v6.34 [current] is released!

[Toigoweb]

No Ip → Cloud in hap Lite with Winbox 3.1
Schermata 2016-01-30 alle 20.38.57.png

[jspool]

L2TP / IPsec VPN from Android is not working since I upgraded to 6.34 Reverted back to 6.33.5 and it works again. Mikrotik to Mikrotik works providing they are all 6.34 But log doesnt even give errors on 6.34 with Android VPN connection attempts.

[pzimin]

@jspool

L2TP / IPsec VPN from Android is not working since I upgraded to 6.34 Reverted back to 6.33.5 and it works again. Mikrotik to Mikrotik works providing they are all 6.34 But log doesnt even give errors on 6.34 with Android VPN connection attempts.

I have got just the same issue. IPSEC between Mikrotiks only work if they all have 6.34 version. Android cannot connect via L2TP+IPSEC after RouterOS upgrade.

[pe1chl]

@pzimin

@jspool

L2TP / IPsec VPN from Android is not working since I upgraded to 6.34 Reverted back to 6.33.5 and it works again. Mikrotik to Mikrotik works providing they are all 6.34 But log doesnt even give errors on 6.34 with Android VPN connection attempts.

I have got just the same issue. IPSEC between Mikrotiks only work if they all have 6.34 version. Android cannot connect via L2TP+IPSEC after RouterOS upgrade.

Please read the release notes!

*) ipsec - fix phase2 hmac-sha-256-128 truncation len from 96 to 128
This will break compatibility with all previous versions and any other
currently compatible software using sha256 hmac for phase2;

So you must not use sha256

[abis]

@Toigoweb

No Ip → Cloud in hap Lite with Winbox 3.1

And same problem as RB3011, no Switch menu too.

[Petzl]

*) crs212 - fix 1Gbps ether1 linking problem;

i did had some packetloss on port 1 of a CRS212, hope this can be solved with this fix.
the stange thing was that i had this problem also on a CRS109.

[Kevo]

We also are seeing traffic graph issues with the release. rc41 was fine. After upgrade to the release the graph shows lower values than the interfaces do.The only lines in the graph that look to be proper size are ones that were drawn while refreshing the graph page.

So the first two graph lines at 9am local time show traffic to be around 1Gbps which is correct. After leaving and coming back 10 minutes later I refresh and the very next line shows less than 200Mbps.

[Kevo]

Also, voltage shows 0.0 under system heath now. CCR1072.

[kamillo]

After upgrade on CRS125, vlans trunk disappeared from bonded interface.

Easily fixed by adding vlans to the interface but that should not happened.

[OrCAD]

Hello,
link to download all? torrent?

thank you

[Beone]

@avantwireless

@Cha0s

Can you be more specific? What exactly isn’t working?

I’ve upgraded 3-4 devices to 6.34 so far and I haven’t got any issues with SNMP (or anything else for that matter) using Cacti, Observium, Dude and custom scripts.

We are seeing the numbers on the interfaces way lower than the actual interfaces are showing…
6.34 was the section between the two vertical bars… Stats drop off to 1/10? normal

We also opened ticket [Ticket#2016013166000402] as we have exactly the same thing, SNMP is reporting about 1/10 of real actual traffic passing through.

[Benik3]

I wasn’t here for a long time, but about the Dude, it’s being improved?
It’s about 2 years back what I tried it…

Thanks

EDIT: Well I see now that server is only supported on Tile or x86 Mikrotik

[paoloaga]

@Kevo

We also are seeing traffic graph issues with the release. rc41 was fine. After upgrade to the release the graph shows lower values than the interfaces do.The only lines in the graph that look to be proper size are ones that were drawn while refreshing the graph page.

So the first two graph lines at 9am local time show traffic to be around 1Gbps which is correct. After leaving and coming back 10 minutes later I refresh and the very next line shows less than 200Mbps.

I can confirm that on my routers the bandwidth usage displayed in graphs is much lower than the real.

[scampbell]

@strods

About ARP entries - they are completely normal. They have been there forever. Incomplete entries simply were no shown. Now we just do not hide them any more.

Just a thought - how hard would it be to add a tick box for “show-incomplete” in /ip arp ? This may make it easier for some users to understand ?

[strods]

timoid, Red0ktober - We have tested upgrade on these devices and it works. It must be configuration related. Please contact support.
Those who complain about missing “Switch” menu in Winbox - upgrade Winbox to 3.1 and you will see this menu.
Everyone - please report to support@mikrotik.com with description of your problem and screen shots. Forum is for users. If you want to have resolution to your issues, then you should report to support.

[felted67]

Hi everyone,

well, congratulations for the Dude project - working fine…

But, also some problems here with 6.34-update :

Main-Router 2011UiAS-2HnD and two RB952Ui-5ac2nD with CAPsMAN-configuration.
I recognize that two mobile phones are drained when connected to AP/CAPsMAN.

Is there something wrong with Powermanagement (edited: not WMM) or similar function ?
After 8-10 h both batteries are drained until 5% remaining, before update running time was about
5 days… (both values with similar using situations).

Installed is wireless-cm2 on all devices..
If you need more specific informations about my configuration, please feel free to contact me.

Thank you very much…

Regards

Detlef

[zervan]

There is something wrong in 6.33.6 and 6.34 relating secondary column sorting in WinBox, both 3.0 and 3.1. See the screenshot from 6.33.5 and previous versions - I use the sorting where ascending Address is primary and descending Expires secondary column.
dhcp-server-leases.png
I can not set that in newer RouterOS. (I have just tried my home RB2011UiAS, nothing else)

[felted67]

@zervan

There is something wrong in 6.33.6 and 6.34 relating secondary column sorting in WinBox, both 3.0 and 3.1. See the screenshot from 6.33.5 and previous versions - I use the sorting where ascending Address is primary and descending Expires secondary column.
I can not set that in newer RouterOS. (I have just tried my home RB2011UiAS, nothing else)

Well, because of many static entries in my dhcp-server-leases-list, I thought dynamic entriess are gone.
They are only sorted by ip-address, as my dhcp-pool is at the end of the ip-block (>x.x.x.230),
I can see them, but not at first position as before…

Perhaps a new feature ?

Then there is a lack of sorting by “dynamicly” entries.

Regards…Detlef

[rpingar]

@avantwireless

@Cha0s

Can you be more specific? What exactly isn’t working?

I’ve upgraded 3-4 devices to 6.34 so far and I haven’t got any issues with SNMP (or anything else for that matter) using Cacti, Observium, Dude and custom scripts.

We are seeing the numbers on the interfaces way lower than the actual interfaces are showing…
6.34 was the section between the two vertical bars… Stats drop off to 1/10? normal

I have the same identical problem and i opened a ticket this morning.

regards
Ros

[strods]

What is the actual problem with sorting? We fixed Winbox and DHCP leases. Big part of information was not shown for static entries. Now you can see it. Please send to support@mikrotik.com screen shots where we could see correct and incorrect behaviour.