Community discussions

MikroTik App
 
eb123456
just joined
Topic Author
Posts: 23
Joined: Sat Jul 24, 2021 6:20 am
Location: California

Bad wifi with hap ac^3

Sat Feb 04, 2023 9:45 pm

I just replaced an ac2 with an ac3 - exact same configuration that I pushed with a script ROS 7.7 - wall mounted, same location.

Image

Image
/interface wireless
set [ find default-name=wlan2 ] band=5ghz-n/ac channel-width=20/40/80mhz-eCee disabled=no frequency=5765 installation=outdoor mode=ap-bridge name=wlan-5g-private \
    security-profile=ABCD ssid=XYZ_ABCD wireless-protocol=802.11
set [ find default-name=wlan1 ] band=2ghz-b/g/n channel-width=20/40mhz-eC country="united states3" disabled=no frequency=2437 installation=outdoor mode=ap-bridge name=\
    wlan-24g-iot security-profile=IOT_SECURE ssid=XYZ_IOT wireless-protocol=802.11
What am I doing wrong?
 
User avatar
bpwl
Forum Guru
Forum Guru
Posts: 2978
Joined: Mon Apr 08, 2019 1:16 am

Re: Bad wifi with hap ac^3

Sat Feb 04, 2023 10:39 pm

Insufficient patience?

MT is known for being slow to get up to speed in wifi. It requires multiple good transmissions before higher speeds are achieved.
MT only takes small steps starting from the lowest interface rate. With the b-rates included that is from 1Mbps. Time connected is still very short here;

And I hope you have verified there is enough free channel room left for 40MHz in 2.4GHz (uncommon)
 
eb123456
just joined
Topic Author
Posts: 23
Joined: Sat Jul 24, 2021 6:20 am
Location: California

Re: Bad wifi with hap ac^3

Sun Feb 05, 2023 4:40 am

Thank you @bpwl - indeed the signal strength got better with time!

I have not verified that here is enough free channel room left for 40MHz in 2.4GHz - how should I do that? Or should I simply reduce the width to 20MHz and see what happens?
 
User avatar
bpwl
Forum Guru
Forum Guru
Posts: 2978
Joined: Mon Apr 08, 2019 1:16 am

Re: Bad wifi with hap ac^3

Sun Feb 05, 2023 4:10 pm

Use the MT to scan (or an APP on tablet or smartphone or testsoftware on a laptop).
Remember 20MHz channel is 4x 5MHz channels wide. Typical choice for 20MHz is channel 1, 6 or 11.

MT: (will disconnect clients on that interface)
in WinBox
Wireless interface use button "Freq usage" ,'Snooper", those are better than just "Scan"
in CLI:(Terminal)
/interface wireless> frequency-monitor
/interface wireless snooper> snoop
then select "f" , "s" or "n"

Windows:
Free programs:
inSSIDer
NetSpot
Wi-Fi Scanner (from LizardSystems)

Android device
Free APP's
Wifi Analyzer (Kevin Yuan) farproc tools, and more similar tools with this name from others
Net Analyzer (Jiri Techet) Network Analyer Lite
 
R1CH
Forum Guru
Forum Guru
Posts: 1098
Joined: Sun Oct 01, 2006 11:44 pm

Re: Bad wifi with hap ac^3

Sun Feb 05, 2023 10:10 pm

40 MHz channel width on 2.4 GHz will certainly lead to bad results. But you need to be specific about what you mean by "Bad wifi", your screenshot does not help.
 
eb123456
just joined
Topic Author
Posts: 23
Joined: Sat Jul 24, 2021 6:20 am
Location: California

Re: Bad wifi with hap ac^3

Mon Feb 06, 2023 5:56 am

my screenshots showed that only half of the devices elected to connect to the ac^3 and that the signal appeared weaker.
But this seemed to have resolved itself overtime.
I have reduced the channel width from 40 MHz to 20 MHz, and switched from channel 6 to channel 1 as it was bit less crowded by my neighbors.
Now I do have similar performance with the new ac^3 as compared to my now retired ac2. it is not working faster/better.
 
User avatar
normis
MikroTik Support
MikroTik Support
Posts: 26287
Joined: Fri May 28, 2004 11:04 am
Location: Riga, Latvia

Re: Bad wifi with hap ac^3

Mon Feb 06, 2023 8:29 am

Side note. If you have neighbors at all, you can't expect much from 2GHz

Who is online

Users browsing this forum: No registered users and 17 guests