v7.13.5 [stable] is released!

[Shadeofspirit]

Crs326 - bonding stop working after update to 7.13
Disabling/enabling bonding interface, recreation doesn’t help.
Traffic is just stop going after update. (Synology nas is in the other end)

[urknall]

I have an issue with 7.13 that 7.12.1 didn’t have (nor before) - I have a bunch of 1gb SFP’s in a CRS328-4C-20S-4S+ switch. None of them will link up auto negotiation at full duplex (they are all fiber). I can hard code both sides of a link and it works full duplex, but with auto negotiation duplex is never picked up and you end up with hundreds of “sfpxx excessive or late collision, link duplex match?” errors and most paths not even passing traffic. Downgrade to 7.12 and it auto negotiates correctly. My 10GB SFP+'s are auto negotiating, only 1GB SFP modules are failing to.

I also have problems with a Mikrotik S+RJ10 Module and CRS326-24G-2S+RM:

it says link ok, but i cannot connect to the server that is connected via ethernet 10G. Had to netinstall 7.12.1 to get the connection working again…

[ghassan73]

Thanks, however, HAP AC3 (RBD53iG-5HacD2HnD) central led now flashing red. I believe this central LED is related to lte / wps?
Up until version 7.12.1 it was solid blue.
Please advise.

[Matta]

Upgraded two LHG XL52 ac (PtP setup), settings were intact, no issue with signal (-42), devices register themselves on one another (both 2GHz and 5GHz), but can’t see other LHG via Winbox.
Any clues ?

EDIT: on 7.12.1 was working perfectly.

[JohnTRIVOLTA]

Upgraded two LHG XL52 ac (PtP setup), settings were intact, no issue with signal (-42), devices register themselves on one another (both 2GHz and 5GHz), but can’t see other LHG via Winbox.
Any clues ?

EDIT: on 7.12.1 was working perfectly.

Are you using the new wifi package? If yes, it does not support station bridge mode yet with old devices/old driver! I use bridge and eoip over wifi link for extending the L2 segment

[mike7]

CCR1016 after updating to 7.13 not show lte interface anymore.
But in USB list it showing.

wireless already installed

At 7.12 all ok.

The same on hAP ac^3. Sometime after reboot I’ve got lte interface and internet access but can’t access web interface of the modem in hilink mode.

[mike7]

After upgrading my hAP ax^3 to ROS 7.13 everything works fine, but the front WPS button which previously was solid blue, now blinks in red.
Created a ticket (SUP-137799).

Do you have usb modem attached? I’ve got red blinks right after modem connection.

[dcavni]

Upgraded two LHG XL52 ac (PtP setup), settings were intact, no issue with signal (-42), devices register themselves on one another (both 2GHz and 5GHz), but can’t see other LHG via Winbox.
Any clues ?

EDIT: on 7.12.1 was working perfectly.

Are you using the new wifi package? If yes, it does not support station bridge mode yet with old devices/old driver! I use bridge and eoip over wifi link for extending the L2 segment

There is station bridge mode in new drivers. Tried it just yesterday on LHG52.

[holvoetn]

Yup, already in beta versions. Tested it as well.

[krafg]

Updated all my devices without issues.

Regards.

[Matta]

@holvoetn

Yup, already in beta versions. Tested it as well.

I know it’s a guessing game, but I cannot find what seems to be the problem. I have 2 pairs of PtP link, similar setup (apart for SSID names etc). Both pairs were on 6.49.11. I’ve upgraded both pairs to 7.12.1 and both were working. Now I upgraded one pair to 7.13 and have above issues. I checked all settings but cannot find the cause.

[holvoetn]

Start separate thread with export of config.

[eguun]

This AM i upgraded my CCR1009 from version 7.12.1 to version 7.13 now getting the following error when running a script

Download from https://view.sentinel.turris.cz/greylist-data/greylist-latest.csv to RAM FAILED: Fetch failed with status 206

The same script was working fine under 7.12.1 and earlier versions

Same problem with other scripts:

error ex.
Download from http://::ffff:192.168.8.1/api/webserver/SesTokInfo (::ffff:192.168.8.1) to RAM FAILED: Host is unreachable

versions prior to 7.12.1 there were no problems

+1, report the same error:

• fetch with ipv4 url are automatically “translated” into ipv6 by being prefixed with “::ffff:”
• This results in either host unreachable or data content = null

Had to roll back to 7.12.1

[dcavni]

@holvoetn

Yup, already in beta versions. Tested it as well.

I know it’s a guessing game, but I cannot find what seems to be the problem. I have 2 pairs of PtP link, similar setup (apart for SSID names etc). Both pairs were on 6.49.11. I’ve upgraded both pairs to 7.12.1 and both were working. Now I upgraded one pair to 7.13 and have above issues. I checked all settings but cannot find the cause.

When i upgraded LHG52 to 7.13 first in didn’t even see wireless intefaces even if wireless package was installed (checked). Probably because there was also Zerotier package on it and something went wrong with the instalation (to little space for all those packages).
I just deleted it and installed qcom ac package and everything seems fine.

[cyrq]

After upgrading my hAP ax^3 to ROS 7.13 everything works fine, but the front WPS button which previously was solid blue, now blinks in red.
Created a ticket (SUP-137799).

Do you have usb modem attached? I’ve got red blinks right after modem connection.

Yes!
Just tested this and your’re right. After connecting the USB modem the LED starts flashing red.
Unplugging it doesn’t change it’s behavior. You need to reboot the whole router with the modem unplugged. Plugging it back makes the LED starts blinking red again.
EDIT: disabling the dynamic lte1 interface also restores the LED back to normal (static blue).

[kravemir]

Wifi experience was great as soon as I figured out the security connect-priority=0/1 option and managed to work around the VLAN limitation.

Why is that needed? In my WifiWave2/WiFi CAPsMAN setup I don’t use this, and devices connect and roam successfully.

Now I’m just hoping that VLAN tagging will find its way back into wifi-qcom-ac driver to restore the flexibility it provides.

Me too. It would make CAP more controlled - better provisioned without a need to manually set bridge ports and VLANs for wifi interfaces on each CAP.

[mike7]

Do you have usb modem attached? I’ve got red blinks right after modem connection.

Yes!
Just tested this and your’re right. After connecting the USB modem the LED starts flashing red.
Unplugging it doesn’t change it’s behavior. You need to reboot the whole router with the modem unplugged. Plugging it back makes the LED starts blinking red again.

My modem is useless with 7.13 (
lte interface just disappeared )

[diamuxin]

+1, report the same error:

• fetch with ipv4 url are automatically "translated" into ipv6 by being prefixed with "::ffff:"
• This results in either host unreachable or data content = null

Had to roll back to 7.12.1

Indeed that is the problem, you have explained it better than me
Let's see what solution they give us.

TESTs:

# Imput CLI:
{
:local urlSesTokInfo "http://192.168.8.1/api/webserver/SesTokInfo"
:put ([/tool fetch $urlSesTokInfo output=user as-value]->"data")
}

# Log message v7.13:
Download from http://::ffff:192.168.8.1/api/webserver/SesTokInfo (::ffff:192.168.8.1) to RAM FINISHED

# Log message v7.12.1:
No message (ok)

Why do more messages appear in the log like fetch, stp, debug, etc?

[whatever]

Why is that needed? In my WifiWave2/WiFi CAPsMAN setup I don’t use this, and devices connect and roam successfully.

At least with FT disabled, the default connect-priority setting delays roaming to a new AP until a client has disconnected from its previous AP. With my Android phone this caused several seconds of delay when roaming.

Setting connect-priority=0/1 ensures connections to a new AP are immediately accepted and the old AP connection is dropped automatically. When using PSK authentication, this allows seamless roaming even without FT.

[ppsascha]

Hi all!

I have the same problem with script on CHR after upgrade

Download from https://antifilter.download/list/ip.lst to <nothing> FINISHED
Download from https://antifilter.download/list/ip.lst to RAM FAILED: Fetch failed with status 206

What can i do with this?