Metarouter images

[RobertoMenesesB]

Dear Nathan,

Mikrotik have experience but am new to MetaRouter, Might me some manual or procedure to virtualize asterisk on mikrotik, I’m studying to propose as a topic for my college thesis, Greetings from Ecuador

[janisk]

for this - you have to have your own built OpenWRT and then you can make binaries of your liking following OpenWRT documentation on how to create binaries for flavor of OpenWRT you have built. (Package building)

[iqt]

@mattijs

Not sure why this wasn’t done before or what I’ve broken in the process;

I’ve taken the latest OpenWRT Backfire snapshot (r33081). I then applied the metarouter patches to the longterm 2.6.32 kernel which is 2.6.32.61 at the time of writing. This is the 2.6.x with the latest projected EOL, somewhere Mid-2014 probably. I build a rootfs, it boots, but that’s as far as I’ve tested it.

I’m a bit unsure how to proceed now, do I try and get ‘Attitude Adjustment’ to run a 2.6.32 kernel? Or do I try to get the metarouter patches to work for the 3.x kernel?

Mattijs
oh, here’s the link to the rootfs for now: https://dl.dropboxusercontent.com/u/3764154/openwrt-metarouter/r33081_linux-2.6.32.61/openwrt_backfire_r33081_mr-mips-rootfs.tar.gz

@mattijs: Could you provide your patches for backfire r33081 and kernel 2.6.32.61 please. I downloaded the source from openwrt and adopted the patches. Compilation is ok but I can’t start the image.

Thanks! Dirk

Linux version 2.6.32.61 (dirk@obelix) (gcc version 4.3.3 (GCC) ) #1 Sun Dec 22 11:
56:37 CET 2013
CPU revision is: 0001800a (MIPS 4Kc)
Determined physical RAM map:
User-defined physical RAM map:
 memory: 01800000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00001800
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00001800
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 6096
Kernel command line: init=/etc/preinit console=hvc0 board=vm mem=24M 
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Memory: 20816k/24576k available (1952k kernel code, 3760k reserved, 295k data, 128
k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
console [hvc0] enabled
Calibrating delay loop... 418.81 BogoMIPS (lpj=837632)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
Unhandled kernel unaligned access[#1]:
Cpu 0
$ 0   : 00000000 0000006b 00000000 00000000
$ 4   : c01107a0 a1700000 00000000 c0c68d08
$ 8   : 10008201 1000001e 00000000 c0c68cb0
$12   : 00000000 c032ba98 c03276bc 00000000
$16   : 8c430000 c0c17de8 c0360000 00000000
$20   : c033aaf0 00000000 00000000 00000000
$24   : c0c68d08 c0119ac0                  
$28   : c0c16000 c0c17dc0 00000000 c0101460
Hi    : 00000000
Lo    : 00000000
epc   : c01107b8 0xc01107b8
    Not tainted
ra    : c0101460 0xc0101460
Status: 10008203    KERNEL EXL IE 
Cause : 00000010
BadVA : a1700000
PrId  : 0001800a (MIPS 4Kc)
Modules linked in:
Process swapper (pid: 1, threadinfo=c0c16000, task=c0c15938, tls=00000000)
Stack : c032bb48 c01429a4 00000082 00000000 c0c04500 c03521c8 c03522e0 c0360000
        00000000 c0101460 c0328bc0 c0142ec4 c0c13e10 00000000 c0c6b880 00000000
        00000000 0000006b a1700000 a0000000 a1700000 00004000 01703fff c0c68d08
        c032769c c02fa08c 00000000 c0c68cb0 00000000 c032ba98 c03276bc 00000000
        c03521c8 c03522e0 c0360000 00000000 c033aaf0 00000000 00000000 00000000
        ...
Call Trace:[<c01429a4>] 0xc01429a4
[<c0101460>] 0xc0101460
[<c0142ec4>] 0xc0142ec4
[<c033aaf0>] 0xc033aaf0
[<c0119ac0>] 0xc0119ac0
[<c012a484>] 0xc012a484
[<c033ab20>] 0xc033ab20
[<c033ab2c>] 0xc033ab2c
[<c033aae0>] 0xc033aae0
[<c0109610>] 0xc0109610
[<c01de6fc>] 0xc01de6fc
[<c0155314>] 0xc0155314
[<c0334348>] 0xc0334348
[<c01b4e50>] 0xc01b4e50
[<c010af94>] 0xc010af94
[<c0334264>] 0xc0334264
[<c010af84>] 0xc010af84


Code: 00431024  14400063  00000000 <88b20000> 98b20003  24020000  14400051  000000
00  08044203 
Disabling lock debugging due to kernel taint
Kernel panic - not syncing: Attempted to kill init!

[/size]

[liquidcz]

New build Kamikaze 18961 - image, packages tree, config
Default root password: master
eth0 is preconfigured to use DHCP
New requested packages: rsync, stunnel, quagga, srelay
MIPS:
http://openwrt.wk.cz/kamikaze/openwrt-mr-mips-rootfs-18961.tar.gz
CONFIG MIPS:
http://openwrt.wk.cz/kamikaze/config-kamikaze-mips-18961-20131227
PACKAGES:
http://openwrt.wk.cz/kamikaze/packages/mr-mips/

PPC:
http://openwrt.wk.cz/kamikaze/openwrt-mr-ppc-rootfs-18961.tar.gz
CONFIG PPC:
http://openwrt.wk.cz/kamikaze/config-kamikaze-ppc-18961-20131227
PACKAGES:
http://openwrt.wk.cz/kamikaze/packages/mr-ppc/

[LeoCombes]

@liquidcz

New build Kamikaze 18961 - image, packages tree, config
Default root password: master
eth0 is preconfigured to use DHCP
New requested packages: rsync, stunnel, quagga, srelay

Excellent news liquidcz!!!
Any posibility of include zabbix_proxy 2.0 in repository?
I tried to compile without success, my compiler skills are not very good.

Thanks for your effort!

[otgooneo]

@liquidcz

New build Kamikaze 18961 - image, packages tree, config
Default root password: master
eth0 is preconfigured to use DHCP
New requested packages: rsync, stunnel, quagga, srelay

Thanks liquidcz. Do you have any news on stability?

[bysard]

Thank you liquidcz. I have no problems running this image but I can’t change the IP address from DHCP to static. When I click save, I see new values, but when I reboot the router it goes back to DHCP.

[liquidcz]

@LeoCombes

@liquidcz

New build Kamikaze 18961 - image, packages tree, config
Default root password: master
eth0 is preconfigured to use DHCP
New requested packages: rsync, stunnel, quagga, srelay

Excellent news liquidcz!!!
Any posibility of include zabbix_proxy 2.0 in repository?
I tried to compile without success, my compiler skills are not very good.

Thanks for your effort!

I’m afraid that I can only add zabbix 1.6, which is officially in Kamikaze feeds.

[liquidcz]

@otgooneo

@liquidcz

New build Kamikaze 18961 - image, packages tree, config
Default root password: master
eth0 is preconfigured to use DHCP
New requested packages: rsync, stunnel, quagga, srelay

Thanks liquidcz. Do you have any news on stability?

Stability? Did you mean those problems with occasional reboot?

[liquidcz]

@bysard

Thank you liquidcz. I have no problems running this image but I can’t change the IP address from DHCP to static. When I click save, I see new values, but when I reboot the router it goes back to DHCP.

If you are using web administration, after clicking “Save Changes”, you still have to click on the “Applay Changes” at the bottom of the page.

[bysard]

@liquidcz

@bysard

Thank you liquidcz. I have no problems running this image but I can’t change the IP address from DHCP to static. When I click save, I see new values, but when I reboot the router it goes back to DHCP.

If you are using web administration, after clicking “Save Changes”, you still have to click on the “Applay Changes” at the bottom of the page.

ty

[LeoCombes]

@liquidcz

@LeoCombes

@liquidcz

New build Kamikaze 18961 - image, packages tree, config
Default root password: master
eth0 is preconfigured to use DHCP
New requested packages: rsync, stunnel, quagga, srelay

Excellent news liquidcz!!!
Any posibility of include zabbix_proxy 2.0 in repository?
I tried to compile without success, my compiler skills are not very good.

Thanks for your effort!

I’m afraid that I can only add zabbix 1.6, which is officially in Kamikaze feeds.

Surely, the same is going to happend with other packages, soon. They will be outdated.
Can I run a latest version of the openWRT (Attitude Adjustment) in the routerboard? Or is not possible or technically complicated?

Thanks.

[blazej44800]

Hello.

liquidcz: can you add packages: minidlna, kmod-usb-uhci, kmod-usb-ohci, kmod-usb2, kmod-usb-printer, p910nd

Thanks a lot (vďaka )

[Vitaly]

Hello, please add print server (printer support) to metarouter. I tried install cups, but it not works.
Thanks!

[bysard]

@Vitaly

Hello, please add print server (printer support) to metarouter. I tried install cups, but it not works.
Thanks!

How do you intend to push USB to metarouter?

[Vitaly]

@bysard

How do you intend to push USB to metarouter?

Hi. I am not developer of this system and don’t know.
But I see two ways:

1. Native support for RouterOs
2. Forward /dev to metarouter, create image with printer support(with cups or something). If they made this for network devices, maybe this is not big deal for usb. Maybe usb not work in metarouter for security reasons.

**Topic with request http://forum.mikrotik.com/t/add-print-server-printer-support/74629/1

[bysard]

It was a retorical question and the answer is no, you can’t. You can only share ether devices with metarouter.

[liquidcz]

I just create new repositories for Backfire 10.03.1 build 29592 + ALL packages

OpenWrt milestone info: https://dev.openwrt.org/milestone/Backfire%2010.03.1

Modifications:

• Mikrotik MetaRouter Patch 1.2
• changed root password to: master
• changed eth0 to DHCP
• changed opkg source to my repositories

MIPS:
http://openwrt.wk.cz/backfire/mr-mips/openwrt-mr-mips-rootfs.tar.gz
CONFIG MIPS:
http://openwrt.wk.cz/backfire/mr-mips/config-mips-backfire-29592
PACKAGES:
http://openwrt.wk.cz/backfire/mr-mips/packages/

PPC:
http://openwrt.wk.cz/backfire/mr-ppc/openwrt-mr-ppc-rootfs.tar.gz
CONFIG PPC:
http://openwrt.wk.cz/backfire/mr-ppc/config-ppc-backfire-29592
PACKAGES:
http://openwrt.wk.cz/backfire/mr-ppc/packages/

Enjoy!

[jarda]

Does it work in rb2011 with ros 6.9 or 6.10?

Sent from Android by Tapatalk.

[payday]

@jarda

Does it work in rb2011 with ros 6.9 or 6.10?

Works, very well!

Thank You, liquidcz!