My hAP ac2 that I use as ap after the upgrade from 7.1rc7 now fowards every single vlan traffic to the wireless interfaces
You will have to netinstall it. Upgrading from separate packages (not the bundled package) to v7 (or to v6.xx bundled package, for that matter) does not work on small devices!
will this release can solved MikroTik support #[SUP-66821]: RB5009UG+S+IN randomly reboot when 100+ pppoe user is connected ?
How did you configure that? There are of course several ways to do it. I think configuring the vlan in the wireless interface settings is being deprecated.
I use a vlan-filtering bridge with the wifi interfaces as untagged ports on the VLANs and the appropriate PVID and the ports. It appears to work.
I use the hAP ac2 as a switch as well, but, I cannot use vlan-filtering because my IPTV traffic will not work properly (it pass through it), so I’ve configured each wlan interface with
vlan-id=110 vlan-mode=use-tag
It was working perfectly before the last upgrade. after the upgrade, now I see all vlans being send in the “air” even the fat IPTV one that made some devices really confused…
Interesting, after upgrade to 7.1, all the channels say latest are 7.1. No more 6.49.1
Doest this testing version fix the DHCP-PD over PPPoE VLAN interface?
!) support for VRRP grouping and connection tracking data synchronization between nodes;
Can anyone shape a example (may be config) that features?
!) support for Virtual eXtensible Local Area Network (VXLAN);
How can it be used ? Does Rosv7 support EVPN based on VXLAN?
No, RB5009 fails. CCR2004 works.
A lot of the V7 stuff is in the the newer help.mikrotik.com site, than the now older wiki, including VRRP:
https://help.mikrotik.com/docs/display/ROS/VRRP
The “additional footnotes” for VRRP support in V7 is here:
http://forum.mikrotik.com/t/vrrp-connection-tracking-and-preemption-mode/148750/1
Summary is a one-way sync from master to backup – and you can no longer use preemption mode if you use. Not tested the connection tracking part, but VRRP has been stable for us in V7 for some time.
7.1 Installed(updated) ok on x86(test) and on RBcAPGi-5acD2nD.
MACSec/802.11AE still not working…
Hi
thanks for the hint. As the system is not easy to reach i will prepare a replacement hAP Lite and replace it once i go there.
Im wondering why the upgrade is then offered ? It should not be offered at all then.
Reason why i have not the full package is that i had upgrade issues here and there and by limiting the amount of packages i had continues succcess. Lets see how this goes with version 7.x if we only have a full package.
2011UiAS-2HnD here, all ports 6-10 are now only negotiate at 100mbit.
Those ports are 100Mbps by design, they always were 100Mbps.
Right you are, strange … someone must be playing tricks on me and swapped some cables around 
This is why you should before upgrade.
- Read forum carefully.
- Install on a test device equal to the remote device.
- Wait some weeks after new software is released to make sure there are no mayor hicups.
- Read title of this thread
v7.1 [> testing> ] is released!
Port 1-5 are gigabit
Port 6-10 are 100 MB
See picture:
You have to download the package yourself and upload it to your HAP and then reboot.
Or perhaps problem in how ROS configures RTL8367 switch chip? Handling of switch chip has been vastly improved in v7 (previously that switch chip was next to useless as a piece of hardware), but it’s likely there’s room for improvement.
Yep, still a problem on the RB5009