chain=forward comment="drop packets with bad dst ipv6" dst-address-list=bad_ipv6
add action=drop chain=forward comment="rfc4890 drop hop-limit=1" hop-limit=equal:1 protocol=icmpv6
add action=accept chain=forward comment="accept ICMPv6" protocol=icmpv6
add action=accept chain=forward comment="accept HIP" protocol=139
add action=accept chain=forward comment="accept IKE" dst-port=500,4500 protocol=udp
add action=accept chain=forward comment="accept ipsec AH" protocol=ipsec-ah
add action=accept chain=forward comment="accept ipsec ESP" protocol=ipsec-esp
add action=accept chain=forward comment="accept all that matches ipsec policy" ipsec-policy=in,ipsec
add action=drop chain=forward comment="drop everything else not coming from LAN" in-interface-list=!LAN
/system clock
set time-zone-autodetect=no time-zone-name=UTC
/system identity
set name=router01
/system ntp client
set enabled=yes
/system ntp server
set enabled=yes
/system ntp client servers
add address=ntp0.linx.net
add address=ntp1.linx.net
add address=ntp2.linx.net
/tool mac-server
set allowed-interface-list=LAN
/tool mac-server mac-winbox
set allowed-interface-list=LAN
I am kinda rusty with MTK as been using UBNT over these past recent years.
Looking forward to your reply.
Simon