CCR got Kernel Panic while installing via Netinstall

RouterOS General
1

Hi,

I gott CCR 16 core and its kernal carshed after upgrade from firmware 6.7 to 6.18 and while trying to reinstall via Netinstall.
i got following error.


RouterBOOT booter 3.18

CCR1016-12G

CPU frequency: 1200 MHz
Memory size: 2048 MiB
NAND size: 512 MiB

Press any key within 2 seconds to enter setup..
trying bootp protocol… OK
Got IP address: 192.168.10.2
resolved mac address 24:B6:FD:3C:13:E6
transfer started … transfer ok, time=3.21s
setting up elf image… OK
jumping to kernel code

Pid: 0, comm: swapper/1, CPU: 1
r0 : 0x0000000000000001 r1 : 0xfffffe0000555d20 r2 : 0x0000000000000000
r3 : 0xffffffffffffffff r4 : 0x0000000000000000 r5 : 0x000001f4ffad0000
r6 : 0x0000000000000001 r7 : 0x0000000000000001 r8 : 0x0000000000000000
0r9 : Cl0ix0en00t 00r0e0qu00es00te00d 00ha0 lt.r1
: 0x000009000000003c r11: 0x0000000000000001
BUG: failure at /flash/rw/build/6.18/kernel/linux6/kernel/stop_machine.c:312/cpu_stop_cpu_callback()!
Kernel panic - not syncing: BUG!

Starting stack dump of tid 1, pid 1 (swapper/0) on cpu 0 at cycle 11234700435
frame 0: 0xfffffff7004efb50 dump_stack+0x0/0x20 (sp 0xfffffe003d26fe20)
frame 1: 0xfffffff7004e8dd0 panic+0x168/0x388 (sp 0xfffffe003d26fe20)
frame 2: 0xfffffff70052c1d8 cpu_stop_cpu_callback+0xe0/0x268 (sp 0xfffffe003d26fec8)
frame 3: 0xfffffff700085948 notifier_call_chain+0x80/0xf8 (sp 0xfffffe003d26fef0)
frame 4: 0xfffffff7004e90b8 __cpu_notify+0x38/0x80 (sp 0xfffffe003d26ff28)
frame 5: 0xfffffff70052a7a0 cpu_up+0x128/0x278 (sp 0xfffffe003d26ff38)
frame 6: 0xfffffff700511090 smp_init+0x190/0x198 (sp 0xfffffe003d26ff88)
frame 7: 0xfffffff700500fc8 kernel_init+0xe0/0x208 (sp 0xfffffe003d26ffc8)
frame 8: 0xfffffff700029ac8 start_kernel_thread+0x18/0x20 (sp 0xfffffe003d26ffe8)
Stack dump complete

Please help!!!

2

you use netisntall 6.18 and routeros-tile-6.18.npk?

try to reset bios on serial console.

on alternative you can try this…
http://www.mikrotik.com/download/share/routeros-tile-6latest.npk

DO NOT FORMAT NAND ON BIOS OR YOU LOSE YOUR LICENCE!!!

3

Thanx for your reply, Yes i did the same with same version of netinstall but netintall won’t detect the CCR over there.

4

Try with netinstall 6.17 (change number on official 6.18 download link) and try to install 6.18

5

Hi,

I try to do bu version 6.7 then it shows this
RouterBOOT booter 3.18

CCR1016-12G

CPU frequency: 1200 MHz
Memory size: 2048 MiB
NAND size: 512 MiB

Press any key within 2 seconds to enter setup..

loading kernel from nand… kernel not found or data is corrupted
trying bootp protocol… OK
Got IP address: 192.168.1.2
resolved mac address B8:AC:6F:78:27:EA
transfer started … transfer ok, time=1.80s
setting up elf image… OK
jumping to kernel code
Machine shutting down before console output is fully initialized.
You may wish to reboot and add the option ‘earlyprintk’ to your
boot command line to see any diagnostic early console output.

What;s the solution.

Regards