RouterOS version 7.20beta has been released on the “v7 testing” channel!
Before an upgrade:
- Remember to make backup/export files before an upgrade and save them on another storage device;
- Make sure the device will not lose power during upgrade process;
- Device has enough free storage space for all RouterOS packages to be downloaded.
What’s new in 7.20beta5 (2025-Jul-03 17:21):
*) bfd - fixed socket leak (additional fixes);
*) bgp - automatically create output.network blackhole routes;
*) bgp - do not show router-id error when instance is not active (introduced in v7.20beta2);
*) bgp - refresh WinBox when BGP session is created/deleted;
*) bgp - support for Advertising IPv4 Network Layer Reachability Information (NLRI) with an IPv6 Next Hop;
*) bridge - added dynamic tagged entry named "switch-cpu" in scenarios where the same VLAN spans multiple switch chips or is used on both HW and SW ports (additional fixes);
*) bridge - allow IPv6 FastPath when dhcp-snooping is enabled;
*) dhcp-server - improved logging when dual-stack is enabled but fails to acquire client MAC from DUID;
*) disk - disallow adding SMB share or user with empty name;
*) ethernet - improved ethernet stability when handling invalid packets on Alpine CPUs;
*) ethernet - improved performance for hEX Refresh and hEX S (2025);
*) filesystem - improved calculation of free space on NAND flash (fixes potential "disk is too small" issue);
*) ipsec - fixed responder on key exchange compute failure (introduced in v7.19);
*) lte - AT modems, fixed typos in commands sent to modem when APN with authentication is used (AT+CGAUTH; AT$QCPDPP);
*) lte - do not reconfigure modem if deactive eSIM profile is deleted;
*) lte - exempt eSIM provision from global CRL certificate settings;
*) lte - R11e-LTE and R11e-LTE6, fixed possible crash on device unexpected removal or during RouterOS shutdown;
*) radius - fixed RADIUS client section becoming unresponsive when RadSec is configured, but server is not responding;
*) radius - fixed wrong RadSec port number in logs;
*) radius - properly verify certificate when RadSec is used;
*) route - fixed issue when route table is installed to kernel without fib setting;
*) route - removed fib-reinstall;
*) sfp - fixed low power mode pins on CRS326-4C+20G+2Q+ for optical QSFP modules;
*) supout - added IPv6 NAT section;
*) switch - fixed ACL rules with "redirect-to-cpu" (introduced in v7.20beta2);
*) switch - fixed bonding issues after switch reset (introduced in v7.18);
*) switch - fixed port blocking with spanning tree on EN7523 switch (introduced in v7.19);
*) swos - changed firmware file location (URL) for software update checks;
*) system - improved system stability when processing large amount of traffic;
*) system - improved system stability when using FastTrack;
*) system - reduced RouterOS ARM package size;
*) vrrp - added "connection-tracking-port" and "connection-tracking-mode" settings for "sync-connection-tracking" (additional fixes);
*) wifi - avoid picking 5GHz channels by default which are unlikely to be supported by clients, can be overridden with channel.deprioritize-unii-3-4;
*) winbox - added missing properties to "Container" menu and improved field ordering;
*) winbox - fixed missing warning under "Routing/BGP/Instances" menu;
*) winbox - show/hide corresponding fields when switching RADIUS client mode between RadSec and UDP;
What’s new in 7.20beta4 (2025-Jun-13 11:38):
*) bfd - fixed socket leak;
*) bgp - fixed origin cleanup for mpls-vpn (introduced in v7.20beta2);
*) bgp - fixed warning when instance is not active (introduced in v7.20beta2);
*) bgp - fixed withdraw when input.accept-nlri is non-existent;
*) bgp - migrate correctly router-id and ASN to instance (introduced in v7.20beta2);
*) bridge - added dynamic tagged entry named "switch-cpu" in scenarios where the same VLAN spans multiple switch chips or is used on both HW and SW ports (additional fixes);
*) btest - properly close unsuccessful TCP test sockets;
*) certificate - added "Amazon Root CA 1" to built-in root certificate authorities store;
*) console - added prompt to /disk/format command;
*) console - fixed /file/find not recursive by default (introduced in v7.20beta2);
*) console - fixed /file/read command (introduced in v7.20beta2);
*) console - improved visuals for hexadecimal strings;
*) console - prioritize directory specific parameters and hide rarely used ones in print autocomplete (additional fixes);
*) container - added repull command;
*) container - can use KVM (x86 and arm64) in container QEMU for faster virtualization;
*) container - fixed QEMU VM to host bridge;
*) container - stability improvements (additional fixes);
*) dhcp-client - show warning if DHCP client is configured on dot1x server port;
*) dhcpv4-client - allow specifying DSCP of outgoing packets;
*) dhcpv4-client - show "custom-hostname-suffix" and "custom-source-mac-address" properties if set;
*) dhcpv4-server - added "add dns" step to setup wizard;
*) discovery - improved LLDP Power via MDI TLV with 802.3bt specific field support;
*) discovery - report router as "CAPsMAN" on MNDP under "running" parameter;
*) disk - show error when file based block-device uses a mountpoint to be unmounted;
*) dns - fixed memory leak when static CNAME record was matched;
*) evpn - fixed auto ID setting (introduced in v7.20beta2);
*) evpn - fixed enable/disable handling (introduced in v7.20beta2);
*) evpn - fixed instance handling (introduced in v7.20beta2);
*) evpn - fixed MACIP address decode (introduced in v7.20beta2);
*) evpn - fixed missing RD (introduced in v7.20beta2);
*) evpn - fixed route print query by EVPN AFI (introduced in v7.20beta2);
*) file - fixed console completion not showing all files (introduced in v7.20beta2);
*) file - fixed duplicate in WinBox Files menu when sharing a file in a folder (introduced in v7.20beta2);
*) iot - LoRa netid filters now can be configured as a "range";
*) iot - LoRa stability improvement (additional fixes);
*) iot - LR8G/9G firmware update (additional fixes);
*) ip-service - fixed "print count-only interval" when dynamic entries are added (introduced in v7.19);
*) ip-service - fixed setting services by name (introduced in v7.19);
*) ip-service - show service name "nfs" for port 2049;
*) ipsec - move raw RSA keys to /ip/ipsec/key/rsa;
*) ipv6 - fixed "auto-link-local" feature on WireGuard interface;
*) isis - added passive parameter for interface templates;
*) l2tp-ether - fixed interface creation/removal process;
*) lte - added "remove-sent-sms-after-send" option to automatically delete sent SMS messages;
*) lte - added modem-init string response to system log;
*) lte - added show-capabilities eSIM presence detection for MBIM modems;
*) lte - added support for R11e-LTE6 v039 firmware release;
*) lte - do not dial further if modem detects eSIM without profiles;
*) lte - exit LTE scan if modem reconfigured;
*) lte - fallback to RA for global IPv6 if unattained via AT channel (resets on config change);
*) lte - fixed eSIM management function for mmips and mipsbe architecture CPUs;
*) lte - fixed eSIM provisioning for servers that do not send content-length in the HTTP response;
*) lte - fixed inappropriate LTE interface inactive flag shown during modem initialization;
*) lte - fixed progress message for R11e-LTE modem firmware-upgrade;
*) lte - improved EC200A-EU firmware-upgrade stability;
*) lte - improved SMS sending stability over MBIM protocol;
*) macvlan - allow creating macvlan interfaces on all interfaces with a MAC address;
*) mpls - improved stability when handling VPLS packets;
*) netinstall-cli - improved client device architecture detection;
*) netwatch - added "early-success-detection" and "early-failure-detection" properties for ICMP probe;
*) port - improved port status handling at unexpected device removal;
*) ppp - added "dhcpv6-use-radius" PPP profile feature that enables "use-radius" option on dynamically created DHCPv6 servers;
*) ppp - added "remote-ipv6-prefix-reuse" PPP profile feature that allows to advertise same prefix on multiple VPN clients at the same time;
*) romon - changed default "disabled=yes" to "disabled=no" under /tool/romon/port;
*) romon - improved error message;
*) route - fixed destination ordering for SNMP;
*) route - fixed SNMP probing of IPv6 routes;
*) route - improved stability;
*) route - update router ID when disabled address is removed;
*) routing-filter - added sync command;
*) sfp - added sfp-power-class and sfp-max-power monitor values for QSFP (additional fixes);
*) smips - reduced package size, removed hotspot feature and provide it as a separate package;
*) ssh - show user public key fingerprint under /user/ssh-keys;
*) switch - fixed advertise and speed settings for ether1 on RB5009 (introduced in v7.20beta2);
*) switch - fixed egress-rate on QSFP ports;
*) switch - reset all Ethernet counters on reset-counters command on QoS Port menu;
*) system - fixed certain notifications (e.g. kid-control activity, connection tracking table) (introduced in v7.17);
*) veth - added dhcp=yes/no property to be able to easily run a container in LAN, runs a special dynamic dhcp-client on interface and sets acquired address/gateway/dns to in-container interface;
*) veth - added mac-address property;
*) veth - make veth interface MAC address stable in both RouterOS and container (container-side MAC incremented by +1 from RouterOS-side interface);
*) vrrp - added "conntrack-port" and "mode" settings for "sync-connection-tracking";
*) vxlan - improve stability when learning enabled interface used with EVPN (introduced in v7.20beta2);
*) webfig - fixed issue where legacy WebFig login page was used;
*) webfig - improved screen reader support for wifi fields in Quickset;
*) wifi - increased wifi scan list;
*) wifi-qcom - accept VLAN-tagged packets from clients with vlan-id;
*) wifi-qcom - fixed beacon loss issues and improved stability for IPQ-6018;
*) wifi-qcom - improved regulatory compliance;
*) winbox - added "Reselect Time" for wifi;
*) winbox - added "Digest Algorithm" under "System/Certificates" menu (additional fixes);
*) winbox - added "Note" field in LTE Firmware Upgrade;
*) winbox - fixed "Last Topology Change" for bridge port monitor;
*) winbox - fixed crash when opening entry in switch rule menu (introduced in v7.20beta2);
*) winbox - improved byte type field representation;
*) winbox - removed duplicate mounts option;
*) wireless - changed CLI snooper column name "freq" to "channel";
What’s new in 7.20beta2 (2025-May-27 13:33):
*) arm - improved system stability when processing encrypted traffic;
*) arm64 - increased maximum number of CPU cores to 128;
*) bgp - added brief, unnumbered output for advertisements list;
*) bgp - added initial EVPN support;
*) bgp - added NLRI filter for more precise accept/discard of ipv4/6 prefixes;
*) bgp - decode and log notifications;
*) bgp - introduced BGP instance configuration (note, downgrading to earlier versions without instance support may cause config issues);
*) bgp - print aigp attribute in advertisements;
*) bridge - added dynamic tagged entry named “switch-cpu” in scenarios where the same VLAN spans multiple switch chips or is used on both HW and SW ports;
*) bridge - added verbose STP debug logging (rx/tx BPDU, edge-port and port-role transitions, FDB flush);
*) bridge - disable/enable HW offload on bonding slave disable/enable (fixes potential MAC learning issue);
*) bridge - fixed port-id when adding a new port in non-primary MLAG;
*) bridge - refactored host learning logic in MLAG setups in order to make it more robust and predictable;
*) bth - added extra file-share functionality for use with apps;
*) bth - improved tunnel name in client config export;
*) bth,file - added direct file sharing from the WinBox Files menu;
*) certificate - improved stability after failed import;
*) chr - added Chelsio VF driver for PCIID 5803;
*) cloud - fixed restoring "BTH Files" service after a prolonged network outage;
*) cloud - reduced “BTH Files” ping interval dynamically upon failure;
*) console - added non-interactive (scriptable) serial-terminal support;
*) console - added use-tz option to :timestamp command;
*) console - fixed :convert to=num on MIPSBE;
*) console - improved stability and visuals for /interface/wireless/snooper/snoop;
*) console - improved visuals for brief print when displaying large tables;
*) console - improved visuals for hiding sensitive commands;
*) console - include flags by default when printing to value;
*) console - prioritize directory specific parameters and hide rarely used ones in print autocomplete;
*) console - replace TAB characters with spaces when editing scripts and added tab-width user configuration in /console/settings;
*) console - unified string representation of ID values;
*) console - updated hints for some /file/print parameters;
*) console - validate filenames upon addition (if enabled in /console/settings);
*) container - added "device" option to pass a device from /system/hardware menu to a container;
*) container - added /container/log menu, keep 100 messages per container;
*) container - added default print brief mode;
*) container - added initial support for container in container setups;
*) container - added option to execute commands inside a container using "/container/shell cmd= user=";
*) container - added per-container memory limiting and monitoring;
*) container - added SCTP support;
*) container - added support for cpuset, cpu, memory, pids cgroups;
*) container - allow picking passthrough devices by descriptive name;
*) container - allow read-only mounts;
*) container - allow to mount individual files, not just directories;
*) container - allow to specify multiple envlists;
*) container - allow to use multiple veths in a container, change the in container interface name to same as in RouterOS;
*) container - display any error prominently in WinBox;
*) container - do not allow multiple containers with same root directory;
*) container - enable check-certificate by default for new remote imports;
*) container - fixed containers that use inotify interface;
*) container - fixed environment variables not being passed to "/container/shell" properly;
*) container - improved compatibility when running containers with custom "cmd" and "entrypoint" commands;
*) container - improved error and log messages;
*) container - prevent user from setting "root-dir=/" for a container;
*) container - show a more descriptive error when tar extraction fails, particularly "No space left on device";
*) container - show config.json to user;
*) container - show explicit stopped flag for container;
*) container - stability improvements;
*) container - support for direct access to hardware devices;
*) container - terminate containers on shutdown, allow them to clean up properly;
*) dhcp - show error only after interface status is synced with the system (instead of erroneously displaying it immediately);
*) dhcp-client - always set the broadcast flag for DHCP Discover packets, except when renewing the lease;
*) dhcp-server - do not show "I" flag when server is disabled;
*) dhcpv4-client - allow specifying vlan-priority of outgoing packets (for VLAN interfaces only);
*) dhcpv4-server - added "lease-agent-circuit-id" and "lease-agent-remote-id" variables to the lease script;
*) dhcpv4-server - added "ntp-none" parameter;
*) dhcpv4-server - changed the default value of address-pool to "static-only" in the option matcher, removed "none" option;
*) dhcpv4/v6-client - properly resume client service after underlying interface status changes;
*) dhcpv4/v6-server - added CoA support;
*) dhcpv6-client - added "accept-prefix-without-address" allowing client to accept prefix when address is not available although requested;
*) dhcpv6-client - update the routing table and address list on manual client configuration changes;
*) dhcpv6-server - added "ignore-ia-na-bindings" setting that allows server to ignore address requests and work just with prefixes;
*) dhcpv6-server - do not trim real client DUID when assigning it to the binding;
*) discovery - disable discovery on loopback, LTE, ppp-out interfaces;
*) disk - allow to format multiple disks at once;
*) disk - allow to remove Btrfs device by ID;
*) disk - better manage disks disappearing from RAID;
*) disk - cleanup mountpoint when setting mount-filesystem=no;
*) disk - do Btrfs remove-device asynchronously;
*) disk - fixed RAID component size to match the value in the superblock;
*) disk - offer to blink only PCI slots in console;
*) disk - rename raid-role=unspecified to spare;
*) disk - reset RAID role of old disk after spare assumes a new role;
*) disk - show total/free inode counts for fs's that support it;
*) dlna - recognize flac extension;
*) fetch - display file sizes between 1–1023 bytes as 1KiB (instead of 0KiB);
*) fetch - include RouterOS version in the "User-Agent" field;
*) file - improved file handling performance in WinBox v4;
*) firewall - added connection tracking "total-ip4-entries" and "total-ip6-entries" counters;
*) firewall - allow "dst-limit" matcher to work properly above value 10000;
*) firewall - improved IPv6 connection tracking lookup responsiveness;
*) firewall - improved system stability when processing connections on multicore systems;
*) firewall - reorganized firewall connection tracking table values and make them persistent between IPv4 and IPv6;
*) flashfig - bind to local address (fixes issue when multiple interfaces are enabled);
*) hotspot - allow only "http" and "https" schemas in dst field;
*) iot - added an option to increase the amount of LoRa's traffic entries displayed;
*) iot - adjusted default LoRa antenna gain values for specific devices;
*) iot - iot-bt-extra package stability improvement and additional dongle support;
*) iot - LoRa stability improvements;
*) iot - LR8G/9G firmware update;
*) iot - removed lora-package, LoRa functionality was moved into iot-package;
*) iot - removed non-existent GPIO pin functionality;
*) ip - added socksify feature and new NAT action "socksify";
*) ipsec - fixed degraded IPsec performance for IPQ-6010 (introduced in v7.17);
*) ipv6 - added support for IPv6 ND proxying of individual addresses;
*) ipv6 - do not allow removal of dynamic address on lo interface;
*) ipv6 - make pref-src work and settable for static routes;
*) log - added command to clear memory action entries;
*) log - improved the "transmit loop detected" warning log;
*) log - output PoE-Out LLDP negotiation to poe,info topic;
*) lte - added "done" status for modem firmware-upgrade version check;
*) lte - added log entry if eSIM has no profiles on read;
*) lte - allow only one IPv6 APN for AT modems;
*) lte - display ICCID regardless of SIM PIN entry status;
*) lte - fixed modem recovery for unexpected modem reboot for Chateau 5G and Chateau 5G R16;
*) lte - fixed rare case where AT dialer could stop;
*) lte - refresh eSIM profile list after successful provision;
*) lte - renamed "uicc" to "iccid" in LTE monitor and eSIM profile print;
*) lte - show ip-type in /interface/lte/apn/print;
*) lte - use modem-supplied IPv6 address over EUI-64 when available;
*) net - fixed possible slave flag issues after user configuration changes;
*) net - improved system stability when processing TCP/UDP connections;
*) net - prevent removal of lo interface via WinBox;
*) netinstall - added after-install controls (reboot after installation, shutdown after installation, none);
*) netinstall - alert on unreadable configuration scripts;
*) netinstall - detect inactive install interface;
*) netinstall - fixed install for PPC devices;
*) netinstall - fixed mutually exclusive checkbox behavior;
*) netinstall - show router and package architecture;
*) netinstall - warn user if not enough space on device;
*) netinstall-cli - added MAC filter option "--mac";
*) netinstall-cli - added multiple install option "-m";
*) netwatch - fixed date and time for stats;
*) ovpn - added support for sha384 hmac;
*) ovpn - improved tunnel setup speeds in configurations with large ammount of active OVPN clients;
*) partitions - fixed failure to repartition correctly from 32MB partition size;
*) partitions - hide partition menu on unsupported boards (without NAND);
*) partitions - limit minimal partition size to 60MB;
*) poe-out - upgraded firmware for 802.3at/bt controlled boards (the update will cause brief power interruption to PoE-out interfaces);
*) port - added IPv6 support for "remote-access" tool;
*) ppp - added DHCPv6 assigned prefix to address list when configured and received from RADIUS;
*) ppp - added dhcpv6-lease-time profile configuration property;
*) ppp - do not send initial echo request if keepalive-timeout=disabled;
*) ppp - improved system stability when closing connections;
*) pppoe-server - added accept-untagged=yes/no option to accept untagged traffic in combination with pppoe-over-vlan-rage property;
*) ptp - added PTP support for RDS2216 device;
*) qos-hw - added mirror-buffers property and monitoring values;
*) radius - fixed issue with Session-Timeout attribute functionality;
*) route - added missing and remove unnecessary parameters from /ipv6/route menu;
*) route - afi naming consistency in logs;
*) route - attempt to clean up stuck routes in the routing table;
*) route - do not allow to modify dynamic routes;
*) route - make routing table print faster with hw-offload, gateway and blackhole queries;
*) routerboot - fixed boot MAC for CRS212 switch ("/system routerboard upgrade" required);
*) routing-filter - added filter-wizard (filter generator with v6-like syntax);
*) routing-filter - make "chain" and "list" parameters required when adding new item;
*) sfp - added sfp-power-class and sfp-max-power monitor values for QSFP;
*) sfp - fixed qsfp28 breakout disable;
*) sfp - improved initialization and linking for sfp28 on CRS518;
*) sfp - improved system stability with some GPON modules for CCR2004 and CCR2116 devices;
*) smips - reduced package size and removed hotspot capabilities;
*) sniffer - added CPU number and fast-path status in per-packet comment;
*) sniffer - save packets in pcapng format, it now includes interface name the packet was sniffed on, packet direction and nanosecond timestamp resolution;
*) snmp - added SNMP OIDs for firewall connection tracking "total-entries", "total-ip4-entries" and "total-ip6-entries";
*) ssh - improved stability on busy server;
*) ssh/sftp - fixed session disconnects during file transfer;
*) supout - added certificate settings section;
*) switch - fixed ACL rules when ports are not specified (fixes dynamic rules for RoMON);
*) switch - fixed port blocking by MSTP for 88E6393X, 88E6191X and 88E6190 switches;
*) switch - hide cpu-flow-control on irrelevant devices;
*) switch - improved bond MAC flush for 88E6393X, 88E6191X and 88E6190 switches;
*) switch - improved hash calculation for 98DX8208, 98DX8216, 98DX8212, 98DX8332, 98DX3257, 98DX4310, 98DX8525, 98DX3255, 98CX8410 switches (affects load balancing for bonds, ECMP routes, and VXLAN source port);
*) switch - improved ingress-rate limit precision for 88E6393X, 88E6191X and 88E6190 switches;
*) switch - rework ethernet counters (add tx-drop-queueX-byte/packet, tx-drop-byte/packet, tx-queueX-byte to /in/eth and updated GUI);
*) system - added support for OpenFlow 1.3 (new package "openflow" available);
*) system - do not automatically retry in case /system/package/update download fails;
*) system - fixed bb-upgrade failure on RB5009;
*) system - improved system configuration journaling procedure;
*) system - merge /system/resource/usb and /system/resource/pci into /system/resource/hardware and create a device tree;
*) usb - improved system stability after unplugging USB device for RB5009;
*) user - change /user/active/request-logout to /user/active/remove;
*) vrrp - added proxy-arp support;
*) vrrp - fixed sync-connection-tracking issue when parent interface is disabled/enabled;
*) vrrp - improved responsiveness when router has many IP addresses depending on VRRP state;
*) vrrp - make MTU property read-only;
*) vxlan - added checksum and learning properties;
*) webfig - added token authentication (no password prompt on reload or new window, logout button will log out all related sessions, removing a user will disconnect from active sessions);
*) webfig - allow network map scrolling in Dude;
*) webfig - basic mobile keyboard support for terminal;
*) webfig - do not show Keepalive if not set in GRE Tunnel form;
*) webfig - filter out unusable Bands and Channels for wifi interfaces;
*) webfig - fixed an issue where dynamic dropdown lists were hidden despite having values;
*) webfig - fixed hiding New button with skins;
*) webfig - fixed skin limits for radio buttons;
*) webfig - fixed Target field duplicate when disabling simple queue;
*) webfig - improved stability when displaying read-only scripts;
*) webfig - make columns a bit wider in tables;
*) webfig - make the Close buttons actual buttons, not links;
*) webfig - mask certain fields where values match default value;
*) webfig - more space to branding logo;
*) webfig - redesign logical "not" operator selector;
*) webfig - remove duplicate flag labels in QuickSet tables;
*) webfig - show system note on login;
*) webfig - use lexicographical sort in dropdown lists;
*) wifi - added tr069 support for wifi interfaces;
*) wifi - avoid picking 5GHz channels by default which are unlikely to be supported by clients, can be overridden with channel.deprioritize-unii-3-4 (CLI only);
*) wifi - restart CAPsMAN only on significant configuration changes;
*) winbox - added Address List Extra Time under "IP/DNS" menu;
*) winbox - added Digest Algorithm under "System/Certificates" menu;
*) winbox - added EAP identity under "WiFi/Registration" menu;
*) winbox - added Heartbeat under "Bridge/MLAG" menu;
*) winbox - added Installation under "WiFi" menu;
*) winbox - added missing Comments under "User Manager" menus;
*) winbox - added missing WPA2 PSK SHA2 option under "WiFi/Security" menu;
*) winbox - added MPLS Mangle;
*) winbox - added option to create new entries under "System/Users/SSH Keys" menu;
*) winbox - allow to specify CAPsMAN Address as IPv6 LL;
*) winbox - bump minimal WinBox version to 3.42;
*) winbox - correctly unset Locked CAPsMAN field;
*) winbox - differentiate PPP Profile Rx/Tx Queue settings;
*) winbox - display errors from the "Files/Sync" menu;
*) winbox - fixed container RAM parameter type;
*) winbox - fixed Record Type field under "Tools/Netwatch" menu;
*) winbox - make IPv6 Immediate Gateway read-only;
*) winbox - make log message field as multiline;
*) winbox - move CAPsMAN settings button from Remote CAP to WiFi table;
*) winbox - rename Ping Timeout field to Interval;
*) winbox - rename SMS Type field to Modem Type;
*) winbox - rework LTE firmware upgrade buttons into one window;
*) winbox - show "Switch" related menus only on boards that support such features;
*) winbox - use same WireGuard default values as in console;
To upgrade, click “Check for updates” at /system package in your RouterOS configuration interface, or head to our download page: http://www.mikrotik.com/download
If you experience version related issues, then please send supout file from your router to support@mikrotik.com. The file must be generated while a router is not working as suspected or after some problem has appeared on the device
Please keep this forum topic strictly related to this particular RouterOS release.
But it makes sense, OpenWrt Two is on horizon.